Abstract:Recently, the polymer solar cells (PSCs) based on the PM6 and small molecular acceptor (SMA) Y6 have attracted considerable attention in this community for their outstanding photovoltaic performance. As well known, the molecular weight of polymer has dramatic impact on the blend morphology and photovoltaic performance in the polymer solar cells, especially for those polymers with temperature‐dependent aggregation (TDA) behavior. In this work, a series of PM6 polymers with different weight‐average molecular weights (Mw= 41, 67, 74, 84 and 114 kDa) were synthesized, and the effects of the Mw on the morphology and photovoltaic performance were systematically investigated. Notably, tuning the molecular weight induces dramatic influences on the aggregation behaviors of the polymers and their corresponding blend morphology, which were explored by the temperature‐dependent UV‐vis absorptions (TD‐Abs), grazing incidence wide‐angle X‐ray scattering (GIWAXS) and resonant soft X‐ray scattering(R‐SoXS) measurements. Increasing Mw promoted the strong face‐on molecular packing and reduced the blend film domain sizes for enhanced donor‐acceptor interfacial areas, resulting in increased short‐circuit current densities (Jsc) and fill factor (FF). However, polymer donor with high Mw value processed stronger tendency of forming excessive pure donor aggregate, which hampered forming the intermixed phase for efficient charge transport, resulting in the inferior FF. Therefore, the optimized OSCs based on PM6 with moderate molecular weight (Mw=74 kDa) and Y6 exhibited suitable size and purity of the domains, facilitating well‐balanced charge transport, reducing trap‐assisted recombination and leading to significant enhancement of photovoltaic performance with the optimal PCE of 17.1%. This work indicates that proper and precisely tuning the molecular weight of polymer donor is critical to enhance the photovoltaic performance in PSCs.This article is protected by copyright. All rights reserved.

Morphology Optimization Via Molecular Weight Tuning of Donor Polymer Enables All-Polymer Solar Cells with Simultaneously Improved Performance and Stability

Optimizing the Morphology of All-Polymer Solar Cells for Enhanced Photovoltaic Performance and Thermal Stability

Morphology Optimization Via Side Chain Engineering Enables All Polymer Solar Cells with Excellent Fill Factor and Stability

Tuning Aggregation Behavior of Polymer Donor via Molecular‐Weight Control for Achieving 17.1% Efficiency Inverted Polymer Solar Cells

Improving Performance of All‐Polymer Solar Cells Through Backbone Engineering of Both Donors and Acceptors

In Situ Monitoring Drying Process to Disclose the Correlation Between the Molecular Weights of a Polymer Acceptor with a Flexible Spacer and the Performance of All-Polymer Solar Cells

Morphology-performance relationships in high-efficiency all-polymer solar cells

Fine Tuning Miscibility of Donor/Acceptor through Solid Additives Enables All‐Polymer Solar Cells with 15.6% Efficiency

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

High‐Performance Binary All‐Polymer Solar Cells with Efficiency Over 18.3% Enabled by Tuning Phase Transition Kinetics

Efficient Non-Halogenated Solvent Processed Ternary All-Polymer Solar Cells with A Favorable Morphology Enabled by Two Well-Compatible Donors.

High-Performance All-Polymer Solar Cells and Photodetectors Enabled by a High-Mobility n-Type Polymer and Optimized Bulk-Heterojunction Morphology

Backbone regulation of a bithiazole-based wide bandgap polymer donor by introducing thiophene bridges towards efficient polymer solar cells

Morphology control by tuning electrostatic interactions for efficient polythiophene-based all-polymer solar cells

Polymer Pre‐Aggregation Enables Optimal Morphology and High Performance in All‐Polymer Solar Cells

Aggregation‐Induced Multilength Scaled Morphology Enabling 11.76% Efficiency in All‐Polymer Solar Cells Using Printing Fabrication

High Performance All-Polymer Solar Cells by Synergistic Effects of Fine-Tuned Crystallinity and Solvent Annealing.

Modulating the nanoscale morphology on carboxylate-pyrazine containing terpolymer toward 17.8% efficiency organic solar cells with enhanced thermal stability

Reducing steric hindrance around electronegative atom in polymer simultaneously enhanced efficiency and stability of organic solar cells

Effect of polymer molecular weight and processing solvent on the morphology and photovoltaic performance of inverted non-fullerene solar cells

Controlling Molecular Weight to Achieve High-Efficient Polymer Solar Cells With Unprecedented Fill Factor of 79% Based on Non-Fullerene Small Molecule Acceptor