Abstract:Transverse mechanical properties of titanium matrix composites (TMCs) play an important role during its engineering service. Although SiCf / TC17 composite is one of the most promising TMC candidates for aeroengine, as we know its transverse properties have not been reported yet until now. In this work, the transverse strength of single SiC fiber reinforced TC17 composite was evaluated using cruciform specimen. The surface and cross-section of fractured specimen were investigated by SEM to determine the failure position during tensile test. Finite element simulation method was also used to analyze the mechanism of interfacial failure and crack propagation. During the transverse tensile test of single fiber specimen, the initial non-linearity in the stress-strain curve occurred at the stress of (271 +/- 12) MPa, which indicated the beginning of fiber-matrix interface failure. SEM observation showed that the crack in the center of sample appeared at the interface of reaction layer and carbon coating with a 24 degrees similar to 68 degrees angle to the applied loading direction and its length extended with the increase of the applied stress. The finite element simulation results based on bilinear cohesive element model showed that transverse fracture of composite interface was shear failure mode, which agreed well with the test results. Before the occurrence of non-linearity in the stress-strain curve, the crack initiated at the circular interface between reaction layer and carbon coating with a 40 degrees similar to 50 degrees angle to the applied loading direction. Crack initiation locations in test samples were different with those in simulation samples, because the actual composite interface was rough and some micro-flaws formed in the interface, whereas it was assumed to be an ideal rigid interface for simulation. Then the crack propagated along both circumferential and axial directions because of the shear stress. With the crack growing, the interface close to 0 degrees angle to the applied loading direction failed first caused by the radial tensile stress, whereas the interface near 90 degrees failed later as a result of circumferential shear stress. After complete failure of the interface, stress redistribution occurred around the SiC fiber and the interface separation increased with the increasing of the applied load, which gave rise to the yielding and deforming of the matrix near fiber until the final fracture of the composite.

The Effect of Modulated Matrix Microstructure on the Deformation Behavior in SiCf/Ti17 Composites

Strengthening Effects of Tic Particles and Microstructure Refinement in in Situ Tic-Reinforced Ti Matrix Composites

Microstructure inheritance of matrixes of SiCf/Ti6242 composites from precursor wire coatings by α+β phase field consolidation

Numerical investigations on the hybrid effect and deformation mechanism of TiB2p and TiBw reinforced Cu composites prepared by in-situ mixing casting

The oxide-layer configuration alteration and pseudo-ductile crack propagation mechanisms in composites induced by different relative thicknesses of CVI HfC-SiC multiphase matrix

Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting

Research on Single SiC Fiber Reinforced TC17 CompositesUnder Transverse Tension

Achieving Simultaneous Enhancement of Strength and Ductility in Al Matrix Composites by Employing the Synergetic Strengthening Effect of Micro- and Nano-Sicps

Microstructural Characteristics and Mechanical Behavior of SiC(CNT)/Al Multiphase Interfacial Micro-Zones Via Molecular Dynamics Simulations

Effects of Degree of Deformation on the Microstructure, Mechanical Properties and Texture of Hybrid-Reinforced Titanium Matrix Composites

Development of Microstructure in Submicron Particles Reinforced Magnesium Matrix Composite Processed by Room Temperature Deformation

3D Microstructure-based Finite Element Modeling of Deformation and Fracture of SiCp/Al Composites

Microstructure and properties of SiCw/6061 aluminium alloy composites after compression at temperatures around solidus of matrix

An enhanced fem model on the deformation behavior of sic / aluminum composites

Effects of configuration parameters on the deformation and fracture behaviors of TiB2/Cu composites with network structure: A numerical approach using an enhanced finite element model

Microstructure and Compressive Properties Ofin SituSynthesized TiC/Ti Composites

Matrix microstructure evolution during the fabrication of SiCf/Ti60 composites

Influence of deformation parameters and network structure to the microstructure evolution and flow stress of TiBw/Ti64 composite

The effect of deformation parameters on the dynamic recrystallization and microstructure evolution of the quasi-continuous network reinforced TiAl/B 4 C composites

Effect of extrusion treatment on the microstructure and mechanical behavior of SiC nanowires reinforced Al matrix composites

Effects of Configuration Parameters on the Deformation and Fracture Behaviors of TiBM <sub>2</sub>/cu Composites with Network Structure: A Numerical Approach Using an Enhanced Finite Element Model