Abstract:Following the excavation of the rectangular tunnel faces with deep harder rock, spalling often occurs on both sidewalls of the tunnel, which affects the tunnel support and stability. To investigate the spalling phenomenon of the harder rock under the deep initial three-dimensional (3D) stress conditions, true triaxial loading tests of different depths (250, 500, 750, and 1000 m) and different stress combinations (four different horizontal stresses at the same depth 1000 m) were designed on plastic fine grain marble. The overall failure process of the surrounding rock was monitored and recorded by a wireless micro-camera. The results show that, under the shallow stress condition (250 and 500 m), the V-shaped bands will appear on the both sidewall due to the overall shear failure of the specimen. Under the deep stress condition (750 and 1000 m), the obvious spalling was observed on the hole sidewalls of all marble specimens. Moreover, at the time of hole sidewall spalling, the vertical stress is the maximum principal stress. The spalling process of the hole sidewall can be divided into four stages: the microcrack initiation, the appearance of thin rock slabs, the formation of arc-shaped notches, and the expansion to V-shaped notches. If the excavation depth remains the same (1000 m) when the maximum principal stress is perpendicular to the tunnel axis, excavation along the minimum principal stress direction is beneficial to reducing the spalling damage degree. Compared to the brittle granite specimens with rectangular holes under the same 3D stress conditions, the influence of brittleness and plasticity of rock materials on spalling failure was analysed. (1) Spalling failure mode of hole sidewalls: the plastic-marble is static failure without fine particle ejection, while the brittle granite will break dynamically with fine particle ejection. (2) Spalling failure process and zones of sidewall: the cracks on the plastic marble sidewalls develop parallel to the axial direction, and run through the whole hole sidewall along the axis, while the cracks on the brittle granite hole sidewalls propagate perpendicular to the axial direction, and the sidewalls first break locally and then break through the whole hole. Failure zones on both sidewalls of the two kinds of rock specimens will transit from arc-shaped notch to V-shape notch. Those failure notches are symmetrical and finally penetrate the sidewalls. (3) Microscopic failure mode: scanning electron microscope (SEM) shows that the plastic and brittle rock materials are tensile failure during the spalling under 3D stress conditions. The plastic marble is characterized by fracture tension failure, while the brittle granite is characterized by layered tension failure. Some suggestions are given finally, under the condition that the vertical stress is the maximum principal stress, when the tunnel is excavated along the horizontal direction, the resistant ability of the tunnel sidewall in the plastic and brittle surrounding rock should be strengthened by supporting the sidewall, which can effectively reduce the degree of spalling damage.

Experimental Simulation Analysis of the Process and Failure Characteristics of Spalling in D-shaped Tunnels under True-Triaxial Loading Conditions

Experimental Investigation of Spalling Failure of D-Shaped Tunnel Under Three-Dimensional High-Stress Conditions in Hard Rock

Experimental simulation and investigation of spalling failure of rectangular tunnel under different three-dimensional stress states

Experimental and theoretical analysis of spalling in deep hard rock tunnels with different arch structures

Experimental simulation investigation of influence of depth on spalling characteristics in circular hard rock tunnel

Experimental simulation study of spalling in deep rectangular tunnel with plastic fine grain marble

Laboratory Observation of Spalling Process Induced by Tangential Stress Concentration in Hard Rock Tunnel

Stress Analysis and Spalling Failure Simulation on Surrounding Rock of Deep Arch Tunnel

Real-time monitoring of the development of brittle fracture in hard rock tunnels based on physical model test

Numerical study on spalling failure of rock surrounding deep buried tunnel based on DEM

Experimental Study on Rockburst and Spalling Failure in Circular Openings for Deep Underground Engineering

Fracturing process and initiation mechanism of hard rock tunnels with different shapes: particle flow modeling and analytical study

Evolution law and mechanism of time-delayed spalling in a deep TBM tunnel: A case study

Failure process and characteristics of deep concrete-supported arch tunnel under true-triaxial stress

Evaluation of in-situ stress based on spalling behavior of hard rock mass

Experimental investigation on stress-induced failure in D-shaped hard rock tunnel under water-bearing and true triaxial compression conditions

Excavation Stress Path Induced Fracturing Mechanism of Hard Rock in Deep Tunnel

Shear failure process of rectangular tunnel: Physical experimental test and numerical back-analysis

Experimental Investigation on Failure Mechanism and Rockburst Process of Tunnels Under Different Span-Ratios and Existing Structural Planes

Stress Distribution and Stress-induced Failures in Surrounding Rock Mass of Deep Tunnels

Spalling failure and fracturing of brittle sandstone containing rectangular cavity based on biaxial compression test and discrete element method