Abstract:In this study, the effects of surface modification on the physicochemical properties, degradation behavior, and cellular responses of poly(caprolactone) (PCL)/hydroxyapatite (HAp) scaffolds using carboxylated multi-walled carbon nanotubes (MWCNTs) were investigated. The scaffolds were prepared using the fused deposition modeling (FDM) technique, followed by aminolysis for 15, 30, and 60 minutes. Subsequently, the scaffolds were immersed in MWCNT solutions with concentrations of 0.1 %, 0.5 %, and 1 % g/mL to achieve the desired coating. Various characterization techniques were employed to evaluate the surface morphology, chemical composition, and structural changes induced by the coating. FESEM images revealed a uniform MWCNT coating on the PCL/HAp scaffolds at an optimal concentration of 0.5 % g/mL, while lower concentrations resulted in incomplete coating and higher concentrations led to MWCNT agglomerations. The MWCNT coating successfully enhanced the conductivity of the scaffolds, with electrical conductivity increasing from near zero for the non-coated PCL/HAp scaffolds to 5 × 10 −5 S/m for the MWCNT-coated scaffolds. Additionally, the coating exhibited improved wettability, as demonstrated by decreased water contact angles from 67.71° for non-coated surfaces to 51.50° for the MWCNT-coated surfaces. Furthermore, the in vitro degradation studies showed that HAp in the PCL matrix accelerated the hydrolysis rate, resulting in higher degradation rates for the PCL/HAp scaffolds than pure PCL scaffolds. The MWCNT coating further influenced the degradation behavior, with variations in degradation rates depending on the MWCNT concentration. Cell viability assays using MG-63 cells revealed improved cell viability and adhesion on the MWCNT-coated PCL/HAp scaffolds compared to plain PCL and PCL/HAp scaffolds. The cell viability increased from 84 % for plain PCL and 103 % for PCL/HAp to 109 % for the MWCNT-coated scaffolds. Moreover, FESEM images showed increased cell adhesion on the MWCNT-coated surfaces, with optimal adhesion observed on the scaffolds coated with 0.5 % g/mL MWCNTs. The results of this study highlight the potential of MWCNT coatings to improve the surface properties of PCL/HAp scaffolds, making them excellent choices for bone tissue engineering applications.

Zwitterionic PMCP-Modified Polycaprolactone Surface for Tissue Engineering: Antifouling, Cell Adhesion Promotion, and Osteogenic Differentiation Properties.

Engineering cartilage tissue based on cartilage-derived extracellular matrix cECM/PCL hybrid nanofibrous scaffold

Surface Modification of Polycaprolactone Scaffold With Improved Biocompatibility and Controlled Growth Factor Release for Enhanced Stem Cell Differentiation

Poly(ε-caprolactone) Modification Via Surface Initiated Atom Transfer Radical Polymerization with Bio-Inspired Phosphorylcholine.

Optimization of Poly(ε‐caprolactone) Surface Properties for Apatite Formation and Improved Osteogenic Stimulation

Improvement of Hemocompatibility of Polycaprolactone Film Surfaces with Zwitterionic Polymer Brushes.

Surface modification of polycaprolactone substrates using collagen-conjugated poly(methacrylic acid) brushes for the regulation of cell proliferation and endothelialisation

Surface Functionalization of Polycaprolactone Films Via Surface-Initiated Atom Transfer Radical Polymerization for Covalently Coupling Cell-Adhesive Biomolecules.

Surface Modification of Polycaprolactone Membrane Via Aminolysis and Biomacromolecule Immobilization for Promoting Cytocompatibility of Human Endothelial Cells.

Surface Modification of Polycaprolactone Membrane Via Layer-By-Layer Deposition for Promoting Blood Compatibility

Bioinspired Surface Functionalization for Improving Osteogenesis of Electrospun Polycaprolactone Nanofibers

Characterization on Modification and Biocompatibility of PCL Scaffold Prepared with Near-field Direct-writing Melt Electrospinning

Adhesion, intracellular signalling and osteogenic differentiation of mesenchymal progenitor cells and preosteoblasts on poly(epsilon)caprolactone films functionalized by peptides derived from fibronectin and/or BMP-9

Biomimetic Calcium Phosphate Coated Macro-Microporous Poly(ε-caprolactone)/Silk Fibroin (PCL/SF) Scaffold for Bone Tissue Engineering

Tailoring surface properties of Poly(caprolactone)/Hydroxyapatite scaffolds through aminolysis and multi-walled carbon nanotube coating for bone tissue engineering

Functionalization of the Surface of Electrospun Poly(Epsilon-Caprolactone) Mats Using Zwitterionic Poly(Carboxybetaine Methacrylate) and Cell-Specific Peptide for Endothelial Progenitor Cells Capture

Surface Modification of Poly(L-Lactic Acid) by Entrapment of Chitosan and Its Derivatives to Promote Osteoblasts-Like Compatibility

Enhancing bone regeneration with bionic hydrolysis and biomimetic polydopamine coating on 3D-printed PCL scaffolds: A comparative study

Biocompatibility of Poly(ε-caprolactone) Scaffold Modified by Chitosan—The Fibroblasts Proliferation in vitro

Microstructures and Properties of Polycaprolactone/tricalcium Phosphate Scaffolds Containing Polyethylene Glycol Fabricated by 3D Printing

Polycaprolactone in Bone Tissue Engineering: A Comprehensive Review of Innovations in Scaffold Fabrication and Surface Modifications