Abstract:The trajectory and adhesion behavior of droplets inair-assisted pesticide spraying in greenhouse are closely related with several factors: the velocity field and pressure field of the airflow, the droplets properties (such as droplet size, initial velocity), the spraying angle, as well as the target parameters (such as shape, size and position). This study explored the conditions that influenced the droplets carried by airflow, with a keen emphasis on whether it could touch, instead of going around, and stay on the target. A CFD (computational fluid dynamics) model was introduced for droplet trajectory simulation in an airflow field, in which droplets were traced by discrete phase particle tracking method. A computation region of 1600, 720 and 1000 mm respectively in streamwise, spanwise and normalwise was established. A target with the dimension of 120 mm × 120 mm × 30 mm was placed 400 mm above ground and 840 mm away from the left boundary of the computational domain. To simplify computational complexity, only half of the computational region (1600 mm × 360 mm × 1000 mm) was computed since the whole region was symmetric on both sides of the sprayer in streamwise. The grid number of the actual computation domain was about 0.36 million. A local mesh encryption method was applied around the target in order to increase the resolution of the simulation. The particle diameters involved in this simulation were 10, 30, 40, 50, 60, 70, 80 and 100μm; and the injection angles were adjusted to 90°, 75°, 60°, 45°, 30° and 15° respectively. A discrete phase boundary condition was set which trapped the droplets on the ground (wall) or the target surfaces. The rest of boundaries for discrete phase were set to boundary condition of droplet escaping. The influences of droplet velocity, droplet size and injection angle on deposition rate were evaluated by the CFD simulation and the experiments proved that: the condition of a droplet touching and adhering on target was that the maximum moving time of droplets inx andy direction should be simultaneously longer than the maximum moving time of droplets inz direction in the region around the target. There was a region below the target where droplets could not reach while spraying, and the length of the region was related to spraying angle. The adhesion behavior of droplets was affected by air velocity and droplet size. When the droplet size was 50μm and spraying angle was 60°, the larger the spraying velocity, the lower the deposition rate. The comparison of the deposition rates from simulations and experiments proves that the experiment data agree well with the data from simulation, so the simulation can be taken as reliable and valid measure in droplet deposition evaluation under greenhouse condition.

Evaluation of Droplets Size Distribution and Velocity Pattern Using Computational Fluid Dynamics Modelling.

Numerical Simulation of Spray Drift and Deposition from a Crop Spraying Aircraft Using a CFD Approach

Evaluating Effective Swath Width And Droplet Distribution Of Aerial Spraying Systems On M-18b And Thrush 510g Airplanes

CFD simulation and validation of trajectory and deposition behavior of droplets around target affected by air flow field in greenhouse

Computational Fluid Dynamic Modeling Application As a Design Tool in Air Assisted Pesticide Sprayer Development

Analysis on Features of Air-velocity Distribution and Droplets Deposition Pattern for Greenhouse Air-assisted Mist Sprayer

Spray performance simulation and experiment analysis of a greenhouse fixed-pipe twin-fluid cold fogger with different nozzle settings

Three-Dimensional Simulation on Drift-reduction of Air-assist Spraying

CFD simulation and experiment of distribution characteristics for droplet of knapsack sprayer

Simulation and Validation of the Air Flow Generated by a Multi-Channel Air-Assisted Sprayer.

Numerical Simulation of Wake Vortices of Crop Spraying Aircraft Close to the Ground

Effects of operating conditions on droplet deposition onto surface of atomization impinging spray

Modeling and analysis of droplet deposition behavior: From the micro and macro perspectives

Influence of the Atmospheric Boundary Layer Stability on Aerial Spraying Studied by Computational Fluid Dynamics

3-D Numerical Simulation and Experiment of Air-velocity Distribution of Greenhouse Air-assisted Sprayer

Three-Dimensional Simulation Of Effervescent Atomization Spray

Analysis and validation of a CFD-DPM method for simulating dust suppression sprays

Theoretical study on atomizing model for target spray nozzle

A Fitting Formula for Predicting Droplet Mean Diameter for Various Liquid in Effervescent Atomization Spray

Internal mixing air-assisted spray nozzle for large droplets: Experimental measurements and numerical simulations

Numerical Simulation of Spray Flow Processes in Adjustable Centrifugal Nozzle