Abstract:Lithium-sulfur (Li-S) batteries are widely regarded as the next-generation energy storage technology, due to their high potential in energy density and a low projected cost. Practical applications of such batteries are plagued with radical challenges that mainly stem from two factors. First, both sulfur and its final lithiation product, Li2S, are insulating. Thus, the reaction kinetics is slow and often leads to a low attainable capacity. Second, active material dissolve in the electrolyte in the form of lithium polysulfides. This dissolution causes a series of problems, including loss of cathode materials by diffusion away from the cathode, collapse of the cathode structure, and the polysulfide shuttle effect. As a result, Li-S batteries commonly show fast capacity decay and low coulombic efficiency. Herein, we report the exceptional battery performance of porous carbon-sulfur composite microspheres, PSC-S, that benefited from simultaneous control of nanostructure and microscale particle morphology. The porous carbon microspheres (PSC) was synthesized as the sulfur host,by combining emulsion polymerization and evaporation-induced self-assembly (EISA) process, with a good control of both pore structure and microscale particle morphology. Such material not only demonstrated superioty in attainable capacity, but also in several other critical parameters for the development of high-energy Li-S batteries. PSC-S composite boasts a high tap density of 1.08 g/ml and contains 75 wt.% sulfur embedded into the mesopores of its carbon framework. At a high sulfur loading of 5 mg-S/cm2 and 60wt.% sulfur content in the electrode, this material delivers both high gravimetric and high volumetric capacity with excellent retention. Carbon nanotubes (CNTs) can also be readily incorporated into the microspherical structure in the synthesis process to form a porous spherical carbon-carbon nanotube-sulfur composite (PSC-CNT-S). CNT incorporation effectively raises the conductivity of the composite, and thus significantly improves its high-rate performance. At a high current density of 2.8 mA/cm2, an initial capacity of 1100 mAh/g and a reversible capacity of 700 mAh/g after 200 cycles were achieved in PSC-CNT-S. The resultant areal capacity of over 3.5 mAh/cm2 is much higher than in previous reports of Li-S cathodes fabricated using coating techniques.

Mesoporous Carbon Prepared by Etching Halloysite Nanotubes (hnts) with Pyrrole As a Precursor for a Sulfur Carrier of Superior Lithium–sulfur Batteries

Palladium nanocrystals-imbedded mesoporous hollow carbon spheres with enhanced electrochemical kinetics for high performance lithium sulfur batteries

A Novel Mangosteen Peels Derived Hierarchical Porous Carbon for Lithium Sulfur Battery

Facile and Scalable Synthesis of Micro-Mesoporous Carbon/magnesium Oxide/sulfur Composite for Lithium-Sulfur Batteries

Hierarchically Structured Sulfur/Carbon Nanocomposite Material for High-Energy Lithium Battery

Mangosteen Peel-Derived Porous Carbon: Synthesis and Its Application in the Sulfur Cathode for Lithium Sulfur Battery

A One-Step Hard-Templating Method for the Preparation of a Hierarchical Microporous-Mesoporous Carbon for Lithium-Sulfur Batteries

Preparation of mesoporous carbon and its effect on properties of lithium-sulfur batteries

Preparation and Electrochemical Performance of Sulfur/ Mesoporous Carbon Composites As Cathodes for Lithium-Sulfur Batteries

Highly Ordered Nitrogen-Rich Mesoporous Carbon Derived from Biomass Waste for High-Performance Lithium–sulfur Batteries

Preparation of Mesoporous Carbon with Different Pore Wall Structure Via a Temperature-Programmed Route for Lithium Sulfur Battery

High-content of Sulfur Uniformly Embedded in Mesoporous Carbon: a New Electrodeposition Synthesis and an Outstanding Lithium–sulfur Battery Cathode

A Mixed Microporous/Low-range Mesoporous Composite with High Sulfur Loading from Hierarchically-structured Carbon for Lithium Sulfur Batteries

Hierarchical Carbon Nanotubes with a Thick Microporous Wall and Inner Channel as Efficient Scaffolds for Lithium–Sulfur Batteries

Synthesis and Electrochemical Performance of Micro-Mesoporous Carbon-Sulfur Composite Cathode for Li–S Batteries

Composites of carbon nanotube and protonated montmorillonite as structural and chemical dual-encapsulation sulfur carrier for lithium-sulfur battery

A hierarchical micro/mesoporous carbon fiber/sulfur composite for high-performance lithium-sulfur batteries

Preparation of Mesohollow and Microporous Carbon Nanofiber and Its Application in Cathode Material for Lithium–sulfur Batteries

Nanosized CeO2C2 with Rich Oxygen Vacancies Embedded in Hollow Mesoporous Carbon As a Multifunctional Sulfur-Loaded Matrix for Lithium-Sulfur Batteries

Mesoporous Carbon-Sulfur Composite Microspheres with Multiscale Morphology Control to Achieve High Areal Capacity for Lithium-Sulfur Battery Cathodes

Nanoarchitectured Graphene/CNT@Porous Carbon with Extraordinary Electrical Conductivity and Interconnected Micro/Mesopores for Lithium‐Sulfur Batteries