Abstract:To ensure the transition of the global energy system to a sustainable one, and to meet emission reduction targets of national climate policies we need in future to produce large amounts of “green” hydrogen. This will be necessary to sustain the world’s need for synthesis of “green” ammonia, “green” methanol and “green” jet fuels, but also for use in form of hydrogen as a transportation fuel and a reduction agent in steel making. Various electrolysis technologies for providing this hydrogen via an electrochemical splitting of water/steam are likely to become the backbone of this emerging sector. Among the different electrolysis technologies, available or under development, SOEC stands out with distinct advantages related to the high temperature of operation, most markedly; 1) there is no need for precious metals in the electrodes, and 2) the achievable efficiency is higher than for the other electrolysis technologies. The electrical efficiency may exceed 90 % as the technology can be run thermo-neutrally producing no waste heat, or may even utilize waste heat if such exist for instance from a down-stream upgrading of the hydrogen to methanol or ammonia. In view of these very significant advantages, SOEC is likely to become a key enabling technology for the above described transition. However, the SOEC technology is less mature than alkaline electrolysis and PEM-based electrolysis and is today deployed much less than the other two technologies. The largest SOEC units manufactured/operated today are in the range of ~1 MW. However, numerous scale up projects have recently been announced and the industrial stakeholders are these years investing massively to bring up production capacity and module sizes. In this paper we shall discuss some of the challenges in upscaling SOEC and some of the materials issues to be addressed, when considering large scale global deployment over the next decades. The inherent brittle nature of the ceramics used in the cells has so far limited the size of the cells of most stakeholders to be in the range with side-lengths from 10 to 15 cm. Ideally, in terms of upscaling module sizes, this should be much larger. This however requires great care in the manufacturing, and a tough and strong backbone material in the cell. Most stakeholders rely on stabilized zirconia to provide the structural support. Use of zirconia in the transformable (metastable) tetragonal version with 2 – 4 % Y 2 O 3 substitution holds some advantages over the use of the fully stabilized cubic version with ~8 % Y 2 O 3 , as the former has much higher strength/toughness. We shall present our recent results on optimizing composition and processing routes to maximize toughness and strength, whilst preventing unintended spontaneous transformation to the monoclinic phase during use, and shall discuss the consequences in terms of upscaling cell foot-print. In SOEC one does not need any precious metals (PGM-materials). However, typically the state of the art cells relies on use of several critical raw materials. Several rare earth materials (HREE/LREE) are used (Ce, Gd, Y, La) and also some critical transition metals like Co/Mn and Ni. Ni is by EU not considered critical, but is on the list of strategic materials. For large-scale deployment, it is obviously an advantage if the use of Critical Raw Materials (CRM) can be minimized. Introducing performance improvement in terms of increased production capacity per m 2 of cell or kg of material is a straightforward strategy to reduce the CRM-use of the technology and is likely a part of the strategy among all stakeholders. Endeavors to reduce the use of one particular material are also meaningful in such a materials resource perspective. We shall here present recent results on activities to increase the competitiveness of the SOEC technology by introducing a metal-support as the structural backbone and replace the Ni/YSZ-fuel electrode with one based on a mixed conducting Ti-based oxide (Ni and Fe-doped (La,Sr)TiO 3 ). Recently, we have found that such a material combination can in fact sustain SOEC operation for extended periods (tested over 5000 hr) at technologically relevant hydrogen production rates corresponding to current densities of 0.5 A/cm 2 . The results shall be presented and the possibilities to improve the titanate backbone further by compositional changes shall be discussed with special view to eliminating use of HREE/LREE and critical raw materials in general. Finally, we shall present some recent results on how to eliminate the use of Co in the oxygen electrode. The achieved results shall be compared with other approaches adopted in literature on how to eliminate use of Co and even La in the oxygen electrode.

An eco-technoeconomic analysis of hydrogen production using solid oxide electrolysis cells that accounts for long-term degradation

A techno-economic appraisal of hydrogen generation and the case for solid oxide electrolyser cells

Multi-objective Optimizations of Solid Oxide Co-Electrolysis with Intermittent Renewable Power Supply Via Multi-Physics Simulation and Deep Learning Strategy

Optimization of Solid Oxide Electrolysis Cells Using Concentrated Solar-Thermal Energy Storage: A Hybrid Deep Learning Approach

Advancements, strategies, and prospects of solid oxide electrolysis cells (SOECs): Towards enhanced performance and large-scale sustainable hydrogen production

Technological development of hydrogen production by solid oxide electrolyzer cell (SOEC)

Cost analysis of hydrogen production by high-temperature solid oxide electrolysis

Optimization of Integrated Solid Refuse Fuel and Solid Oxide Electrolyzer Cell System for Hydrogen Production

Techno-economic analysis of solar hydrogen production via PV power/concentrated solar heat driven solid oxide electrolysis with electrical/thermal energy storage

Techno-economic analysis and Monte Carlo simulation of green hydrogen production technology through various water electrolysis technologies

Properties of cathode-supported solid oxide electrolysis cells for hydrogen production

A Solid Oxide Electrolysis Cell (SOEC) with High Current Density and Energy Efficiency for Hydrogen Production

Solid Oxide Electrolysis of H2O and CO2 to Produce Hydrogen and Low-Carbon Fuels

Accelerated degradation for solid oxide electrolysers: Analysis and prediction of performance for varying operating environments

Electrochemical performance and microstructural characterization of solid oxide electrolysis cells

A Techno-Economic Study of Photovoltaic-Solid Oxide Electrolysis Cells Coupled Magnesium Hydrides-based Hydrogen Storage and Transportation Toward Large-Scale Applications of Green Hydrogen

System level heat integration and efficiency analysis of hydrogen production process based on solid oxide electrolysis cells

Energy and Exergy Analysis of Solid Oxide Electrolyser Cell (SOEC) Working As a CO2 Mitigation Device

A techno-economic model of a solid oxide electrolysis system

A Techno-Economic Study of Photovoltaic-Solid Oxide Electrolysis Cell Coupled Magnesium Hydride-Based Hydrogen Storage and Transportation Toward Large-Scale Applications of Green Hydrogen

(Invited) SOEC Upscale; Material Challenges