Natural Chalcopyrite As a Sulfur Source and Its Electrochemical Performance for Lithium–sulfur Batteries

Jiahui Zhou,Sijie Li,Wei Sun,Xiaobo Ji,Yue Yang

DOI: https://doi.org/10.1039/c9qi00054b

IF: 7.779

2019-01-01

Inorganic Chemistry Frontiers

Abstract:Natural chalcopyrite with high capacity and good cycling performance is used as a sulfur source for lithium–sulfur batteries.

What problem does this paper attempt to address?

Chloride‐Reinforced Carbon Nanofiber Host As Effective Polysulfide Traps in Lithium–Sulfur Batteries

Lei Fan,Houlong L. Zhuang,Kaihang Zhang,Valentino R. Cooper,Qi Li,Yingying Lu

DOI: https://doi.org/10.1002/advs.201600175

IF: 15.1

2016-01-01

Advanced Science

Abstract:Lithium–sulfur (Li–S) battery is one of the most promising alternatives for the current state‐of‐the‐art lithium‐ion batteries due to its high theoretical energy density and low production cost from the use of sulfur. However, the commercialization of Li–S batteries has been so far limited to the cyclability and the retention of active sulfur materials. Using co‐electrospinning and physical vapor deposition procedures, we created a class of chloride–carbon nanofiber composites, and studied their effectiveness on polysulfides sequestration. By trapping sulfur reduction products in the modified cathode through both chemical and physical confinements, these chloride‐coated cathodes are shown to remarkably suppress the polysulfide dissolution and shuttling between lithium and sulfur electrodes. From adsorption experiments and theoretical calculations, it is shown that not only the sulfide‐adsorption effect but also the diffusivity in the vicinity of these chlorides materials plays an important role on the reversibility of sulfur‐based cathode upon repeated cycles. Balancing the adsorption and diffusion effects of these nonconductive materials could lead to the enhanced cycling performance of an Li–S cell. Electrochemical analyses over hundreds of cycles indicate that cells containing indium chloride‐modified carbon nanofiber outperform cells with other halogenated salts, delivering an average specific capacity of above 1200 mAh g−1 at 0.2 C.
Natural Okra Shells Derived Nitrogen‐Doped Porous Carbon to Regulate Polysulfides for High‐Performance Lithium–Sulfur Batteries

Yanjuan Li,Lihuai Liu,Rongjia Shi,Shun Yang,Chengxiao Zhao,Yanhui Shi,Changsheng Cao,Xiao Yan

DOI: https://doi.org/10.1002/ente.201900165

IF: 4.149

2019-01-01

Energy Technology

Abstract:Low conductivity of elemental sulfur, the “shuttle effect” of polysulfides, and structural change hamper lithium–sulfur batteries that have poor electrochemical performance. Herein, a facile and scalable approach to fabricate porous carbon is derived from common okra wastes, okra shells, as a matrix for sulfur active materials. Especially, the material calcined under NH3 (N‐doped biomass‐derived porous carbon [N‐OSC]) with a high specific surface area of 2702 m2 g−1 and large pore volume (0.17 cm3 g−1) provides necessary physical adsorption, resulting in the 69.71 wt% loading of sulfur and excellent trapping capacity for polysulfides during the redox process. Furthermore, N element can act as catalytic active sites to facilitate redox conversion from polysulfides to Li2S. Benefiting from the aforementioned advantages, the cell of the N‐OSC/S electrode manifests superior electrochemical performance. The initial capacity is found up to be 1387 mA h g−1 at a current density of 0.1 C and 750 mA h g−1 after 200 cycles at 0.5 C rate (where 1 C = 1672 mA h g−1). For durability evaluations, the capacity is maintained at 416 mA h g−1 at 2 C after 1000 cycles with a mere decay of 0.05% per cycle.
Unraveling the Mechanism of Chalcopyrite’s Superior Performance for Lithium Storage

Feng Jiang,Wenqing Zhao,Limin Zhang,Ye Tian,Xu Gao,Peng Ge,Wei Sun,Xinghua Chang,Xiaobo Ji

DOI: https://doi.org/10.1021/acsaem.1c00641

IF: 6.4

2021-05-07

ACS Applied Energy Materials

Abstract:Chalcopyrite (CuFeS2), a natural copper–iron bimetallic sulfide, has shown great promise as an active material for lithium-ion batteries because of its superior electrochemical performance, high abundance, and low cost. However, its reaction mechanisms are still indeterminate. Herein, we demonstrate that chalcopyrite CuFeS2 exhibits unique phase and structure transformations during electrochemical reactions, which are highly related to its superior electrochemical performance. In situ XRD and ex situ XPS characterizations reveal that CuFeS2 is converted into a nanoscale hybrid that contains Cu2S and FeSy after the initial discharge–charge cycle. The emerging heterostructure endows the electrode with structural integrity, suppressed polysulfide dissolution, and enhanced charge transfer and Li-ion diffusion during reactions. In consequence, CuFeS2 exhibits excellent lithium-storage performance with a high specific capacity of 990 mAh g–1 after 300 cycles under the current density of 1000 mA g–1. This work sheds light on the intrinsic electrochemical superiority of chalcopyrite CuFeS2 and provides guidelines to understand other bimetallic sulfides.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00641?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00641</a>.Preparation flowcharts; ex situ XPS spectra; HRTEM image; CV curves; linear relationships of log(Ip) vs log(v), Ip vs v1/2, I/v1/2 vs v1/2, and Zr vs υ–1/2; Nyquist plots; TEM images; chemical composition; Rct value (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00641/suppl_file/ae1c00641_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,chemistry, physical,energy & fuels
A High-Energy Sulfur Cathode in Carbonate Electrolyte by Eliminating Polysulfides Via Solid-Phase Lithium-Sulfur Transformation

Xia Li,Mohammad Banis,Andrew Lushington,Xiaofei Yang,Qian Sun,Yang Zhao,Changqi Liu,Qizheng Li,Biqiong Wang,Wei Xiao,Changhong Wang,Minsi Li,Jianwen Liang,Ruying Li,Yongfeng Hu,Lyudmila Goncharova,Huamin Zhang,Tsun-Kong Sham,Xueliang Sun

DOI: https://doi.org/10.1038/s41467-018-06877-9

IF: 16.6

2018-01-01

Nature Communications

Abstract:Carbonate-based electrolytes demonstrate safe and stable electrochemical performance in lithium-sulfur batteries. However, only a few types of sulfur cathodes with low loadings can be employed and the underlying electrochemical mechanism of lithium-sulfur batteries with carbonate-based electrolytes is not well understood. Here, we employ in operando X-ray absorption near edge spectroscopy to shed light on a solid-phase lithium-sulfur reaction mechanism in carbonate electrolyte systems in which sulfur directly transfers to Li 2 S without the formation of linear polysulfides. Based on this, we demonstrate the cyclability of conventional cyclo-S 8 based sulfur cathodes in carbonate-based electrolyte across a wide temperature range, from −20 °C to 55 °C. Remarkably, the developed sulfur cathode architecture has high sulfur content (>65 wt%) with an areal loading of 4.0 mg cm −2 . This research demonstrates promising performance of lithium-sulfur pouch cells in a carbonate-based electrolyte, indicating potential application in the future.
Nanostructured Β-Li3ps4 for All-Solid Lithium-Sulfur Batteries

Chengdu Liang,Zhan Lin,Zengcai Liu,Nancy J. Dudney,Adam J. Rondinone,E. Andrew Payzant

DOI: https://doi.org/10.1149/ma2012-02/5/330

2012-01-01

ECS Meeting Abstracts

Abstract:Using elemental sulfur and elemental lithium as cathode and anode, respectively, the lithiumsulfur (Li-S) battery represents the simplest battery chemistry for rechargeable batteries. In spite of the high theoretical energy density of 2600 Wh/kg, Li-S batteries suffer from poor cyclability. There are three key limitations for cycling Li-S batteries that must be overcome: (1) Sulfur is an electronic insulator. Its poor electronic conductivity leads to low utilization of active material in the electrode. This problem can be overcome by using high surface area carbon in the cathode. (2) The charge and discharge products of sulfur are poor ionic conductors. In order to make the sulfur cathode rechargeable, a liquid electrolyte that has a high solubility of polysulfides is required to overcome the poor ionic conductivities of solid sulfur species. As a result of the dissolution polysulfides in the liquid electrolyte, the diffusion of polysulfides from the cathode to the anode during the battery cycling leads to the corrosion of lithium anode and the loss of active sulfur materials. (3)The dendritic growth of lithium metal in liquid electrolytes and the ever growing of solid electrolyte interphase on the anode surface shorten the cycle-life of Li-S batteries and also cause safety concerns. Therefore, the poor cyclability of Li-S batteries is an intrinsic problem associated with the use of liquid electrolyte in the battery configuration.
Natural Vermiculite Enables High‐Performance in Lithium–Sulfur Batteries via Electrical Double Layer Effects

Feixiang Wu,Haifeng Lv,Shuangqiang Chen,Simon Lorger,Vesna Srot,Martin Oschatz,Peter A. van Aken,Xiaojun Wu,Joachim Maier,Yan Yu

DOI: https://doi.org/10.1002/adfm.201902820

IF: 19

2019-05-09

Advanced Functional Materials

Abstract:Lithium–sulfur batteries with potentially high specific energy are viewed as very promising candidates for next‐generation lightweight and low‐cost rechargeable batteries. However, sulfur‐based cathodes suffer from dissolution of polysulfides causing shuttle effects. Here, in order to confine elemental sulfur and anchor the polysulfides, a novel host that is an inexpensive natural clay mineral, viz., vermiculite is proposed. When compared to regular carbon–sulfur composites, vermiculite–sulfur composites offer promising rate capability and much better cycling stabilities, displaying capacity retentions of ≈89 and ≈93% within 200 cycles at C/2 and 1 C, respectively, and ≈60 % at C/5 within 1000 cycles. Postmortem studies, advanced adsorption tests, density functional theory calculations, and zeta potential measurements in combination with intrinsic characteristics of the natural vermiculite provide insights into the new mechanism. The vermiculite contains naturally present surface cations which show a strong tendency to adsorb Sn2− anions, hence protecting them from dissolution. The excess surface charge is most probably compensated by excess Li+ in the space charge zones which is beneficial for charge transfer and local conductivity. The reported results show that natural clay‐minerals are promising sulfur hosts being able to fixate sulfides via electrical double layer effects, thus enabling high‐performance in lithium–chalcogen batteries.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Feasible Catalytic-Insoluble Strategy Enabled by Sulfurized Polyacrylonitrile with In Situ Built Electrocatalysts for Ultrastable Lithium–Sulfur Batteries

Xiaomin Yuan,Bo Zhu,Jinkui Feng,Chengguo Wang,Xun Cai,Rongman Qin

DOI: https://doi.org/10.1021/acsami.1c14388

2021-10-20

Abstract:To date, elemental sulfur has been considered as a prospective cathode material for exploring high-energy power systems with low cost and sustainability. However, its practical commercialization has been impeded by inherent drawbacks of notorious capacity decay, unsatisfied insulating nature, and sluggish conversion chemistry. To address these issues, for the first time, freestanding nanofibrous networks with hierarchical nanostructures are facilely constructed by inlaying electrocatalytic bimetallic chalcogenides (FexMn1-xS nanoparticles) into conductive graphene nanosheet (GN)-doped sulfurized polyacrylonitrile (SPAN) fiber matrices. Covalent-bonded SPAN featuring an insoluble mechanism serves as a reliable cathode substrate with enhanced electrostability and high sulfur utilization, while high-surface-area GN dopants promote conductivity improvement and rapid electron transfer. Meanwhile, the results prove that sulfiphilic FexMn1-xS nanoparticles with abundant electrochemically active sites facilitate construction of uniform deposition interfaces and efficient electrocatalysis conversion toward lithium polysufides. This feasible catalytic-insoluble cathode strategy drives the Li-S battery, which exhibits excellent electrochemical performances with a remarkable reversible discharge capacity of 967 mA h g-1 and a capacity retention of 623 mA h g-1 after 500 cycles. Moreover, the corresponding lithiation/delithiation mechanisms are systematically investigated through complementary morphological and spectral analyses, providing valuable insights into advanced metal-sulfur batteries.

materials science, multidisciplinary,nanoscience & nanotechnology
Engineering Peculiar Cathode Electrolyte Interphase toward Sustainable and High‐Rate Li–S Batteries

Chang‐Ding Qiu,Youcheng Hu,Kewei Cao,Xiangjiang Wu,Bi‐Hong Huang,Jin Liu,Yun‐Xiao Wang,Laibing Luo,Dong Gu,Xinping Ai,Yuliang Cao,Shengli Chen,Fu‐Sheng Ke

DOI: https://doi.org/10.1002/aenm.202300229

IF: 27.8

2023-04-11

Advanced Energy Materials

Abstract:A favorable cathode electrolyte interphase (CEI) design is realized for sulfur electrodes by the fast reaction between vinylene carbonate, bis(trifluoromethane)sulfonimide ions, and lithium polysulfides during the initial discharge process. This strategy leads to the in situ formation of a robust, thin, and self‐healing CEI without sacrificing interfacial Li+ transport. Thus, the CEI‐confined sulfur cathodes perform well under high‐rate, long‐cycle stability, low N/P ratio, and subzero temperature. The lithium–sulfur battery is considered to be one of the most promising rechargeable energy storage systems because of its high theoretical energy density. Unfortunately, the shuttle effect during cycling causes serious loss of sulfur species and corrosion of the lithium metal anode, resulting in severe capacity decay. This work proposes to completely suppress the shuttle effect of lithium polysulfides (LiPSs) without sacrificing the interfacial Li+ transport, through in situ construction of a compact cathode electrolyte interphase (CEI), which is formed of the reaction between vinylene carbonate (VC), bis(trifluoromethane)sulfonimide ions and LiPSs in a self‐limiting manner during the initial discharge process. Hence, the CEI‐confined sulfur cathode in the VC‐based electrolyte with a solid phase conversion mechanism delivers a long‐term cycling stability and high‐rate performance, as well as excellent performance under an extreme climate in a subzero temperature of −20 °C, limited lithium source with a low N/P ratio of 1.1, and even at mechanical mutilation. The present study reveals an appealing approach to tailor the composition and interfacial structure of sulfur cathodes by in situ construction of a robust, self‐healing, and high Li+ conductive CEI from the aspect of electrolyte, and thus completely solve the issue of the shuttle effect.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Stable lithium-sulfur batteries with high sulfur content fabricated by ultralight ochroma lagopus-derived carbon with dopamine shell as sulfur host

Yinze Zuo,Peijia Ren,Meng Zhao,Weiming Su,Yanbin Chen,Yuefeng Tang,Yanfeng Chen

DOI: https://doi.org/10.1016/j.jallcom.2019.152995

IF: 6.2

2020-01-01

Journal of Alloys and Compounds

Abstract:Breaking through low sulfur loading and shuttle effect are the key to achieve high performance lithium-sulfur battery. It is necessary to prepare an ultralight sulfur host with strong polysulfide adsorption/blocking ability. Herein, the polydopamine coated ochroma lagopus carbon (A-PDA@OLC) with super-high specific surface area is exploited as sulfur host for high-performance lithium-sulfur batteries. The cathode with 60.13 wt % sulfur content (2 mg cm(-2) sulfur loading) delivered the higher initial capacity of 1294.27 mA h g(-1) and excellent reversible capacity (959.13 mA h g(-1) at 0.1C after 200 cycles). Moreover, when the sulfur content was increased to 82.30 wt% (4 mg cm(-2) sulfur loading), the A-PDA@OLC@S cathode exhibits the higher reversible capacity of 1258 mA h g(-1) at 0.1C and a prolonged cycle life (723 mA h g(-1) after 250 cycles). The prepared PDA coated natural ultralight biochar are proven to be an effective strategy for the encapsulation and adsorption of lithium polysulfides(LiPSs), which demonstrates enhanced electrochemical performance for high-sulfur-loading Li-S batteries. (C) 2019 Published by Elsevier B.V.
Enhanced Electrochemical Kinetics with Highly Dispersed Conductive and Electrocatalytic Mediators for Lithium–Sulfur Batteries

Ji Qian,Yi Xing,Yong Yang,Yu Li,Kaixin Yu,Wanlong Li,Teng Zhao,Yusheng Ye,Li Li,Feng Wu,Renjie Chen

DOI: https://doi.org/10.1002/adma.202100810

IF: 29.4

2021-05-13

Advanced Materials

Abstract:Lithium–sulfur (Li–S) batteries are promising energy‐storage devices because of their high theoretical energy densities. However, the practical application of Li–S batteries is still impeded by the poor cycling performance and rate capability at practical conditions. In order to improve the performance of practical Li–S batteries, a hierarchical Mo2C nanocluster/carbon nanosheets hybrid based hollow spherical material (Mo2C/CHS) is designed and prepared. The hollow spheres composed of stacked carbon nanosheets can facilitate the infiltration of electrolyte. The ultrasmall and highly conductive Mo2C nanocrystals are confined in the carbon nanosheets and expose more active sites for anchoring and conversion of lithium polysulfides and increase the number of the nuclei for Li2S2/Li2S precipitation. Benefitting from the synergistic effects, Mo2C/CHS greatly promotes electrochemical kinetics in Li–S batteries with high sulfur loading (5 mg cm−2). Even under lean electrolyte conditions (E/S = 7 μL mgsulfur−1), the Li–S batteries with Mo2C/CHS added exhibit a discharge capacity of 904 mAh g−1 at the high current rate of 0.5 C, and with 894 mAh g−1 maintained after 200 cycles. This work provides a fundamental understanding of the electrochemical processes and guides the rational design of host and additive materials for practical Li–S batteries.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
High Sulfur Loading of Cathodes for Li-S Batteries

Wen Liu,Yong Li,Gui Guo,Hai Juan Pei,Wen Zheng Fu,Jingying Xie

DOI: https://doi.org/10.1149/ma2014-04/3/577

2014-01-01

ECS Meeting Abstracts

Abstract:Lithium sulfur batteries have attracted the most attention owing to their high energy density (2600Wh/kg), while the specific capacity and capacity retention of sulfur electrodes play a crucial role on increasing the energy density of lithium sulfur batteries. Many researches focus on the materials with very high specific capacity per gram of sulfur but very low sulfur content and cells with very low sulfur loading of cathodes [1-3]. In this work, the cells with much higher sulfur loading of electrodes (4.34mg S/cm2, named as S-L and 7.24mg S/cm2, named as S-H) show better electrochemical performance. Fig. 1(a) shows the first discharge/charge potential curves of lithium sulfur batteries with S-L and S-H as cathodes. Two plateaus (about 2.35V and 2.10V) in the discharge curve and one plateaus (about 2.20-2.40V) in the charge curve are observed, which agree well with the previous work [4]. Comparison of cycling performance between S-L and S-H cathode was shown in Fig. 1(b). S-L cathode shows an initial specific capacity of 845mAh/g at 50mA/g between 1.50-2.80V, which exhibits a discharge capacity of 763mAh/g after 45 cycles with a capacity retention of 90.3%. Moreover, the cell with S-H cathode delivers 836mAh/g and 754mAh/g at the first cycle and the 25th cycle, respectively. The excellent electrochemical performance of high sulfur loading of electrodes makes the development of high energy Li-S batteries possible. Fig. 1 (a) The first discharge/charge potential curves of lithium sulfur batteries with S-L and S-H as cathode between 1.50-2.80V; (b) Comparison of cycling performance between S-L and S-H cathode. Reference: [1] F. F. Zhang, X. B. Zhang, Y. H. Dong, L. M. Wang, J. Mater. Chem., 2012, 22, 11452. [2] S. Evers, L. F. Nazar, Chem. Commun., 2012, 48, 1233. [3] G. Zheng, Y. Yang, J.J. Cha, S. S. Hong, Yi Cui, Nano Lett., 2011, 11, 4462. [4] L. Xiao, Y. Cao, J. Xiao, B. Schwenzer, M. H. Engelhard, L. V. Saraf, Z. Nie, G. J. Exarhos, J. Liu, Adv. Mater., 2012, 24, 1176.
Sulfur-infiltrated porous carbon microspheres with controllable multi-modal pore size distribution for high energy lithium–sulfur batteries

Cunyu Zhao,Lianjun Liu,Huilei Zhao,Andy Krall,Zhenhai Wen,Junhong Chen,Patrick Hurley,Junwei Jiang,Ying Li

DOI: https://doi.org/10.1039/c3nr04532c

IF: 6.7

2014-01-01

Nanoscale

Abstract:Sulfur has received increasing attention as a cathode material for lithium-sulfur (Li-S) batteries due to its high theoretical specific capacity. However, the commercialization of Li-S batteries is limited by the challenges of poor electrical conductivity of sulfur, dissolution of the polysulfide intermediates into the electrolyte, and volume expansion of sulfur during cycling. Herein, we report the fabrication of novel-structured porous carbon microspheres with a controllable multi-modal pore size distribution, i.e., a combination of interconnected micropores, mesopores and macropores. Cathodes made of sulfur infiltrated in such a hierarchical carbon framework provide several advantages: (1) a continuous and high surface area carbon network for enhanced electrical conductivity and high sulfur loading; (2) macropores and large mesopores bridged by small mesopores to provide good electrolyte accessibility and fast Li ion transport and to accommodate volume expansion of sulfur; and (3) small mesopores and micropores to improve carbon/sulfur interaction and to help trap polysulfides. An initial discharge capacity at 1278 mA h g(-1) and capacity retention at 70.7% (904 mA h g(-1)) after 100 cycles at a high rate (1 C) were achieved. The material fabrication process is relatively simple and easily scalable.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry
High performance Li-ion sulfur batteries enabled by intercalation chemistry

Dongping Lv,Pengfei Yan,Yuyan Shao,Qiuyan Li,Seth Ferrara,Huilin Pan,Gordon L Graff,Bryant Polzin,Chongmin Wang,Ji-Guang Zhang,Jun Liu,Jie Xiao

DOI: https://doi.org/10.1039/c5cc05171a

2015-09-11

Abstract:The unstable interface of lithium metal in high energy density Li sulfur (Li-S) batteries raises concerns of poor cycling, low efficiency and safety issues, which may be addressed by using intercalation types of anode. Herein, a new prototype of Li-ion sulfur battery with high performance has been demonstrated by coupling a graphite anode with a sulfur cathode (2 mA h cm(-2)) after successfully addressing the interface issue of graphite in an ether based electrolyte.
Enhanced Sulfur Transformation by Multifunctional FeS2/FeS/S Composites for High‐Volumetric Capacity Cathodes in Lithium–Sulfur Batteries

Kai Xi,Deqing He,Chris Harris,Yuankun Wang,Chao Lai,Huanglong Li,Paul R. Coxon,Shujiang Ding,Chao Wang,Ramachandran Vasant Kumar

DOI: https://doi.org/10.1002/advs.201800815

IF: 15.1

2019-01-01

Advanced Science

Abstract:Lithium-sulfur batteries are currently being explored as promising advanced energy storage systems due to the high theoretical specific capacity of sulfur. However, achieving a scalable synthesis for the sulfur electrode material whilst maintaining a high volumetric energy density remains a serious challenge. Here, a continuous ball-milling route is devised for synthesizing multifunctional FeS2/FeS/S composites for use as high tap density electrodes. These composites demonstrate a maximum reversible capacity of 1044.7 mAh g(-1) and a peak volumetric capacity of 2131.1 Ah L-1 after 30 cycles. The binding direction is also considered here for the first time between dissolved lithium polysulfides (LiPSs) and host materials (FeS2 and FeS in this work) as determined by density functional theory calculations. It is concluded that if only one lithium atom of the polysulfide bonds with the sulfur atoms of FeS2 or FeS, then any chemical interaction between these species is weak or negligible. In addition, FeS2 is shown to have a strong catalytic effect on the reduction reactions of LiPSs. This work demonstrates the limitations of a strategy based on chemical interactions to improve cycling stability and offers new insights into the development of high tap density and high-performance sulfur-based electrodes.
Cobalt Phosphide Nanoflake-Induced Flower-like Sulfur for High Redox Kinetics and Fast Ion Transfer in Lithium-Sulfur Batteries

Congyu Qi,Zheng Li,Changzhi Sun,Chunhua Chen,Jun Jin,Zhaoyin Wen

DOI: https://doi.org/10.1021/acsami.0c14260

2020-10-20

Abstract:Sulfur reactivity in lithium–sulfur batteries highly depends on its distribution and morphology during cycling, which is of great significance to suppress the shuttle effect and promote conversion reaction. Herein, cobalt phosphide nanoflakes are prepared and used as a sulfur host. An improved redox kinetics from sulfur to lithium sulfide and the corresponding fast lithium-ion diffusion are observed to greatly promote the electrochemical performance of lithium–sulfur batteries. Meanwhile, for the first time, we propose "effective triple phase contact" and "insulated dead sulfur" to account for cycling performance differences of and batteries. The flower-like sulfur induced by CoP nanoflakes during cycling provides extra lithium-ion diffusion and electron transfer ways compared with agglomerated sulfur in the cathode. The battery shows good rate performance and delivers 520 mA h g–1 after 1000 cycles with an excellent Coulombic efficiency of 99%. In contrast, no conversion reaction happens after 600 cycles in the battery, implying no existence of reactive sulfur. This research reveals the effect of morphological evolution of sulfur on the cycling performance and affords an insight for developing high-performance lithium–sulfur batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14260?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14260</a>.Preparation of Co-glycerol, CoP, , and ; fabrication of Li2S6 and symmetric cell assembly; electrochemical measurements; SEM and TEM images of Co-glycerol spheres; pore size distribution of CoP; XRD patterns of ; N2 adsorption and desorption isotherms and calculated pore size distributions of ; TEM images of CoP with different hydrothermal hours; STEM–HAADF images of and the corresponding EDS maps; electrochemical performance of the cathode; EIS tests of and batteries after 100 cycles; and comparison of the capacity retention after several cycles of the Li–S battery (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14260/suppl_file/am0c14260_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,nanoscience & nanotechnology
A Chemically Stabilized Sulfur Cathode for Lean Electrolyte Lithium Sulfur Batteries

Chao Luo,Enyuan Hu,Karen J. Gaskell,Xiulin Fan,Tao Gao,Chunyu Cui,Sanjit Ghose,Xiao-Qing Yang,Chunsheng Wang

DOI: https://doi.org/10.1073/pnas.2006301117

IF: 11.1

2020-01-01

Proceedings of the National Academy of Sciences

Abstract:Significance Sulfur is a promising cathode material for rechargeable lithium batteries due to its high capacity, low cost, abundance, and high sustainability. However, lithium sulfur batteries suffer from poor cycle life and low energy density under lean electrolyte conditions because of the dissolution of lithium polysulfide intermediates. Here, we report that the chemical bonding between sulfur and carbon/oxygen in an oxygen-rich dense carbon host can stabilize sulfur and improve the stability of lean electrolyte lithium sulfur batteries. This work opens up a way to develop chemical bonding-stabilized sulfur materials for stable and high-energy lithium sulfur batteries.
Rational Designed Mixed-Conductive Sulfur Cathodes for All-Solid-State Lithium Batteries

Jie Yue,Yonglin Huang,Sufu Liu,Ji Chen,Fudong Han,Chunsheng Wang

DOI: https://doi.org/10.1021/acsami.0c08564

IF: 9.5

2020-01-01

ACS Applied Materials & Interfaces

Abstract:All-solid-state lithium-sulfur batteries (ASSLSBs) hold great promise for safe and high-energy-density energy storage. However, developing high-performance sulfur cathodes has been proven difficult due to low electronic and ionic conductivities and large volume change of sulfur during charge and discharge. Here, we reported an approach to synthesize sulfur cathodes with a mixed electronic and ionic conductivity by infiltrating a solution consisting of Li3PS4 (LPS) solid electrolyte and S active material into a mesoporous carbon (CMK-3). This approach leads to a uniform dispersion of amorphous Li3PS7 (L3PS) catholyte in an electronically conductive carbon matrix, enabling high and balanced electronic/ionic conductivities in the cathode composite. The inherent porous structure of CMK-3 also helps to accommodate the strain/stress generated during the expansion and shrinkage of the active material. In sulfide-based all-solid-state batteries with Li metal as the anode, this cathode composite delivered a high capacity of 1025 mAh g(-1) after 50 cycles at 60 degrees C at 1/8C. This work highlights the important role of high and balanced electronic and ionic conductivities in developing high-performance sulfur cathodes for ASSLSBs.
Electrode Design with Integration of High Tortuosity and Sulfur-Philicity for High-Performance Lithium-Sulfur Battery

Hao Chen,Guangmin Zhou,David Boyle,Jiayu Wan,Hongxia Wang,Dingchang Lin,David Mackanic,Zewen Zhang,Sang Cheol Kim,Hye Ryoung Lee,Hansen Wang,Wenxiao Huang,Yusheng Ye,Yi Cui

DOI: https://doi.org/10.1016/j.matt.2020.04.011

IF: 18.9

2020-01-01

Matter

Abstract:Practical applications of Li-S batteries are hindered by the dissolution/diffusion loss of sulfur-related active materials in cathode and dendrite growth in Li metal anode. Here we present an integrated sulfur cathode design on tortuosity and sulfur-binding affinity parameters for mitigating diffusion loss of sulfur-based active materials. The high sulfur-philicity property (from oxygen functional groups, 16% in concentration) in reduced graphene oxide (rGO) host favors bonding with sulfur species to mitigate their diffusion/dissolution loss, while the high tortuosity (13.24, from horizontal arrangement of rGO sheets) can localize the soluble active materials within the host rather than outward diffusion loss with subsequent uneven redeposition. With this integrated concept, we achieved ultrahigh cathode areal capacities of 21 mAh cm−2 with 98.1% retention after 160 cycles, surpassing those electrodes with lower tortuosity and sulfur-philicity. In addition, same rGO host suppresses dendrite growth in Li anode, enabling 278% prolonged cycle life in the full cell.
Natural Graphene Microsheets/sulfur As Li-S Battery Cathode Towards >99% Coulombic Efficiency of Long Cycles

Yan Zhang,Xiaoyong Duan,Jie Wang,Congwei Wang,Junying Wang,Jianlong Wang,Junzhong Wang

DOI: https://doi.org/10.1016/j.jpowsour.2017.11.061

IF: 9.2

2018-01-01

Journal of Power Sources

Abstract:Lithium-sulfur battery receives intense attention owing to its high theoretical energy density. However, poor electrical conductivity of sulfur and poor cycle stability of the battery hinder its application. Here, we report that graphene microsheets prepared from microcrystalline graphite minerals by an electrochemical & mechanical approach work as a special conductive support to load sulfur as the cathode of lithium-sulfur battery. The graphene microsheets have the features of excellent conductivity and low defect, small sheet sizes of < 1 mu m(2) and <= 6 atomic layers as well as natural silicate residue covered. Li-S batteries of graphene microsheets/S as cathode exhibit long-term cyclability and high coulombic efficiency. At 1 C for 2000 cycles, average coulombic efficiency of 99.7% is reached.
Ultrafine Iron Boride as a Highly Efficient Nanocatalyst Expedites Sulfur Redox Electrochemistry for High‐Performance Lithium‐Sulfur Batteries

Guxian Chen,Hongyang Li,Yuqi Wang,Yingrui Ding,Pengsen Qian,Kailong Zhang,Haibo Zeng,Gaoran Li

DOI: https://doi.org/10.1002/batt.202400128

2024-04-08

Batteries & Supercaps

Abstract:Lithium‐sulfur (Li‐S) batteries have garnered significant interest as a strong contender for future energy storage, characterized by their remarkable energy density and cost‐effectiveness. However, the sluggish conversion kinetics of the polysulfide intermediates, compounded with their shuttling behaviors, pose considerable challenges in sulfur electrochemistry. Herein, we develop a novel iron monoboride (FeB) electrocatalyst for boosting sulfur reactions and enhancing Li‐S battery performance. The ultrafine powdery FeB affords abundant and fully exposed active interfaces for host‐guest interactions. Meanwhile, the intrinsic high conductivity of FeB, combined with its strong adsorption and catalytic activity to polysulfides, enables substantial inhibition of the shuttle effect and enhancement of conversion kinetics. As a result, sulfur electrodes equipped with the FeB nanocatalyst realize excellent cyclability with a minimal capacity fading of 0.04 % per cycle over 500 cycles, as well as favorable rate capability up to 7 C. Moreover, decent areal capacity and cycling stability can be also achieved under high‐loading (5.1 mg cm‐2) and limited‐electrolyte (7.0 mL g‐1) configurations. This study presents a facile approach and insightful perspective on nanostructured metal boride for highly efficient sulfur electrocatalysis, holding good promise for the advancement of high‐performance Li‐S batteries.

materials science, multidisciplinary,electrochemistry

Natural Chalcopyrite As a Sulfur Source and Its Electrochemical Performance for Lithium–sulfur Batteries

Chloride‐Reinforced Carbon Nanofiber Host As Effective Polysulfide Traps in Lithium–Sulfur Batteries

Natural Okra Shells Derived Nitrogen‐Doped Porous Carbon to Regulate Polysulfides for High‐Performance Lithium–Sulfur Batteries

Unraveling the Mechanism of Chalcopyrite’s Superior Performance for Lithium Storage

A High-Energy Sulfur Cathode in Carbonate Electrolyte by Eliminating Polysulfides Via Solid-Phase Lithium-Sulfur Transformation

Nanostructured Β-Li3ps4 for All-Solid Lithium-Sulfur Batteries

Natural Vermiculite Enables High‐Performance in Lithium–Sulfur Batteries via Electrical Double Layer Effects

Feasible Catalytic-Insoluble Strategy Enabled by Sulfurized Polyacrylonitrile with In Situ Built Electrocatalysts for Ultrastable Lithium–Sulfur Batteries

Engineering Peculiar Cathode Electrolyte Interphase toward Sustainable and High‐Rate Li–S Batteries

Stable lithium-sulfur batteries with high sulfur content fabricated by ultralight ochroma lagopus-derived carbon with dopamine shell as sulfur host

Enhanced Electrochemical Kinetics with Highly Dispersed Conductive and Electrocatalytic Mediators for Lithium–Sulfur Batteries

High Sulfur Loading of Cathodes for Li-S Batteries

Sulfur-infiltrated porous carbon microspheres with controllable multi-modal pore size distribution for high energy lithium–sulfur batteries

High performance Li-ion sulfur batteries enabled by intercalation chemistry

Enhanced Sulfur Transformation by Multifunctional FeS2/FeS/S Composites for High‐Volumetric Capacity Cathodes in Lithium–Sulfur Batteries

Cobalt Phosphide Nanoflake-Induced Flower-like Sulfur for High Redox Kinetics and Fast Ion Transfer in Lithium-Sulfur Batteries

A Chemically Stabilized Sulfur Cathode for Lean Electrolyte Lithium Sulfur Batteries

Rational Designed Mixed-Conductive Sulfur Cathodes for All-Solid-State Lithium Batteries

Electrode Design with Integration of High Tortuosity and Sulfur-Philicity for High-Performance Lithium-Sulfur Battery

Natural Graphene Microsheets/sulfur As Li-S Battery Cathode Towards >99% Coulombic Efficiency of Long Cycles

Ultrafine Iron Boride as a Highly Efficient Nanocatalyst Expedites Sulfur Redox Electrochemistry for High‐Performance Lithium‐Sulfur Batteries