Abstract:The severe oxidation of metal elements leads to a large amount of oxide inclusions that hinder the formation of metallurgical bonds across intersplat interfaces during thermal spraying in an ambient atmosphere, which further degrades the performance of thermally sprayed metal coatings. Controlling the oxidation of metal elements during spray deposition remains a significant challenge. In this paper, the thermodynamic and kinetic requirements of in-situ in-flight deoxidation by adding deoxidizer elements (diamond particles) to Fe / Al spray powders to achieve oxide-free molten droplets in an ambient atmosphere were investigated. Fe / Al / 2.5C composite powders containing 2.5wt.% diamond particles were prepared by mechanical alloying. Atmospheric plasma spraying (APS) was used to generate an oxide-free molten spray of FeAl particles at temperatures higher than 2 000 degrees C. This was achieved by the in-situ self-oxide cleaning effect of in-flight particles by carbon, which prevented metal droplets from oxidizing in an open atmosphere. For comparison, a FeAl coating was also deposited using Fe / Al composite powders prepared by mechanical alloying. The particle velocity and temperature were measured by a commercial thermal-spraying particle diagnostic system. The microstructures of the coatings were characterized by scanning electron microscopy and X-ray diffraction. The chemical compositions of the coatings were measured by inductively coupled plasma spectroscopy. The adhesive strength and hardness of the plasma-sprayed FeAl-based coatings were tested. The results show that under the combined effects of plasma- jet heating and the FeAl exothermic reaction, the heated FeAl spray particles could reach a high temperature of over 2 100 degrees C, which meets the thermodynamic conditions for carbon in-situ deoxidation. Because oxidation occurs from the surface of an in-flight molten droplet, to maintain continuous deoxidation of the molten FeAl droplet, the rapid transfer of carbon from the interior of the molten droplet to the surface is necessary. It was confirmed that the strong convection flow of the molten metal droplets satisfied the kinetic conditions of carbon in-situ in-flight deoxidation. The oxygen content in the APS-sprayed FeAl coatings increased with the increase of the spray distance. In contrast, the oxygen content in the APS-sprayed FeAl / 2.5C coatings decreased from 1.01 wt.% to 0.48 wt.% as the spray distance increased from 70 mm to 150 mm. This was accompanied by the decrease in carbon content from 1.41 wt.% to 0.31 wt.%, indicating the effective protection of Fe and Al from oxidation by the carbon in the droplet. Compared with the oxygen content of 3.67 wt.% in traditional FeAl coating, the oxygen content of the FeAl / 2.5C coatings was reduced to less than 0.5 wt.%. Considering that the carbon content of the coatings decreased as the spray distance increased, the results confirm that the in-flight oxidation of Fe and Al was suppressed by the preferential sacrificial oxidation of carbon in the molten droplets. Thus, the oxide in the FeAl / 2.5C coatings was mainly attributed to post-deposition oxidation. Moreover, the FeAl droplet reached the temperature to realize the spread-fusing self-metallurgical bonding effect for FeAl splats. The coatings exhibited a dense microstructure with an apparent porosity of less than 0.5%. The adhesive bonding strength of the prepared coatings exceeded 59.2 MPa owing to metallurgical bonding. The hardness of the coatings reached 590 HV0. 3, which was approximately twice that of traditional FeAl coatings. This was attributed to the reinforcement provided by the Fe3AlCx cementite phase resulting from the residual carbon in the coating.

Effects of Al2O3 on the Microstructures and Corrosion Behavior of Low-Pressure Cold Gas Sprayed Al 2024-Al2o3 Composite Coatings on AA 2024-T3 Substrate

Effect of Al2O3 on Microstructure and Corrosion Characteristics of Al/Al2O3 Composite Coatings Prepared by Cold Spraying

Microstructure and Properties of Cold-Sprayed Al- X %al 2 O 3 Composite Coatings on LA43M Mg-Li Alloy

Mechanical and Corrosion Properties in 3.5% NaCl Solution of Cold Sprayed Al-based Coatings

Microstructure and Tribocorrosion Behavior of Al2O3/Al Composite Coatings: Role of Al2O3 Addition

Effect Of Thickness On The Structure And Corrosion Performance Of Sputtered Ce-Al-O Coatings On Al 2024-T3 Alloy Substrates

Study on tribocorrosion properties of cold spray additively manufactured 2024 Al alloy

Mechanism of Suppressing Oxidation of FeAl Molten Droplet by Adding C to Powder and Its Effect on Microstructure and Properties of Plasma-sprayed Coating

Effect of Alkaline Etching on Formation Behavior and Corrosion Resistance of a Cr-Zr-Ti TCP Conversion Coating on AA2024 Aluminum Alloy

Corrosion behavior of cold sprayed 7075Al composite coating reinforced with TiB2 nanoparticles

Fabrication, Microstructure and Corrosion Resistance of Zn/Al Composite Coating by Arc Spraying

Influence of Al2O3 content on microstructure, electrical conductivity and adhesion strength of cold sprayed Al-Al2O3 coatings on PEEK substrate

Effects and mechanism of Zn on the structure and corrosion resistance of microarc oxidation coatings on aluminum alloy

Preparation and characterization of supersonic plasma sprayed Al–Al2O3–Cr2O3 composite coatings on magnesium alloy substrate

Microstructure and Properties of Al-Based Ceramic Coating Deposited on Magnesium Alloy Surface by Cold Spraying

Corrosion inhibition characteristics of multilayer Si-DLC, phosphating and anodizing coatings deposited on 2024 Al alloy: A comparative study

The Effect of Process Temperature and Powder Composition on Microstructure and Mechanical Characteristics of Low-Pressure Cold Spraying Aluminum-Based Coatings

Microstructural evolution and corrosion behavior of constituent particles of 2024-T3 Al alloy during zirconium conversion coating

Corrosion Behavior and Thermal Conductivity of Plasma Sprayed AlN / Al 2 O 3 Coating

Dry Sliding Wear Behaviour of Al<sub>2</sub>O<sub>3</sub>-Cr<sub>2</sub>O<sub>3</sub> Coatings with Different Contents of Cr<sub>2</sub>O<sub>3</sub>

Influence of Al contents on the long-term corrosion behaviors of cold-sprayed Zn-xAl coatings