Abstract:Because of the direct contact between the tire and pavement, the skid resistance of asphalt pavement is a basic factor affecting the braking safety of autonomous vehicles. The road skid resistance mainly depends on the texture characteristics of the road surface. Considering the pavement friction characteristics, building a braking model of autonomous vehicles is an effective method to improve the braking safety of autonomous vehicles. In order to develop the safety braking method for autonomous vehicles based on the road surface friction characteristic, an automatic close-range photogrammetry system (ACRP system) was proposed and built based on the circle arranged three cameras close-range photogrammetry (CRP) technology to obtain the asphalt pavement surface texture accurately in real time. Automatic image acquisition and 3D reconstruction were achieved by the ACPR system. Sand patch testing method and laser scanning method (ZGScan) were applied to collect the on-site asphalt pavement texture comparing with the results of ACRP system. It shows the texture data obtained by ACPR system have relatively high accuracy and efficiency with recognition accuracy close to 0.02 mm. Then, the peak adhesion coefficients under different road conditions were calculated by considering the skid resistance contribution of the road surface texture. Based on CarSim/Simulink joint simulation, a braking model for autonomous vehicles was established. The characteristics of the autonomous vehicles during straight normal braking, emergency braking and driving on curved sections were analyzed. Then, the safety braking distance under different conditions was put forward. The research shows that the variation trends of friction coefficient curves under different pavement conditions (dry and wet pavement) are basically the same, which both decrease significantly with the increase of relative slipping ratio. When the speed exceeds 40 km/h, the curve tends to be gentle, indicating that the actual contact area of the tire-road comes to a stable status when the speed is relatively high. Based on the tire hydroplaning model built by ABAQUS, the peak adhesion coefficient curves for different pavement conditions were obtained. It can be seen that the peak adhesion coefficient of the road surface is convex parabolic distribution at different driving speeds. Moreover, the peak adhesion coefficient gradually decreases as the speed increases. During normal braking, the vehicle should keep relatively low braking deceleration considering passenger comfort. As for emergency braking, autonomous vehicle should be equipped with professional short-range radar, long-range radar and high-definition camera to detect the environment surrounding the vehicle. On rainy days, the braking distance is averagely increased by about 45% compared to sunny days. When the braking distance between vehicles is large enough, it is recommended to brake with a braking force of 4−6 MPa. Autonomous vehicles should keep a certain safe distance, which requires 1.1−1.2 times of the simulated average value of safety braking distance during the driving process on dry or wet pavement. As the radius of curved sections increases, the acceleration interference values under different road conditions basically reduce. When the radius is greater than or equal to100 m, the decrease rate of the acceleration interference value is more significant. In order to improve the braking comfort of the vehicles, the radius of the curved road should be controlled above 100 m. In this paper, the safety strategies for autonomous vehicles considering pavement surface texture characteristics can provide references for the theoretical design of braking system and braking safety evaluation for autonomous vehicles.

A High Efficiency Aircraft Anti-Skid Brake Control with Runway Identification

Emergency Braking Control Strategy for High Speed Electric Drive Tracked Vehicle

A novel aircraft brake disturbance recognition model

A Real-Time Maximum Tire-Road Friction Tracking Control Method for Aircraft Braking System With Disturbance Compensation

MSD-Based NMPC Aircraft Anti-Skid Brake Control Method Considering Runway Variation

Robust Self-Learning PID Control of an Aircraft Anti-Skid Braking System

Application of Model Free Control Technology on the Aircraft Anti-skid Brake Systems

Design of ABS sliding mode control system for in-wheel motor vehicle based on road identification

A Hierarchical Road Identification Method for ABS Control

Theory and methodology on safety braking of autonomous vehicles based on the friction characteristic of road surface

Estimation of Road Friction Coefficient in Different Road Conditions Based on Vehicle Braking Dynamics

A method determining critical operating parameters for landing aircraft based on runway pavement skid resistance

Tire-road friction estimation and uncertainty assessment to improve electric aircraft braking system

Skid resistance in pavement-vehicle interaction with anti-lock braking systems

Road Friction Estimation under Complicated Maneuver Conditions for Active Yaw Control

Autonomous Emergency Braking Based on Radial Basis Function Neural Network Variable Structure Control for Collision Avoidance

Slip ratio control based on adaptive fuzzy sliding mode for vehicle with an electromechanical brake system

Research on Estimation Method for Airport Runway Friction Coefficient Based on Numerical Analysis

Nonlinear wheel-slip dynamics of battery electric vehicle for anti-lock brake system control by traction motor

Modeling aircraft braking performance on wet and snow/ice-contaminated runways

Optimal Slip Ratio Tracking Integral Sliding Mode Control for an EMB System Based on Convolutional Neural Network Online Road Surface Identification