Abstract:Non-fullerene electron acceptors have attracted enormous attention of the research community owing to their advantages of optoelectronic and chemical tunabilities for promoting high-performance polymer solar cells (PSCs). Among them, fused-ring electron acceptors (FREAs) are the most popular ones with the good structural planarity and rigidity, which successfully boost the power conversion efficiencies (PCEs) of PSCs to over 14%. In considering the cost-control of future scale-up applications, it is also worthwhile to explore novel structures that are easy to synthesize and still maintain the advantages of FREAs. In this work, we design and synthesize a new electron acceptor with an unfused backbone, 5,5'-((2,5-bis((2-hexyldecyl)oxy)-1,4-phenylene)bis(thiophene-2-yl))bis(methanylylidene)) bis(3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimal-ononitrile (ICTP), which contains two thiophenes and one alkoxy benzene as the core and 2-(3-oxo-2,3-dihydroinden-1-ylidene) malononitrile (IC) as the terminal groups. The synthetic route to ICTP involves only three steps, with high yields. Density functional theory calculations indicate that the non-covalent interactions, O center dot center dot center dot H and O center dot center dot center dot S, help reinforce the space conformation between the central core and the terminals. ICTP shows broad and strong absorption in the long-wavelength range between 500 and 760 nm. The highest occupied molecular orbital and lowest unoccupied molecular orbital levels of ICTP were measured to be -5.56 and -3.84 eV by cyclic voltammetry. The suitable absorption and energy levels make ICTP a good acceptor candidate for medium bandgap polymer donors. The best devices based on PBDB-T:ICTP showed a PCE of 4.43%, with an open circuit voltage (V-OC) of 0.97 V, a short circuit current density (J(SC)) of 8.29 mA.cm(-2), and a fill factor (FF) of 0.55, after adding 1% 1,8-diiodooctane (DIO) as the solvent additive. Atomic force microscopy revealed that DIO could ameliorate the strong aggregation in the blended film and lead to a smoother film surface. The hole and electron mobilities of the optimized device were measured to be 9.64 and 2.03 x 10(-5) cm(2).v(-1).s(-1), respectively, by the space-charge-limited current method. The relatively low mobilities might be responsible for the moderate PCE. Further studies can be performed to enlarge the conjugation length by including more aromatic rings. This study provides a simple strategy to design non-fullerene acceptors and a valuable reference for the future development of PSCs.

Z-Shaped Fused-Chrysene Electron Acceptors for Organic Photovoltaics

Hybrid Nonfused Electron Acceptors with Perylene Diimide Pendants for Organic Solar Cells

Non-Fullerene Acceptor for Organic Solar Cells with Chlorination on Dithieno[3,2-b:2′,3′-d]pyrrol Fused-Ring

Synthesis and characterization of new nonfullerene electron acceptors with a chrysene core

Dithienopicenocarbazole-Based Acceptors For Efficient Organic Solar Cells With Optoelectronic Response Over 1000 Nm And An Extremely Low Energy Loss

Design of a Highly Crystalline Low-Band Gap Fused-Ring Electron Acceptor for High-Efficiency Solar Cells with Low Energy Loss

An Electron Acceptor With Broad Visible-Nir Absorption And Unique Solid State Packing For As-Cast High Performance Binary Organic Solar Cells

Nonfused Electron Acceptors Based on the 2D-Extended Quinoxaline Core for Organic Solar Cells

High-Performance Mid-Bandgap Fused-Pyrene Electron Acceptor

Fully-unfused electron acceptors based on a steric boron dipyrromethene (BODIPY) core for organic solar cells

Simple Non‐Fused Electron Acceptors Leading to Efficient Organic Photovoltaics

Fused Hexacyclic Nonfullerene Acceptor with Strong Near-Infrared Absorption for Semitransparent Organic Solar Cells with 9.77% Efficiency

Enhancing the Performance of Non-Fullerene Organic Solar Cells Via End Group Engineering of Fused-Ring Electron Acceptors

Precise Synthesis of Fused Decacyclic Electron Acceptor Isomers for Organic Solar Cells

Fused Tris(thienothiophene)-Based Electron Acceptor with Strong Near-Infrared Absorption for High-Performance As-Cast Solar Cells

High-Performance Electron Acceptor with Thienyl Side Chains for Organic Photovoltaics.

Fused Nonacyclic Electron Acceptors for Efficient Polymer Solar Cells

A Simple Electron Acceptor with Unfused Backbone for Polymer Solar Cells

Fused Octacyclic Electron Acceptor Isomers for Organic Solar Cells

Enhancement Of Intra- And Inter-Molecular Pi-Conjugated Effects For A Non-Fullerene Acceptor To Achieve High-Efficiency Organic Solar Cells With An Extended Photoresponse Range And Optimized Morphology

Synergistic Effects of Chlorination and Branched Alkyl Side Chain on the Photovoltaic Properties of Simple Non‐Fullerene Acceptors with Quinoxaline As the Core