Abstract:In this paper, the influence mechanism of ultrasound on plastic flow and microstructure features of the aluminum–copper friction stir lap welding (Al/Cu-FSLW) process is systematically investigated by adjusting the welding speed and improving the shear rheology in the plastic stirring zone. Through adjusting the ultrasonic vibration and welding speed, the directional control of mechanical properties is realized. It is found that increasing the welding speed properly is beneficial to enhance the mechanical shear between the tool and the workpiece, thus forming more staggered layered structures at the copper side and improving the tensile strength of the weld. The acoustic softening enhances the viscoplastic fluid mixing and strengthens the mechanical interlock of the Al/Cu lap interface. As the welding speeds increase or ultrasonic vibration is applied, the thickness of Al/Cu intermetallic compound (IMC) decreases, and the tensile strength and elongation of the Al/Cu joints are enhanced. Compared with adjusting the welding speed, the ultrasonic vibration can further refine the copper particles which are stirred into the plastic zone, and the thinning effect of ultrasound on IMC layers is better than that of increasing welding speed. At the welding speed of 60 mm/min, the IMC layer thickness is reduced by 42% under ultrasonic effect. In three welding speed conditions, the UV reduced the absolute value of the effective heat of formation (EHF) for Al2Cu and Al4Cu9 and suppressed the formation of AlCu phase. Meanwhile, only when the welding speed is increased from 60 mm/min to 100 mm/min can the formation of AlCu be suppressed. Under the ultrasonic optimization, the stable improvement of welding efficiency is ensured.

Analysis of Droplet Transfer, Weld Formation and Microstructure in Al-Cu Alloy Bead Welding Joint with Pulsed Ultrasonic-Gmaw Method

Effect of ultrasonic vibration on porosity suppression and columnar-to-equiaxed transition in laser-MIG hybrid welding of aluminum alloy

Comparative Study of Droplet Transfer Modes on Appearance, Microstructure, and Mechanical Properties of Weld During Pulsed GMAW

Effect of Ultrasonic Power on Microstructural and Mechanical Properties of Al/Cu Plasma Arc Welding–Brazing Joints

Dynamic Weld evolution during ultrasonic welding of Cu–Al joints

The Influence of Coaxial Ultrasound on the Droplet Transfer of High Nitrogen Steel GMAW Process

Effect of Ultrasonic Vibration on Grain Size and Precipitated Phase Distribution of 6061 Aluminum Alloy Welded Joint

Study on Short-Circuiting GMAW Pool Behavior and Microstructure of the Weld with Different Waveform Control Methods

Study on the thermo-effect of P-GMAW characterized by structure-borne acoustic emission signals detected in welding on aluminum alloy

Investigation on the Dynamic Behavior of Weld Pool and Weld Microstructure During DP-GMAW for Austenitic Stainless Steel

Study on the Effect of Pulse Waveform Parameters on Droplet Transition, Dynamic Behavior of Weld Pool, and Weld Microstructure in P-GMAW

Effects of Arc-Excited Ultrasonic on Microstructures and Properties of Weld

Study on the effects of ultrasonic assistance and external heat dissipation on friction stir welded 7075 aluminum alloy joints

Microstructure and Mechanical Properties of Ultrasonic Welded Joint of 1060 Aluminum Alloy and T2 Pure Copper

Influence of Metal Transfer Modes on Pore Formation during the Welding Process of AA6082/A360 Dissimilar Aluminum Alloys

Molecular Dynamics Simulations of Atomic Diffusion during the Al–Cu Ultrasonic Welding Process

Effect of high-frequency phase shift on metal transfer and weld formation in aluminum alloy double-wire DP-GMAW

Effect of Ultrasound on Microstructure and Properties of Aluminum–Copper Friction Stir Lap Welding

Droplet detachment and motion behaviors in laser-MIG hybrid welding of aluminum alloy

Effect of an Ultrasonic Vibration on the Microstructure and Properties of Al Alloy/Steel Laser Welding-Brazing Joints

Heat input characteristics and weld bead formation in double-wire double-pulsed GMAW of aluminum alloy under different low-frequency phases