Abstract:Abstract Emulsions flow is encountered in various pratical applications such as enhanced oil recovery (EOR) processes. The occurence of emulsions can have a detrimental impact on well productivity/injectivity and hence, on the enconomic of many EOR operations. However there is still a lack of clear understanding of how they really behave inside a porous medium. The present work aims at given new insights into emulsion deposition mechanisms. Different experimental conditions are explored to study the deposition of "stable" oil-in-water (O/W) emulsions inside a porous material. Porous media made of sharp-edged Silicon Carbide (SiC) grains of 80 μm in diameter and dilute and stable dodecane emulsions in brines were used. The ratio of pore to particle size (jamming ratio) is set high enough to ensure in-depth propagation and hence, an in-depth deposition on pore surface without any other retention mechanism such as straining and plugging. In this study, the effects of salinity and flow rate on droplet deposition are highlighted. At low salinities, the deposition and the induced permeability reduction are negligible. As SiC is negatively charged, this indicates that oil droplets bear a negative surface charge, even if they are stabilized by a non-ionic surfactant. Increasing the salinity induces a better deposition efficiency and a concomittant increase in permeability reduction by screening surface charges. Moreover, the piston-like displacement of the emulsion front entails that the available surface of each section is almost entirely saturated before the next one is reached. Thereby, the deposition is almost uniform along the core. The breakthrough curves exhibit a delay that increases while increasing the salinity and a plateau value near saturation (C/C0=1). This reveals two different deposition steps characterized by two depositon kinetics which will be described according to well known scaling power law for colloidal spheres. At high salinity and at the lowest flow rates (in the convection-regime), the maximum permeability reduction reached is in excellent agreement with the predicted value from Random Sequential Adsorption (RSA) model. That was initially developed for hard spheres. That confirms that, for "stable" O/W emulsions, droplets deposit as a single layer probably because of steric hindrance. Interestingly, the permeability reduction reaches its maximum at breakthrough where the surface coverage is close to 54%, as predicted from the RSA theory. However, although the permeability impairment is in agreement with the RSA theory, the total deposited amount of oil is higher than expected from the RSA model predictions. After the breakthrough, the droplet deposition continues increasing but at a very small rate during the aforementioned second deposition step, and this, with no significant impact on permeability. It infers that the deposit may get denser on grain surface owing to droplets distortion. The final surface coverage is thus higher than the upper limit depicted in the RSA theory. Finally, from the desorption and the mean hydrodynamic thickness of the deposition layer, we get some experimental clues that, the droplets are likely to deposit individually and not to coalesce to form a film. Introduction In the oil industry, emulsion flow and retention have attracted a growing interest since 30 years as they are involved in many oil production operations. Several models (Mc Auliffe, C. D., 1973; Devereux, O. F., 1974; Alvarado, D. A. and al, 1979) have been developed over the years but none of them describes the whole damaging process caused by emulsions (Rey, C. and al., 2000). The most accurate and reliable model is based on the deep-bed filtration (Soo, H. and al, 1986) and accounts for the residual permeability reduction and the shape of the breakthrough curve.

Stability of particle laden interfaces of drops flowing through a pore

Directional Transport of a Liquid Drop between Parallel-Nonparallel Combinative Plates.

Creating High Yield Stress Particle-Laden Oil/Water Interfaces Using Charge Bidispersity

Self-assembled nanoparticle-coated interfaces: Capillary pressure, shell formation and buckling

Drop impact dynamics on slippery liquid-infused porous surfaces: influence of oil thickness

Exudation behavior and pinning effect of the droplet on slippery liquid-infused porous surfaces (SLIPS)

Lifetime of oil drops pressed by buoyancy against a planar interface: Large drops

Disjoining pressure analysis of the lubricant nanofilm stability of liquid-infused surface upon lubricant depletion

Dewetting of Thin Lubricating Films Underneath Aqueous Drops on Slippery Surfaces

Equilibrium and stability of two-dimensional pinned drops

Emulsification of particle loaded drops in simple shear flow

Stability of liquid film coating a horizontal cylinder: interplay of capillary and gravity forces

Transition of Liquid Drops on Microstructured Hygrophobic Surfaces from the Impaled Wenzel State to the "Fakir" Cassie-Baxter State

How surface roughness affects the interparticle interactions at a liquid interface

Buckling in Armored Droplets

Dynamics of Droplets Moving on Lubricated Polymer Brushes

Emulsion Deposition in Porous Media: Impact on Well Injectivity

Control of Particle Adsorption for Stability of Pickering Emulsions in Microfluidics.

Physical mechanisms for droplet size and effective viscosity asymmetries in turbulent emulsions

Coalescence dynamics of sessile and pendant liquid drops placed on a hydrophobic surface

Formation of surface nanodroplets under controlled flow conditions