Abstract:In this paper, a model of flood area display and damageevaluation is discussed, which adopts seed spread algorithm to calculate and visualize flood area based on a DEM data set and under the condition of a given water level of flood. The raster image containing flood area is overlaid with raster data converted from thematic vector maps such as land-use map and related to other socio-economic data, and then quantitative evaluation of flood damage is achieved. There are two different cases, the so-called “non-source flood” and “source flood”, for determining flood area based on DEM and under the given water level condition. Non-source flood corresponds to the case with well-distributed and large-area rainfall where all the low-lying land may have a flood disaster, and in this case all the points with elevations below the given water level should be included in the flood area. The “source flood” is the case of flood (e.g. from bank burst) flushing through the surrounding lands that needs to consider “ci rculating” condition. Because flood may be obstructed by ring structures or high lands, thus it can only cover the place where it flows and reaches. One of the computer processing methods suitable for source flood is the seed-spread algorithm. The principle of this method is to select a representative pixel as a seed and to examine its contiguous pixels outward along 4 or 8 directions. The pixels, contiguous to it and meeting the given conditions, become seeds, and then contiguous pixels to the new seeds will be examined in the same way. This process repeats until an aggregation of the pixels which meet the given conditions on a certain plane are obtained. Adopting seed spread algorithm for source-flood area calculation is just to achieve an aggregation of pixels, which satisfies the connectivity requirement and the given conditions of water level. The initial position of seed pixel should usually be selected on the characteristic points, e.g. adjacent to a reservoir dam or stream boundary. The precision of flood area calculation is mainly determined by spatial resolution of the DEM, the area on the ground is represented by each pixel; whereas the accuracy of flood area calculation, to a great extent, is dependent on the preci sion of the DEM's pixel value or elevation.Once the area below the flood water level has been calculated, the flood damage evaluation can be calculated by overlaying the flood range with thematic maps and by relating to other socio-economic data. All thematic maps were converted to raster data because algorithm of the overlay analysis implemented in raster format is relatively simple and computing is fast. In order to improve accuracy of the flood damage evaluation it is necessary to accurately register and georefer all raster layers before overlay analysis. The calculation results of flood damage evaluation are generally represented by tabulation, which is a kind of classified statistics of flood damage data, e.g. a table representing total area of every land-use type in different administrative divisions. The results of flood area calculation and damage evaluation can also be visually and dynamically provided in the forms of graph, image, 3D or virtual reality. The model has been successfully applied in the “Zhejiang Provincial Water Conservancy Management System” developed for a national project.

A Quantitative Flood-Related Building Damage Evaluation Method Using Airborne Lidar Data And 2-D Hydraulic Model

A GIS-based Method for Flooded Area Calculation and Damage Evaluation

Integrated Detection and Analysis of Earthquake Disaster Information Using Airborne Data

Visualization and Damage Assessment for Flooded Area

A Two-dimensional Numerical Model of Urban Flood Based on Building Density Coefficient

Flood Area and Damage Estimation in Zhejiang, China

A GIS Based Model for Calculating of Flood Area

Approach of Building Content Damage Assessment and Risk Quantification by Urban Local Flooding Based on GIS

Fine‐scale damage assessment of urban flooding based on the 1D/2D coupled hydrodynamic model

Micro-scale Flood Hazard Assessment Based on Catastrophe Theory and an Integrated 2-D Hydraulic Model: A Case Study of Gongshuangcha Detention Basin in Dongting Lake Area, China

Dam-break Flood Loss Assessment in Hurricane-Prone Regions

Application of LiDAR UAV for High-Resolution Flood Modelling

Post-earthquake assessment of building damage degree using LiDAR data and imagery

A Mathematical Model For Flood Loss Estimation Based On Spatial Grid

Geomatic-Based Flood Loss Assessment and Its Application in an Eastern City of China

An Improved Fineness Flood Risk Analysis Method Based on Digital Terrain Acquisition

Integrated Remote Sensing Imagery and Two-Dimensional Hydraulic Modeling Approach for Impact Evaluation of Flood on Crop Yields

Improving the Accuracy of Urban Waterlogging Simulation: A Novel Computer Vision-Based Digital Elevation Model Refinement Approach for Roads and Densely Built-Up Areas

An urban DEM reconstruction method based on multisource data fusion for urban pluvial flooding simulation

Identification of Building Damage from UAV-Based Photogrammetric Point Clouds Using Supervoxel Segmentation and Latent Dirichlet Allocation Model

Surface damage quantification of postearthquake building based on terrestrial laser scan data