Abstract:Proton exchange membrane fuel cells (PEMFCs) as a promising clean energy conversion technology have gained considerable attention. However, the high cost and low durability of Pt-based nanocatalysts for the cathodic oxygen reduction reaction (ORR) hinder the wide adoption of this technology. 1 Despite great efforts on the development of advanced Pt-based catalysts to improve the Pt utilization and mass activity toward ORR, 2-3 their high activities/durability measured in liquid cells have rarely been realized in fuel cells. On the other hand, carbon-based Pt group metal (PGM)-free ORR electrocatalysts consisting of highly dispersed transition-metal single atoms in nitrogen-coordinated carbon surfaces (Me-N-C) are promising candidates to replace Pt. 4 Unfortunately, the poor durability of Me-N-C has limited their practical applications. 5 Some early studies 6-7 shown that Me-N-C as a support for Pt-based electrocatalyst could improve the stability of the latter. Herein, we report a hybrid electrocatalyst (denoted as Pt-Fe-N-C) consisting of Pt-Fe alloy nanoparticles on highly dispersed Pt and Fe single atoms in a nitrogen-doped carbon support (Figure 1a). The multiple types of active sites result in not only a 3.7 times higher Pt mass activity, but also excellent durability. The performance loss is negligible even after 100,000 potential cycles (Figure 1b), and no current drop is observed at 0.6 V in a fuel cell test with an ultra-low Pt loading (0.015 mg Pt cm −2 ) in the cathode. The morphology and structure of Pt-Fe-N-C catalyst after 100,000 cycles in a fuel cell were further analyzed. Abundant single atoms were still uniformly distributed on the carbon support. No noticeable aggregation of Pt-Fe nanoparticles was observed. Most of particle size was smaller than 4 nm, a solid PtFe@Pt core-shell structure was formed. Around 7% large size particles formed a percolated structure. This work highlights the importance of the synergistic effects among different active sites in hybrid electrocatalysts and provide an alternative way to design more active and durable low-PGM electrocatalysts for fuel cells and other electrochemical devices. This work was supported by the Research Grant Council (HKUST C6011-20G) and Shenzhen Science and Technology Innovation Committee (SGDX2019081623340748). Figure 1. (a) Scanning transmission electron microscope image (the spots in the blue and red dashed circles are ascribed to the Fe and Pt single atoms, respectively). (b) H 2 /O 2 fuel cell polarization (solid symbols and left axis) and power density (hollow symbols and right axis) plots of the Pt-Fe-N-C cathode before cycling (blue) and after 100,000 potential cycles (red) between 0.6 and 0.95 V. Figure 1

Monodispersed Pt3Ni Nanoparticles As a Highly Efficient Electrocatalyst for PEMFCs

Highly Active Nanoporous Pt-based Alloy As Anode and Cathode Catalyst for Direct Methanol Fuel Cells

Boosting Electrocatalytic Activities of Pt-Based Mesoporous Nanoparticles for Overall Water Splitting by a Facile Ni, P Co-Incorporation Strategy

Engineering Porosity into Trimetallic PtPdNi Nanospheres for Enhanced Electrocatalytic Oxygen Reduction Activity

PtFe Nanoalloys Supported on Fe‐Based Cubic Framework as Efficient Oxygen Reduction Electrocatalysts for Proton Exchange Membrane Fuel Cells

Synergistic effect of Pt-Ni dual single-atoms and alloy nanoparticles as a high-efficiency electrocatalyst to minimize Pt utilization at cathode in polymer electrolyte membrane fuel cells

Ultrathin Ni–N–C layer modified Pt–Ni alloy nanoparticle catalysts for enhanced oxygen reduction

Electrospun bimetallic PtNi nanowires as electrocatalyst for oxygen reduction reaction in PEMFCs

Enhanced Catalytic Activities of NiPt Truncated Octahedral Nanoparticles Toward Ethylene Glycol Oxidation and Oxygen Reduction in Alkaline Electrolyte.

Mixed‐Dimensional Pt‐Ni Alloy Polyhedral Nanochains As Bifunctional Electrocatalysts for Direct Methanol Fuel Cell

Patchy Fe-N-C Supported Low-Loading Pt Nanoparticles As a Highly Active Cathode for Proton Exchange Membrane Fuel Cells

Pt0.61Ni/C for High-Efficiency Cathode of Fuel Cells with Superhigh Platinum Utilization

Electronic Enhancement Engineering by Atomic Fe–N4 Sites for Highly‐Efficient PEMFCs: Tailored Electric‐Thermal Field on Pt Surface

Atomically Dispersed Single Metal Sites for Promoting Pt and Pt3Co Catalysts in Heavy-Duty Meas

Highly dispersed ultrafine PtCo alloy nanoparticles on unique composite carbon supports for proton exchange membrane fuel cells

Optimization of Pt-Ni Alloy Catalysts Synthesized by Potentiostatic Electrodeposition for Cathode in PEMFC

Solution-plasma interaction for synthesizing highly active Pt–Ni alloy oxygen reduction nanocatalysts for PEMFCs

High Oxygen Reduction Activity of Pt-Ni Alloy Catalyst for Proton Exchange Membrane Fuel Cells

Atomically Dispersed Pt and Fe Sites and Pt-Fe Nanoparticles for Durable Proton Exchange Membrane Fuel Cells

Electrocatalytic performance of sonochemically synthesized Pt–Ni/C nanoparticles in fuel cell application

Synthesis of Ultrathin and Composition-Tunable PdPt Porous Nanowires with Enhanced Electrocatalytic Performance