Abstract:Abstract Chemical-looping combustion (CLC) is a combustion process with inherent separation of carbon dioxide (CO 2 ), which is achieved by oxidizing the fuel with a solid oxygen carrier rather than with air. As fuel and combustion air are never mixed, no gas separation is necessary and, consequently, there is no direct cost or energy penalty for the separation of gases. The most common form of design of chemical-looping combustion systems uses circulating fluidized beds, which is an established and widely spread technology. Experiments were conducted in two different laboratory-scale CLC reactors with continuous fuel feeding and nominal fuel inputs of 300 W th and 10 kW th , respectively. As an oxygen carrier material, ground steel converter slag from the Linz–Donawitz process was used. This material is the second largest flow in an integrated steel mill and it is available in huge quantities, for which there is currently limited demand. Steel converter slag consists mainly of oxides of calcium (Ca), magnesium (Mg), iron (Fe), silicon (Si), and manganese (Mn). In the 300 W unit, chemical-looping combustion experiments were conducted with model fuels syngas (50 vol% hydrogen (H 2 ) in carbon monoxide (CO)) and methane (CH 4 ) at varied reactor temperature, fuel input, and oxygen-carrier circulation. Further, the ability of the oxygen-carrier material to release oxygen to the gas phase was investigated. In the 10 kW unit, the fuels used for combustion tests were steam-exploded pellets and wood char. The purpose of these experiments was to study more realistic biomass fuels and to assess the lifetime of the slag when employed as oxygen carrier. In addition, chemical-looping gasification was investigated in the 10 kW unit using both steam-exploded pellets and regular wood pellets as fuels. In the 300 W unit, up to 99.9% of syngas conversion was achieved at 280 kg/MW th and 900 °C, while the highest conversion achieved with methane was 60% at 280 kg/MW th and 950 °C. The material’s ability to release oxygen to the gas phase, i.e., CLOU property, was developed during the initial hours with fuel operation and the activated material released 1–2 vol% of O 2 into a flow of argon between 850 and 950 °C. The material’s initial low density decreased somewhat during CLC operation. In the 10 kW, CO 2 yields of 75–82% were achieved with all three fuels tested in CLC conditions, while carbon leakage was very low in most cases, i.e., below 1%. With wood char as fuel, at a fuel input of 1.8 kW th , a CO 2 yield of 92% could be achieved. The carbon fraction of C 2 -species was usually below 2.5% and no C 3 -species were detected. During chemical-looping gasification investigation a raw gas was produced that contained mostly H 2 . The oxygen carrier lifetime was estimated to be about 110–170 h. However, due to its high availability and potentially low cost, this type of slag could be suitable for large-scale operation. The study also includes a discussion on the potential advantages of this technology over other technologies available for Bio-Energy Carbon Capture and Storage, BECCS. Furthermore, the paper calls for the use of adequate policy instruments to foster the development of this kind of technologies, with great potential for cost reduction but presently without commercial application because of lack of incentives.

Life Cycle Assessment of Coal Direct Chemical Looping Hydrogen Generation with Fe2O3 Oxygen Carrier

Numerical Study on the Process of Chemical Looping Hydrogen Production with Multiple Circulating Fluidized Bed Reactors

A new scheme for ammonia and fertilizer generation by coal direct chemical looping hydrogen process: Concept design, parameter optimization, and performance analysis

Performance of hydrogen and power co-generation system based on chemical looping hydrogen generation of coal

Hydrogen and Power Cogeneration Based on Chemical Looping Combustion: Is It Capable of Reducing Carbon Emissions and the Cost of Production?

Comparative life cycle energy, water consumption and carbon emissions analysis of deep in-situ gasification based coal-to-hydrogen with carbon capture and alternative routes

Coal-fueled chemical looping gasification: A CFD-DEM study

Life cycle energy-economy-environmental evaluation of coal-based CLC power plant vs. IGCC, USC and oxy-combustion power plants with/without CO<sub>2</sub> capture

Comprehensive optimization of coal chemical looping gasification process for low CO 2 emission based on multi-scale simulation coupled experiment

Life cycle energy-economy-environmental evaluation of coal-based CLC power plant vs. IGCC, USC and oxy-combustion power plants with/without CO2 capture

Long-term coal chemical looping gasification using a bimetallic oxygen carrier of natural hematite and copper ore

Research and Development of Coal-fueled Chemical Looping Combustion

Test Operation of a Separated-Gasification Chemical Looping Combustion System for Coal

Thermodynamic Analysis of 350 MWe Coal Power Plant Based on Calcium Looping Gasification with Combined Cycle

Conversion of metallurgical coke and coal using a Coal Direct Chemical Looping (CDCL) moving bed reactor

Modelling of multiphase reactive flows in a full-loop coal-direct chemical looping combustor

Pressurized Chemical-Looping Combustion of Chinese Bituminous Coal: Cyclic Performance and Characterization of Iron Ore-Based Oxygen Carrier

Optimal design, thermodynamic, cost and CO2 emission analyses of coal-to-methanol process integrated with chemical looping air separation and hydrogen technology

Life cycle assessment of a biomass based chemical looping combustion

Pressurized chemical-looping combustion of coal using an iron ore as oxygen carrier in a pilot-scale unit

Avoiding CO2 capture effort and cost for negative CO2 emissions using industrial waste in chemical-looping combustion/gasification of biomass