Abstract:Titanium carbide (TiC) particulates-reinforced iron matrix composites were prepared by in situ fabrication method combining an infiltration casting with a subsequent heat treatment. The effects of different heat treatment times (0, 1,6 and 11 h) at 1138 degrees C on the phase evolution, microstructural features, and properties of the composites were investigated. The as-prepared composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and microhardness and wear resistance tests. The XRD results showed that the composites consisted of graphite, alpha-iron and titanium carbide after heat treatment at 1138 degrees C for 11 h. The SEM observation revealed that the formed TiC particulates were homogenously distributed in the iron matrix. The average microhardness of the composite heat treated at 1138 degrees C for 6 h increased depending upon the region: 209 HV0.1 (iron matrix) <787 HV0.1 (titanium wire) < 2667 HV0.1 (composite region). After being heat treated at 1138 degrees C for 11 h, the composite indicated no considerable change in microhardness value, and the average microhardness of the composite region was about 2354 HV0.1. The highest microhardness value obtained for the composite region was due to the formation of titanium carbide particulates as reinforcement phase within the iron matrix. Relative wear resistance was determined by a pin-on-disc wear test technique under different loads, and as a result, the composites containing higher volume fraction of hard titanium carbide particulates presented higher wear resistance compared with the unreinforced gray cast iron. (C) 2011 Elsevier Ltd. All rights reserved.

Nano-sized TiN-reinforced Composites: Fabrication, Microstructure, and Mechanical Properties

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Mechanical properties and microstructure of TiN/TZP nanocomposites

Simultaneously Increasing the Strength and Ductility of Nano-Sized TiN Particle Reinforced Al–Cu Matrix Composites

Preparation and Mechanical Properties of Particulate-Reinforced Powder Metallurgy Titanium Matrix Composites

Microstructure of TiC particle reinforced titanium matrix composite

In Situ Formation of Ti Matrix Composites Reinforced Nanometric TiC by Powder Metallurgy Technique

The Effect of Micron-Sized TiB2 Particles on the Properties of Al6061 Strengthened with 4% TiB2 Nano-TiB2

CNTs/Cu-Ti Composites Fabrication Through the Synergistic Reinforcement of CNTs and in Situ Generated Nano-Tic Particles

Processing of Multi-Walled Carbon Nanotube-Reinforced Tini Composites by Hot Pressed Sintering

Characterization of Structure and Properties of TiN–TiB2 Nano-Composite Prepared by Ball Milling and High Pressure Heat Treatment

Fabrication of an In-Situ Ti-2.6vol%Tic Metal Matrix Composite by Thermomechanical Consolidation of A Tih2-1vol%Cnts Powder Blend

Synthesis Of Tin Nano-Composite Powder By High-Energy Ball Milling Of Tih2 Under Nitrogen Atmosphere

Rapid in-situ reaction synthesis of novel TiC and carbon nanotubes reinforced titanium matrix composites

Effects of nano-TiCp on the microstructures and tensile properties of TiCp/Al–Cu composites

Microstructure and Mechanical Properties of Cu Matrix Composites Reinforced by TiB2/TiN Ceramic Reinforcements

Microstructure and Mechanical Properties of in Situ Synthesised (Tic+tib)/ti-6Al-4v Composites Prepared by Powder Metallurgy

In Situ Fabrication of Titanium Carbide Particulates-Reinforced Iron Matrix Composites

Refined microstructure and ultrahigh mechanical strength of (TiN

Preparation and Properties of Titanium Diboride Ceramic Matrix Reinforced by Carbon Nanotubes