Abstract:A novel micro/nanoscale rough structured superhydrophilic hybrid-coated mesh that shows underwater superoleophobic behavior is fabricated by spray casting or dipping nanoparticle–polymer suspensions on stainless steel mesh substrates. Water droplets can spread over the mesh completely; meanwhile, oil droplets can roll off the mesh at low tilt angles without any penetration. Besides overcoming the oil-fouling problem of many superhydrophilic coatings, this superhydrophilic and underwater superoleophobic mesh can be used to separate oil and water. The simple method used here to prepare the organic–inorganic hybrid coatings successfully produced controllable micro-nano binary roughness and also achieved a rough topography of micro-nano binary structure by controlling the content of inorganic particles. The mechanism of oil–water separation by the superhydrophilic and superoleophobic membrane is rationalized by considering capillary mechanics. Tetraethyl orathosilicate (TEOS) as a base was used to prepare the nano-SiO2 solution as a nano-dopant through a sol-gel process, while polyvinyl alcohol (PVA) was used as the film binder and glutaraldehyde as the cross-linking agent; the mixture was dip-coated on the surface of 300-mesh stainless steel mesh to form superhydrophilic and underwater superoleophobic film. Properties of nano-SiO2 represented by infrared spectroscopy and surface topography of the film observed under scanning electron microscope (SEM) indicated that the film surface had a coarse micro–nano binary structure; the effect of nano-SiO2 doping amount on the film’s surface topography and the effect of such surface topography on hydrophilicity of the film were studied; contact angle of water on such surface was tested as 0° by the surface contact angle tester and spread quickly; the underwater contact angle to oil was 158°, showing superhydrophilic and underwater superoleophobic properties. The effect of the dosing amount of cross-linking agent to the waterproof swelling property and the permeate flux of the film were studied; the oil–water separation effect of the film to oil–water suspension and oil–water emulsion was studied too, and in both cases the separation efficiency reached 99%, which finally reduced the oil content to be lower than 50 mg/L. The effect of filtration times to permeate flux was studied, and it was found that the more hydrophilic the film was, the stronger the stain resistance would be, and the permeate flux would gradually decrease along with the increase of filtration times.

Environmentally Benign Development of Superhydrophilic and Underwater Superoleophobic Mesh for Effective Oil/water Separation

Fabrication of a Novel Superhydrophobic and Superoleophilic Surface by One-Step Electrodeposition Method for Continuous Oil/water Separation

Ni-Al Layered Double Hydroxides (ldhs) Coated Superhydrophobic Mesh with Flower-Like Hierarchical Structure for Oil/water Separation

Micro/Nanoscale Structured Superhydrophilic and Underwater Superoleophobic Hybrid-Coated Mesh for High-Efficiency Oil/Water Separation

Robust Photopolymerized Superoleophobic/Superhydrophilic Mesh for Oil-Water Separation

Facile Preparation of Superhydrophilic and Underwater Superoleophobic Mesh for Oil/water Separation in Harsh Environments

Superhydrophilic and underwater superoleophobic cement-coated mesh for oil/water separation by gravity

Superhydrophobic–superoleophilic stainless steel meshes by spray-coating of a POSS hybrid acrylic polymer for oil–water separation

A self-cleaning TiO2 coated mesh with robust underwater superoleophobicity for oil/water separation in a complex environment

Facile preparation of durable superhydrophobic-superoleophilic mesh using simple chemical oxidation for oil-water separation under harsh conditions

Fabrication of a superhydrophilic/underwater superoleophobic stainless steel mesh for oil/water separation with ultrahigh flux

Bioinspired superhydrophilic/underwater superoleophobic surfaces with robust wax-prevention, self-cleaning and oil/water separation function

Facile Fabrication of the Durable Micro/nano-Superhydrophilic/superoleophobic Surface Through One-Step Spraying for Efficient Oil–water Separation

Air superhydrophilic-superoleophobic SiO2-based coatings for recoverable oil/water separation mesh with high flux and mechanical stability

One-step fabrication of coating-free mesh with underwater superoleophobicity for highly efficient oil/water separation

Bioinspired Structured Superhydrophobic and Superoleophilic Stainless Steel Mesh for Efficient Oil-Water Separation

A Cross-Linked Coating Decorated Mesh Prepared by Brush-Painting Method for Oil-in-water Emulsions Separation

Facile Fabrication of Versatile Superhydrophobic Coating for Efficient Oil/water Separation

Facile Design of a Stable and Inorganic Underwater Superoleophobic Copper Mesh Modified by Self-Assembly Sodium Silicate and Aluminum Oxide for Oil/water Separation with High Flux.

Synthesis of Si-Based High-Efficiency and High-Durability Superhydrophilic-Underwater Superoleophobic Membrane of Oil–Water Separation

Superhydrophilicity and Underwater Superoleophobicity Graphene Oxide-Microcrystalline Cellulose Complex-Based Mesh Applied for Efficient Oil/water Separation