Abstract:The durability of manufactured sand concrete prepared in a simulated plateau environment was investigated. Several factors, such as preparation environment of the specimens, concrete strength and corrosion rate of steel bar, were considered in this study. In these experimental investigations, the accelerated corrosion test on specimens exposed to a chloride salt solution and thereafter the static tensile test on corroded steel bars retrieved from these specimens were carried out. The durability of different specimens was compared by analyzing the surface crack development on the concrete surface, the corrosion morphologies of embedded steel bars, the degradation of mechanical properties of steel bars, and the concrete microstructure. In addition, the differences observed in the crack development of concrete and the degradation of mechanical properties of corroded steel bars between plateau and normal exposure environments were quantified. The results show that the steel bars embedded in the specimens prepared in a simulated plateau environment are prone to non-uniform corrosion attack, especially for the specimens with low concrete strength. The preparation environment of specimens and concrete strength have little influence on the degradation of mechanical properties of steel bar when subjected to a theoretical corrosion rate less than 6 %. Compared with the specimens prepared in a normal environment, the yield strength, ultimate strength and elongation of corroded steel bars subjected to a theoretical corrosion rate in the range 2∼10 % in specimens prepared in a plateau environment decrease by 2.99 %, 4.44 % and 14.78 % on average, respectively. For the specimens prepared in a plateau environment the decreased durability of concrete is explained by insufficient hydration and low compactness inside concrete, so that it is easier for chloride ions to penetrate into concrete, resulting in early corrosion. As a result, the variation of average crack width of concrete with actual corrosion rate and the variation of nominal yield and ultimate strengths of steel bars with their maximum section loss rates no longer satisfy the linear relationship for the specimens prepared in plateau environment, which is different from the specimens prepared in a normal environment. Moreover, the protective effect of concrete on embedded steel bar can be significantly enhanced by improving the strength of concrete produced in a plateau environment.

Corrosion Resistance of Steel Bar and Chloride Binding Capacity of Cementitious Materials with Internal Chloride

Compressive Strength and Chloride Resistance of Slag/Metakaolin-Based Ultra-High-Performance Geopolymer Concrete.

Effect of modified supplementary cementitious material on performance of mortar and concrete in marine environment

Preparation technology, mechanical properties and durability of coral aggregate seawater concrete in the island-reef environment

A study of chloride binding capacity of concrete containing supplementary cementitious materials

Mechanical Performance and Chloride Penetration of Calcium Sulfoaluminate Concrete in Marine Tidal Zone

Chloride-induced Corrosion Patterns of Reinforcements in Simulated Pore Solutions of Calcium Sulfoaluminate Cement Concrete: an Analytical Study

Resistance of Chloride and Sulfate of Geopolymer based on fly ash and silica fume as alternative raw materials.

The Resistance of Novel Concrete Prepared by Gap-Graded Blended Cement under Chloride-Sulfate Attack

Feasibility and Application of Concrete Containing Chloride-rich Offshore Sand

Structural behavior of GFRP reinforced concrete columns under the influence of chloride at casting and service stages

Geopolymer Composites for Marine Application: Structural Properties and Durability

Atmospheric chloride-induced corrosion of steel-reinforced concrete beam exposed to real marine-environment for 7 years

Optimal Design and Performance of Concrete with Function Component in Marine Environment

Calcined Clay and Limestone as Partial Replacements of Portland Cement: Electrochemical Corrosion Behavior of Low Carbon Steel Rebar as Concrete Reinforcement in Corrosive Environment

Degradation characteristics of Portland cement mortar incorporating supplementary cementitious materials under multi-ions attacks and drying-wetting cycles

Chloride resistance of class C/class F fly ash-based geopolymer mortars with different strength grades

Chloride Corrosion Resistance of Manufactured Sand Reinforced Concrete Prepared in Plateau Environment

Chloride erosion resistance of calcium formate incorporated cement mortar under chloride attack

Chloride penetration resistance and chloride binding capacity under different application environments of ferroaluminate cement

Durability and Improvement of Cement-Based Revetment Materials Serving in Subtidal, Intertidal, and Supratidal Environments