Abstract:Concrete-filled steel tubes (CFST) incorporating high-strength steel (HSS) could produce more efficient structural system with lighter weight and higher capacity. However, the design methods for applying concrete-filled highstrength steel tubes (CFHST) are not available yet and limited investigations had been reported. In this research, 8 full scale mid-slenderness circular CFHST specimens, made of innovative high-performance Q460qENH structural steel with actual yielding stress fy as high as 530 MPa, were tested subject to axial and eccentric compression. The main parameters considered in the experimental program included: (a) infilled concrete strength fc' = 39.8-75.3 MPa and (b) loading eccentricity ratio e/D = 0-0.3. The numerical model for CFHST was established and validated with load-displacement curves, failure modes and neutral axis locations obtained from the 8 experiments. The numerical models were further validated in capacity predictions with 232 axial compressions and compression-bending CFHST experimental data collected from the literature, proved to be generally applicable with fy = 435-835 MPa, xi = 0.5-8.5 and lambda n = 0.07-1.90 in both circular and square sections. Based on the validated numerical models, total 526 simulations were performed to investigate the influence of: (a) higher yielding strength fy and thinner-walled steel tubes; (b) confinement factor xi and (c) normalized slenderness ratio lambda n, on the composite strength fsc and compression-bending (N-M) interaction behavior. Experimental and numerical investigations showed that high strength steel could further improve the CFST capacity with basically no reduction in safety margin and ductility performance, but was in need of design method modifications due to changes in composite mechanism. On this basis, an analytical refined plastic-section equilibrium model (RPE model) was proposed to derive practical N-M interaction design curve with consideration of strength enhancement due to the composition and actual stress distribution at ultimate state. The further proposed general design method for compression-bending CFHST included: (a) formulas of fsc-xi relationship; (b) validated formulas of pure-bending capacity and overall stability inherited from GB 50936; (c) practical design curves of N-M interaction considering the effect of xi and lambda n. By comparing with GB 50936, AISC 360, EC 4 and CECS 28 provisions, the proposed method provided more accurate solutions in capacity predictions of CFHST members.

Bending Capacity of Steel-Concrete-Steel Composite Structures Considering Local Buckling and Casting Imperfection

Investigation of the shear resistances of steel-concrete-steel composite structures with bidirectional webs

Improved Seismic Design Using Bolted End Plate Connections For Steel Reinforced Concrete Composite Structures

Experimental Investigation And Design Of Concrete-Filled Cold-Formed Thin-Walled Steel Tubes Subject To Bending

Global Stability Tests and Design of Multi-Celled Concrete-Filled Steel Tubular Walls

Experimental Study of Innovative Steel-Concrete Composite Beams under Hogging Moment

Selected Series Method on Buckling Design of Stiffened Steel-Concrete Composite Plates

Stability Design of Multi-Celled Corrugated-Plate CFST Walls under Combined Axial and In-Plane Bending Loads

Experimental Investigation and Design of Thin- Walled Concrete-Filled Steel Tubes Subject to Bending

Flexural Tests and Behavior of Multi-Celled Corrugated-Plate CFST Members

Research on the Compression-Bending Behavior of Concrete-Filled Double-Steel-plate Composite Bridge Towers

The application of steel-concrete-steel composite structures in immersed tunnels

Experimental Study on Composite Steel- HSC Beams

Experimental and Numerical Investigations on Large-Scale Concrete-Filled Double-Steel-plate Composite Structures

Experimental and Theoretical Studies on the Shear Resistance of Steel–Concrete–Steel Composite Structures with Bidirectional Steel Webs

Flexural behavior of prefabricated high-strength steel-concrete composite beams with steel block connectors

Behavior and General Design Method of Concrete-Filled High-Strength Steel Tube (CFHST) Columns

Local and post-local buckling of fabricated high-strength steel and composite columns

Experimental Studies on the Cooperative Performance of Steel- Concrete Composite Large-span Bridge Tower

Experiment and finite element analysis of bending behavior of high strength steel-UHPC composite beams

Shear Performance of Single Steel-Plate Concrete Composite Beams with Various Transverse Reinforcement Configurations