Abstract:A lithium-sulfur (Li-S) battery has a high theoretical specific capacity (1675 mAh g-1 of elemental sulfur) and a high nominal energy density (2500 Wh kg-1 of cell weight), which offers the prospect of a significant energy density improvement compared to the mainstream lithium-ion batteries (150 Wh kg-1). However, the development of Li-S battery technology has been plagued by problems arising from the highly insulating nature of sulfur (5×10-30 S cm-1 at 25 °C), the high solubility of lithium polysulfides in the electrolyte and volumetric expansion of sulfur during lithiation. Here, we demonstrate the design and preparation of few-layer graphene (FLG) foam scaffold for sulfur loading to fabricate cathode structures for lithium-sulfur batteries. In this work, a free-standing FLG monolithic network foam was formed as a negative of a Ni metallic foam template by CVD followed by etching away of Ni. Then, a three-dimensional (3-D) cathode system for lithium sulfur (Li-S) batteries has been synthesised by loading sulfur on to this interconnected network of few-layered graphene (FLG) via a sulfur solution infiltration method. This cathode system did not require any additional binding agents, conductive additives or a separate metallic current collector thus decreasing the weight of the cathode by typically ~20-30 wt%. A Li-S battery with the sulfur/FLG foam cathode shows good electrochemical stability and high rate discharge capacity retention for up to 400 discharge/charge cycles at a high current density of 3200 mA g-1, which due to the FLG foam offers excellent electrical conductivity, an appropriate pore structure for containing the electro-active sulfur and facilitates rapid electron/ion transport. Even after 400 cycles the capacity decay is only ~0.064% per cycle relative to the early (e.g. the 5th cycle) discharge capacity, while yielding an average columbic efficiency of ~96.2%. To further understand the sulfur loading ability of FLG foam, the composites with high content (up to 72 wt %) were also investigated. The composite with high content of sulfur still presented good initial discharge capacity and good cycle stability after 200 cycles. Our results indicate the potential suitability of graphene foam for efficient and high-performance batteries.

A light-weight free-standing graphene foam-based interlayer towards improved Li-S cells

A Freestanding Flexible Single‐Atom Cobalt‐Based Multifunctional Interlayer Toward Reversible and Durable Lithium‐Sulfur Batteries

Structural and Surfacial Modification of Carbon Nanofoam as an Interlayer for Electrochemically Stable Lithium-Sulfur Cells

Enhanced cycle performance of Li/S battery with the reduced graphene oxide/activated carbon functional interlayer

Enhanced Cycle Performance in a Binder Free Lithium Sulfur Battery Using Few-Layer Graphene Foam Scaffold

Bioderived carbon fiber conductive networks with inlaid electrocatalysts as an ultralight freestanding interlayer for working Li–SeS2 pouch cells

Free-standing graphene/polyetherimide/ZrO2 porous interlayer to enhance lithium-ion transport and polysulfide interception for lithium-sulfur batteries

Enhanced Cycling Performance for Lithium–Sulfur Batteries by a Laminated 2D g‐C3N4/Graphene Cathode Interlayer

Binder Free Three-Dimensional Sulphur/few-Layer Graphene Foam Cathode with Enhanced High-Rate Capability for Rechargeable Lithium Sulphur Batteries

Enhanced Cycling Performance for Lithium-Sulfur Batteries by a Laminated 2D g-C N /Graphene Cathode Interlayer.

Ultrafine Co-Species Interspersed g-C3N4 Nanosheets and Graphene as an Efficient Polysulfide Barrier to Enable High Performance Li-S Batteries

Ultra-small Self-Discharge and Stable Lithium-Sulfur Batteries Achieved by Synergetic Effects of Multicomponent Sandwich-Type Composite Interlayer

Atom-Thick Interlayer Made of CVD-Grown Graphene Film on Separator for Advanced Lithium-Sulfur Batteries.

Freestanding Agaric-Like Molybdenum Carbide/graphene/n-Doped Carbon Foam As Effective Polysulfide Anchor and Catalyst for High Performance Lithium Sulfur Batteries

Fe3O4-Decorated Porous Graphene Interlayer for High-Performance Lithium-Sulfur Batteries

Strutted Graphene Foam Loading Sulfur for High-Rate Long-Lifetime Li-S Batteries

Electrocatalytic Interlayer with Fast Lithium–Polysulfides Diffusion for Lithium–Sulfur Batteries to Enhance Electrochemical Kinetics under Lean Electrolyte Conditions

Graphene-based Fe-coordinated framework porphyrin as an interlayer for lithium–sulfur batteries

A Feather-like Interlayer Design with Highly Exposed Active Sites for High-Performance Lithium-sulfur Batteries

Light-weight functional layer on a separator as a polysulfide immobilizer to enhance cycling stability for lithium–sulfur batteries

Sulfonic Groups Originated Dual-Functional Interlayer for High Performance Lithium-Sulfur Battery