Analyzing and Simulating of 4-Bar Mechanism Motion Based on ADAMS

HOU Hong-ling,ZHAO Yong-qiang,WEI Wei-feng

DOI: https://doi.org/10.3969/j.issn.1006-0316.2005.06.013

2005-01-01

Abstract:Introducing the dynamic simulation of ADAMS, Bringing forward a method of analyzing the plane mechanism motion using the technology of simulation.

What problem does this paper attempt to address?

Kinematics and dynamicsanalysis for slotting machine six bar linkage

Su-di YE,Jing-hua XU

DOI: https://doi.org/10.3969/j.issn.2095-0977.2014.04.008

2014-01-01

Abstract:The slotting tool moves up and down in the slotting machine,which is directly related to the workpiece cutting efficiency and quality.Establishing the vector model of slotting machine six bar link-age,then using differential module in the matlab/simulink to establish the simulation diagram,and set-ting up reasonable initial conditions,the motion results can be visualized,with the displacement,velocity and acceleration curve of the slotting tool obtained.Adj usting the relative length of components can lead to different movement curves,which will realize the quickness of mechanism design.The total reaction force of various components can be determined by analysizing the mechanism of stress distribution through making friction circle and j udging the relative angular velocity,and referencing the principle that the friction force is always tangent to the friction circle and torque direction produced from hinge center is opposite to the relative angular velocity.And then inertia force is applied to the corresponding artifacts. At last,the principle can be concluded that equilibrium torque of the main thing changes with time by carrying out the dynamic static analysis of d'Alembert principle.
Study on Motion Simulation Method of Parallel Mechanism Based on ADAMS

Huan Gong Wang,Xiao Qing Wu,Li Ping Wang,Ning Min Kang

DOI: https://doi.org/10.4028/www.scientific.net/amm.389.590

2013-01-01

Applied Mechanics and Materials

Abstract:This paper takes a parallel mechanism of a loading test device, analyzes a degree of freedom of the parallel mechanism, builds a geological model in ADAMS software, applies restriction and load, and sets a performance function; this paper solves the problem of Jacobian matrix ambiguity of the parallel mechanism through releasing three kinematic pairs in ADAMS, transforms the solved angle to Euler angle of coordinate series of two parts through local coordinate system of ADAMS, simulates and solves the included angle movement scale between following ground jack 5 and dynamic and static platforms through the performance function of ADAMS, thereby providing accordance for the design of the loading test device.
Kinematics and Inverse Dynamic Analysis of a 6 Channel Half-axle Test Rig

Fu Yi-Meng,Zhou Xiao-Jun,Yang Xue-Feng,Xiao Peng

DOI: https://doi.org/10.1109/icrae53653.2021.9657823

2021-01-01

Abstract:For the inverse dynamic analysis of the 6 channel half-axle test rig, the inverse dynamics model is established for the series-parallel hybrid mechanism by using the closed-loop vector chain method and Kane's method. Kane's method model is simulated in MATLAB/Simulink, while the virtual prototype model is simulated in Adams. The results of the final simulation show that the preceding dynamic model is efficient and adapted to the 6-channel half-axle test platform.
Modeling and Motion Simulation of New Type 3P-1R Parallel Mechanism Based on CAXA and ADAMS

Zhang Qinggong,Ma Xiaoli,Wang Jianping

DOI: https://doi.org/10.3969/j.issn.1000-4998.2008.02.006

2008-01-01

Abstract:Based on the build-up principle of the parallel manipulator with single-opened-chain as its units,a new type 3P-1R parallel mechanism is provided.The 3D model of the parallel mechanism is established with the help of CAXA and the motion simula- tion of virtual prototype of this mechanism is implemented with the help of ADAMS.The result shows that the motion law of the moving platform of the 3P-1R parallel mechanism conforms to the theoretical calculation.There is a high reliability in motion simulation.
Dynamic Analysis of a Hybrid-driven 7-Bars Mechanism

TANG Bing-han,GUO Wei-zhon

DOI: https://doi.org/10.3969/j.issn.1006-2343.2007.02.005

2007-01-01

Abstract:Dynamic modeling of parallel mechanism is the precondition for it s mo t ion control with high speed and high precision.This paper proposes a hybrid driven parallel mechanism,then analyzes the dynamic modeling of a 7-bars mechanism through Lagrange Equation,and has the dynamic simulation with Matlab to get the real movement patterns of the two motors,which help the trajectory planning and control method of mechanism.
Optimization Design of Four-Bar Linkage of Hydraulic Support Based on ADAMS

Xin Zhang,Jianwu Zhang,Qingliang Zeng,Hanzheng Dai

DOI: https://doi.org/10.1109/icic.2009.396

2009-01-01

Abstract:In designing a large inclined angle hydraulic support, the structure characteristics of four-bar linkage is presented, and ADAMS software is applied to four-bar linkage modeling and simulation. In order to attain optimal results, parameterized modeling and optimization is achieved, and the design results meets the practical requirements very well. By means of this virtual design method, the errors can be reduced and design efficiency can be improved effectively.
STABLE PROGRAMMED MANIFOLD SOLVER FOR VIRTUAL PROTOTYPING MOTION SIMULATION

Zhenyu Liu

2006-01-01

Abstract:Based on constructing programmed constraint and constraint perturbation equation, a kinematics and dynamics numerical simulation model is established for virtual mechanism, in which the difference scheme guarantee precision in simulation procedure and its numerical solutions satisfy programmed manifold stability. A crank-piston mechanism in a car engine, a steering mechanism and a suspension mechanism are simulated in a virtual environment, then comparing the simulation results with those obtained in ADAMS under the same circumstances proved the solver valid.
Simulation Analysis of Manual Hydraulic Crane Based on ADAMS

Zheng Li,Zhu Jiang-feng,He Wang,Yu Lanhao,Guoliang Wu

DOI: https://doi.org/10.25236/ijndes.17421

2017-01-01

Abstract:Use solidworks to establish the manual hydraulic crane three-dimensional model, use ADAMS software to kinematics and dynamics simulation. Obtain the force value curve at main hinge points , acceleration value curve and velocity value curve during lifting process, which provides reference for manual hydraulic crane design and optimization.
Modeling of AMESim Based Hydraulic Parallel Mechanism and Simulation of Its Coupling Characteristics

WANG Wei,FU Xin,XIE Hai-bo,YANG Hua-yong

DOI: https://doi.org/10.3785/j.issn.1008-973x.2007.11.021

2007-01-01

Abstract:A novel universal simulation model of hydraulic six-degree of freedom parallel mechanism was presented,in which the hydraulic actuator servo system was built in the AMESim,and the parallel mechanism part was built in the Simulink.In the AMESim model,the equivalent load of hydraulic actuator is from the Simulink model instead of equivalent mass.The combined simulation model takes the details of hydraulic system into consideration to ensure the accuracy,and provides a convenient research technique for hydraulic parallel mechanism.The coupling characteristic of the parallel mechanism was studied through analyzing the dynamic consistency of six actuators using the simulation model.The results show that coupling phenomena appear when the frequency responses of the six actuators were different,and the coupling becomes stronger when the difference among the actuators increases.Thus the dynamic consistency of all actuators must be ensured during the design of parallel mechanism.
Kinematics simulation of the anthropomorphic manipulator based on Pro/E and ADAMS

Bojun Li,Ling Huang

DOI: https://doi.org/10.1109/MIC.2013.6758148

2013-01-01

Abstract:A kinematics simulation for the anthropomorphic manipulator is completed in the paper based on Pro/E and the automatic dynamic analysis of mechanical systems (ADAMS). First Pro/E software (Pro-Engineer) is used to establish 3d entity model of the anthropomorphic manipulator. Then the 3d entity model is imported into the automatic dynamic analysis of mechanical systems. Thirdly the kinematics simulation analysis of anthropomorphic manipulator is carried out, which provides the position, velocity, acceleration curves of anthropomorphic manipulator finger joints. This is a method to clarify the effectiveness of the design for anthropomorphic manipulator.
Dynamic simulation of mechanism of GT421 dobby based on ADMAS

SHEN Yi,GAO Daniu,LIU Chunlei

DOI: https://doi.org/10.3969/j.issn.0253-9721.2012.08.023

2012-01-01

Abstract:In order to conduct a reasonable dynamic simulation of the mechanism of GT421 rotary electronic dobby,firstly it needs a reasonable simplification and analysis of the main drive mechanism,and then completes the modeling,assembly and dynamic simulation of the heald lifting mechanism by Pro/E and ADMAS,and finally obtains the movement rule of each component in the mechanism and the dynamic force acting on them.It makes a theoretical analysis and calculation of the relative pause time between the spline shaft and the rocker arm,checks the main transmission mechanism model,and analyzes the strength of the key vulnerable components of the mechanism based on the statics design.Furthermore considering the impact of the speed on the mechanisms motion and the component′ stress,it also makes the mechanism simulation of the input disc at three typical speeds.
The Kinematics Simulation and Analysis of a New Spraying Robot Based on ADAMS

ZHOU Qifeng,ZOU Guojun

DOI: https://doi.org/10.3969/j.issn.1002-6886.2011.01.013

2011-01-01

Abstract:In this paper,the forward kinematics equation of spraying robot is built by the D-H method.The whole workspace of the 6 dof painting robot was drawn on the basis of kinematics analysis of this robot by using Matlab software.Using ADAMS software to build the Virtual Prototype Model of the robot and do some simulation analysis which not only proves the correctness of the kinematics Model and also build the foundation for future research.
Kinematics Simulation of 5-DOF Parallel Mechanisms

Haidong Yu,Qiang Guo,Guohua Cui

DOI: https://doi.org/10.1145/3366194.3366322

2019-01-01

Abstract:Taking a 5-DOF 4-SPRR-SPR parallel mechanism as the research object, the spiral theory is used to analyze the degree of freedom of the 4-SPRR-SPR parallel mechanism, and the closed-vector method is used to establish the inverse kinematics equation of the parallel mechanism.The virtual prototype is built by Solidworks, and it is imported into Adams to verify the correctness of kinematics inverse solution by taking the welding sphere as an example. The velocity, acceleration curve and force of the driving rod at the end of the mechanism are obtained. The results show that the mechanism has five degrees of freedom of 3T2R, and its inverse solution is fast and convergent. The inverse kinematics solution is correct and the force transfer performance of the driving rod is good. Because of its characteristics of five degrees of freedom, high stiffness and high bearing capacity, this mechanism has great application prospects in friction stir welding of complex surface in space.
Realization of 3D Modeling and Kinematics Simulation on a New 3P- 1R Parallel Mechanism

XIE Hui-ping,ZHANG Ying,ZHANG Qing-gong,MA Xiao-li

DOI: https://doi.org/10.3969/j.issn.1672-1616.2008.03.014

2008-01-01

Abstract:Based on the structure theory of parallel robot mechanism and the units of the single-opened-chain limb,it synthesizes a new 4-DOF parallel robot mechanism with 3-translation and 1-rotation.The 3D parametric model of the new 3P-1R parallel mechanism is established in CAXA system.The virtual prototype of the 3P-1R parallel mechanism is constructed in ADAMS.The kinematics simulation of this prototype is realized.Good coincidence between simulation results and theoretic calculated values proves that the virtual prototype of the 3P-1R parallel mechanism is reliable and the kinematics simulation results are credible.
The Kinematic Analysis and Parametric Design of Beam Pumping Unit Based on ADAMS

Yuan Liu,Haitao Wu,Hongbin Liu

DOI: https://doi.org/10.1109/icdma.2011.319

2011-01-01

Abstract:This paper used the ADAMS mechanical systems dynamic simulation to estabLish the virtual prototype model of CYJY12-4.2-73-type beam-pumping unit. Through some parameters calculation and movement analysis, we obtained the rules of suspension point displacement, velocity and acceleration. From the movement rules of suspension point, we saw some weak points. We carried out parametric design and analysis for several parameters of the pumping units using the Design Study of ADAMS, which was amid at the crank shaft torque of the reducer. Our work can be a reference to the designer.
Dynamic simulation analysis for docking mechanism of on-orbit-servicing satellite

Yuan Zhang,Jian Wang,Yan Song,Lili Sun

DOI: https://doi.org/10.4028/www.scientific.net/AMM.487.313

2014-01-01

Applied Mechanics and Materials

Abstract:The new type of three jaw docking mechanism is designed for use in orbiting spacecraft, the mathematical model is given and its working characteristics are analyzed. By establishing the mathematical model of the interaction of the parts under the different coordinate system, it is obtained that the corresponding kinematic characteristics; contact collision dynamics model is established by using the Hertz model theory, dynamic equation is established by Newton-Euler method, and simulation analysis are carried out by using the dynamics simulation software ADAMS, through the simulation analysis of three groups with different initial conditions, the results show that it achieve reliable grasp with good performance, it provides the lock claw curve in contact collision force and movement characteristics curve. These curves provide reference to improve the performance of docking mechanism.
Dynamic Modeling and Design of 3T-1R Parallel Robot

马晓丽,张庆功,张雪莲

DOI: https://doi.org/10.3969/j.issn.1003-0794.2008.11.022

2008-01-01

Abstract:A dynamic analysis method of the new 4-DOF parallel robot mechanism was presented.Static-equilibrium equations of the parallel mechanism ware established by virtual displacement principle of the analytical statics and Jacobian matrix,and the equations ware validated by computing and simulating.The dynamic modeling was established adopting D'Alembert principle,and dynamic simulations of the mechanism were done by ADAMS software.
Error Analysis and Calibration of a 4-DOF Parallel Mechanism

刘红军,龚民,赵明扬

DOI: https://doi.org/10.3321/j.issn:1002-0446.2005.01.002

2005-01-01

ROBOT

Abstract:This paper proposes a novel 4-dof parallel mechanism. The kinematics of this mechanism is presented firstly, and then the kinematics error model is given and analyzed using perturbation method. After a simple review of the kinematics calibration technology of this parallel mechanism, two calibration methods for error model analysis on this mechanism are discussed in detail. Finally, the simulation results are given based on the IK(inverse kinematic) calibration in the Matlab environment.
Kinematic Analysis of Two Degree of Freedom Spherical Fixed-point Five-bar Parallel Mechanism

FANG Xin,XU Min,GAO Feng

DOI: https://doi.org/10.3321/j.issn:1006-2467.2009.05.031

2009-01-01

Abstract:Based on the spatial kinematics analysis,a kinematic model of two-degree-offreedom spherical fixed-point five-bar mechanism driven by parallel four-bar linkage was set up by means of Euler angle and spherical analytic geometry.The kinematics of the mechanism was solved.This proves the validity and accuracy comparing with the kinematics simulation.The calculated solution by this method is significant to the further dynamic analysis.
Dynamic Simulation and Optimization Design for Forging Manipulator Based on ADAMS

陈博翁,关立文,李铁民

DOI: https://doi.org/10.3969/j.issn.1001-3997.2009.03.003

2009-01-01

Abstract:The virtual prototype of a 5-degree-of-freedom forging manipulator is built based on 3D modeling software Pro/E and dynamic analysis software ADAMS. Then a dynamic simulation and optimization design is carried out. The method provides a efficient way for the design of forging manipulators.

Analyzing and Simulating of 4-Bar Mechanism Motion Based on ADAMS

Kinematics and dynamicsanalysis for slotting machine six bar linkage

Study on Motion Simulation Method of Parallel Mechanism Based on ADAMS

Kinematics and Inverse Dynamic Analysis of a 6 Channel Half-axle Test Rig

Modeling and Motion Simulation of New Type 3P-1R Parallel Mechanism Based on CAXA and ADAMS

Dynamic Analysis of a Hybrid-driven 7-Bars Mechanism

Optimization Design of Four-Bar Linkage of Hydraulic Support Based on ADAMS

STABLE PROGRAMMED MANIFOLD SOLVER FOR VIRTUAL PROTOTYPING MOTION SIMULATION

Simulation Analysis of Manual Hydraulic Crane Based on ADAMS

Modeling of AMESim Based Hydraulic Parallel Mechanism and Simulation of Its Coupling Characteristics

Kinematics simulation of the anthropomorphic manipulator based on Pro/E and ADAMS

Dynamic simulation of mechanism of GT421 dobby based on ADMAS

The Kinematics Simulation and Analysis of a New Spraying Robot Based on ADAMS

Kinematics Simulation of 5-DOF Parallel Mechanisms

Realization of 3D Modeling and Kinematics Simulation on a New 3P- 1R Parallel Mechanism

The Kinematic Analysis and Parametric Design of Beam Pumping Unit Based on ADAMS

Dynamic simulation analysis for docking mechanism of on-orbit-servicing satellite

Dynamic Modeling and Design of 3T-1R Parallel Robot

Error Analysis and Calibration of a 4-DOF Parallel Mechanism

Kinematic Analysis of Two Degree of Freedom Spherical Fixed-point Five-bar Parallel Mechanism

Dynamic Simulation and Optimization Design for Forging Manipulator Based on ADAMS