Abstract:Natural gas (NG)-diesel dual fuel engines have been criticized for their high emissions of unburned methane. The past research on methane emissions from dual fuel engines has focused on the measurement of methane concentration in exhaust gases. The development of approaches capable of minimizing methane emissions requests the detailed spatial distribution of methane in-cylinder during the combustion and post combustion processes. However, it is difficult to experimentally measure the spatial distribution of methane in-cylinder. This research presents a numerical study on the combustion process of a NG-diesel dual fuel engine using the computational fluids dynamics (CFD) model CONVERGE coupled with a reduced primary reference fuel (PRF) mechanism. The model was validated against the heat release process and the emissions of nitrogen oxide, methane and carbon monoxide measured in a single cylinder dual fuel engine. The validated CFD model was applied to investigate the combustion of methane and n-heptane and the spatial distribution of methane in the dual fuel engine. This is most likely the first attempt to visualize the spatial distribution of methane in dual fuel engines using CFD. The objective of this study is to numerically simulate the methane combustion process, especially the methane present outside the pilot spray, quantify the methane combustion in each combustion stage, and visualize the spatial methane distribution in cylinder. The results showed that the momentum produced by the pilot fuel injection and combustion pushed the combustion products of pilot fuel and methane within the pilot spray plume toward the unburned methane-air mixture. Such a movement enhanced the mixing of the hot combustion products and the relatively cold unburned methane-air mixture during the main combustion process and dominated the combustion of methane presented outside the pilot fuel spray plume. Based on the simulation results at a low load condition (4.05 bar), the main combustion process consumed 43-53% of the methane fumigated into the intake mixture. The post-combustion oxidation process consumed 17-29% of the intake methane, which was 36.2-51.8% methane that survived the main combustion process. In comparison, 27-35% methane emitted the engine without participating the combustion process. The unburned methane at exhaust valve opening was mainly observed at the center of the cylinder. In comparison, the contribution of the crevice and boundary layer around the cylinder liner to methane emissions was relatively small. The slip of methane through the dual fuel engines was due to the fact that the premixed mixture was too lean to support the propagation of the turbulent flame initiated by the pilot fuel and the lack of pilot fuel vapor reaching the center of the combustion chamber because of the geometric limitations of the fuel injection system and the reduced mass of pilot fuel injected into the cylinder. The approaches aiming to enhance the combustion of methane and minimize methane emissions from dual fuel engines should focus on those capable of increasing the volume of pilot fuel vapor formed after injected into the cylinder.

Use of a Convenient Thermodynamic Model to Study the Effects of Operating Parameters on Nitrogen Oxides Emissions for a Liquefied Methane Fueled Spark-Ignition Engine

Numerical Investigation of Methane Number and Wobbe Index Effects in Lean-Burn Natural Gas Spark-Ignition Combustion

Optical and Numerical Investigations of Flame Propagation in a Heavy Duty Spark Ignited Natural Gas Engine

Improved Thermodynamic Model for Lean Natural Gas Spark Ignition in a Diesel Engine Using a Triple Wiebe Function

Numerical Investigation of the Effect of Ammonia Addition on the Performance of a Stoichiometric Operated Natural Gas Spark Ignition Engine

An Experimental Study of the Combustion Process in a Natural-Gas Spark-Ignition Engine

Investigation of Multistage Combustion Inside a Heavy-Duty Natural-Gas Spark-Ignition Engine Using Three-Dimensional Computational Fluid Dynamics Simulations and the Wiebe-Function Combustion Model

Formation and Evolution of Thermal and Fuel Nitrogen Oxides in the Turbulent Combustion Field of Ammonia Internal Combustion Engines

Influences of the Control Parameters and Spark Plug Configurations on the Performance of a Natural Gas Spark-Ignition Engine

Experimental and Numerical Study the Effect of EGR Strategies on In-Cylinder Flow, Combustion and Emissions Characteristics in a Heavy-Duty Higher CR Lean-Burn NGSI Engine Coupled with Detail Combustion Mechanism

A numerical investigation on the effects of gaseous fuel composition in a pilot ignited direct injection natural gas engine

Quantitative Investigation of the Effects of CR, EGR and Spark Timing Strategies on Performance, Combustion and NOx Emissions Characteristics of a Heavy-Duty Natural Gas Engine Fueled with 99% Methane Content

Investigations on combustion system optimization of a heavy-duty natural gas engine

Experimental Investigation on the Effects of Compression Ratio on in Cylinder Combustion Process and Performance Improvement of Liquefied Methane Engine

Chemical Kinetics and Numerical Simulation of NO Emission Characteristics in CH4/NH3/air Flame

A Numerical Investigation on Methane Combustion and Emissions from a Natural Gas-Diesel Dual Fuel Engine Using CFD Model

The Effects of Partially Premixed Combustion Mode on the Performance and Emissions of a Direct Injection Natural Gas Engine

Numerical Study on the Effect of the Combustion System Parameters on Combustion and Emission Characteristics for a HPDI Natural Gas/diesel Dual Fuel Engine

Quantitative Analysis on the Effects of Compression Ratio and Operating Parameters on the Thermodynamic Performance of Spark Ignition Liquefied Methane Gas Engine at Lean Burn Mode

Numerical investigation on combustion regulation for a stoichiometric heavy-duty natural gas engine with hydrogen addition considering knock limitation

Optimization of Combustion Chamber Geometry for Natural Gas Engines with Diesel Micro-Pilot-Induced Ignition