Abstract:Since thorium (Th) owns high conversion ratio in thermal neutron spectrum, high melting temperature, high thermal conductivity and good corrosion resistance in high-temperature water, it can be doped into UO2 based fuel to initiate the fission reaction, and improve the physical properties of UO2. Owing to the challenging experimental conditions and technologies, molecular dynamics (MD) simulations are conducted to investigate the influences of Th doping on the mechanical properties of U1–xThxO2. The phase transition from initial fluorite structure to the metastable scrutinyite phase when loading along the [001] direction is observed, which accords well with the previous density functional theory calculations. However, if U1–xThxO2 is loaded along the [111] direction, only brittle fracture is observed. It is found that both the elastic modulus and fracture stress decrease linearly with elevating temperature but the fracture strain increases. As the Th concentration increases from 0 to 0.55, the elastic modulus first decreases and then increases; if the Th concentration is larger than 0.1, the fracture stress increases and the fracture strain decreases monotonically. The cracks are nucleated with an angle of 45º to the loading direction, propagate rapidly, and are characteristic of brittle fracture, which accords well with the classical failure criteria and experimental results for brittle materials. By comparison, the uniaxial tensile loading is also performed for polycrystalline U1–xThxO2. It is found that the elastic modulus and fracture stress decrease as the temperature increases. However, the elastic modulus is not sensitive to the Th concentration and the fracture increases as the Th concentration increases. The brittle intergranular fracture is observed in each of all polycrystalline samples. The obtained physical parameters are useful for designing the fuels in nuclear reactors.

Effect of burnup on the mechanical properties of doped UO2 ceramic pellets using the simfuel technique

Microstructure and Thermophysical Properties of Er2O3-doped UO2 Ceramic Pellets

Performance and properties evolution of near-term Accident Tolerant Fuel: Cr-doped UO 2

Mechanical behaviors of the dispersion nuclear fuel plates induced by fuel particle swelling and thermal effect II: Effects of variations of the fuel particle diameters

The high burn-up structure evolution in polycrystalline UO 2 : Phase-field modeling investigation

The Effect of Temperature and Burnup on U-10Zr Metallic Fuel Chemical Interaction with HT-9: a SEM-EDS Study

Effects of the Mesostructures and Irradiation Conditions on the Thermo-Mechanical Coupling Behaviors in LWR-used Fully Ceramic-Microencapsulated Fuel Pellets

Mechanical Behaviors of the Dispersion Nuclear Fuel Plates Induced by Fuel Particle Swelling and Thermal Effect I: Effects of Variations of the Fuel Particle Volume Fractions

Effects Of Th Doping On Mechanical Properties Of U1-Xthxo2: An Atomistic Simulation

ANALYSIS OF UO2-BEO FUEL PERFORMANCE DURING NORMAL CONDITIONS AND RIA

Modeling the Irradiation Swelling of UO2 at the Fuel Pellet Rim

Macro-Mesoscale In-Pile Thermal-Mechanical Behavior Simulation of a UMo/Zr Monolithic Fuel Plate

Detailed characterization of a PWR fuel rod at high burnup in support of LOCA testing

Effects of Th doping on mechanical properties of U<sub>1–</sub><i><sub>x</sub></i>Th<i><sub>x</sub></i>O<sub>2</sub>: An atomistic simulation

Investigation of swelling behaviors of U-10Zr metallic fuel in the low temperature regime via a cavitational void swelling model

Three-dimensional FE analysis of the thermal-mechanical behaviors in the nuclear fuel rods

Impact of High Porosity on Thermal Transport in UO_2 Nuclear Fuel

Investigation on Thermo-Mechanical Performance of Fully Ceramic Microencapsulated Fuel

Effects of Particle Volume Fraction on the Macro-Thermo-Mechanical Behaviors in Plate-Type Dispersion Nuclear Fuel Elements

Research on In-Pile Thermal-Mechanical Behavior of UMo/Zr Monolithic Fuel Plates

The critical influencing factors responsible for the particle cracking in UMo/Zr dispersion fuel plates during post-irradiation anneal tests