Abstract:Spray cooling, which has a fast thermal response and low flow rate consumption, is a common and effective thermal management approach for high power electronic systems. Typically, to improve the heat transfer co-efficient (HTC) for spray cooling, the target surface wettability is decreased, promoting nucleation boiling by reducing the surface energy barrier for bubble nucleation. However, the merging of bubbles and the formation of a vapor film have limitations in further increasing the critical heat flux (CHF). Hence, maximizing both the HTC and CHF of spray cooling can be mutually exclusive on the same heated surface. This paper presented a novel design for a vapor-liquid separation structure surface. It consisted of lower micropillars that serve as the vapor separation channel. On top of that, there was an upper multi-layer copper micromesh that wicks and spreads the coolant. Additionally, nano-grass attached to the micromesh to enhance capillary force and increase the nucleation sites simultaneously. Subsequently, we calculated the forward velocity and pressure drop of the droplets passing through the copper mesh to study the effects of droplet velocity and capillary force on heat transfer performance. The results show that the forward velocity of the droplets decreases rapidly as the increase of copper mesh layers and it drops to zero when passing through the third mesh. Therefore, the capillary force generated by the copper mesh is another important factor for the atomized droplets to pass through the copper mesh and reach the target surface. We have proven that all the vapor-liquid separation structure surfaces satisfy the condition Delta Pcap>Delta Ppore+Delta Plocal. Hence, the synergistic effects of the micropillar, copper micromesh, and nano-grass enable a circulation process of wicking-rewetting-vapor evacuation, which improves the onset of nucleate boiling (ONB), enhances the HTC, and increases the maximum heat flux dissipated by the system. Enhanced HTC (7.94 W/cm2/K) and maximum heat flux (817 W/cm2) were achieved at 1.50 ml/s on the vapor-liquid separation structure surfaces (#200 2-layer), representing an enhancement of 79.6% and 80.0% compared with that for the flat surface and the temperature of the heated surface at the ONB maximum decreased by approximately 30.8 degrees C.

Heat Transfer Enhancement Due to Surface Modification in the Close-Loop R410A Flash Evaporation Spray Cooling

Experimental Investigation of Spray Cooling Performance in Non‐boiling Zone on Rough Superhydrophilic/hydrophobic Surfaces

Enhancement of Heat Transfer on Micro- and Macro- Structural Surfaces in Close-Loop R410A Flashing Spray Cooling System for Heat Dissipation of High-Power Electronics

Investigation of Macro-fin Structure on Heat Transfer Performance of Close-Loop R410A Flashing Spray Cooling

Heat Transfer Performance and Optimization of a Close-Loop R410A Flash Evaporation Spray Cooling

Coupling dynamic thermal analysis and surface modification to enhance heat dissipation of R410A spray cooling for high-power electronics

Experimental Study on a Spray and Falling-Film Cooling System

Parametric Investigation on the Close-Loop R410A Flash Spray System for High Power Electronics Cooling under Low Temperature

Experimental Study on Combined Heat Transfer Enhancement Due to Macro-Structured Surface and Electric Field During Electrospray Cooling

Experimental Investigation on Heat Transfer Characteristics of R1336mzz Flash Spray Cooling

Heat transfer enhancement of spray cooling by copper micromesh surface

Boiling and quenching heat transfer advancement by nanoscale surface modification

Heat Transfer Optimization of R134a Phase Change Spray Cooling in a Closed Loop System

Spray Cooling on Enhanced Surfaces: A Review of the Progress and Mechanisms

Experimental and computational investigation on synergistic enhancement spray cooling using micropillars and capillary-driven wicking hybrid structures

Enhanced Heat Spray Cooling with a Moving Nozzle

Effects of Surface Structures on Critical Heat Flux in Spray Cooling

Record-high Heat Transfer Performance of Spray Cooling on 3D-Printed Hierarchical Micro/nano-Structured Surface

Experimental and Numerical Studies on the Spray Cooling of Deionized Water in Non-Boiling Regime

The Coupling Effect of Surface Vibration and Micro-structure on Spray Cooling Heat Transfer

Study on Moving Nozzle Effects on Spray Cooling of Electronics