Abstract:As the third generation solar cell,dye-sensitized solar cells (DSSCs) have attracted tremendous amount of interest in scientific research and industrial applications during the past 25 years because of their simple production procedures,low-cost,environmental friendliness of raw materials,and relatively high power conversion efficiency (PCE).As an important component,counter electrode (CE) not only transfers electrons flowing from the external circuit to the electrolyte,but also catalyzes the reduction of oxidized electrolyte at the CE/electrolyte interface.So far,Pt as a noble metal has been the most commonly used CE for laboratory research due to its excellent electrocatalytic activity,high conductivity and good chemical stability.Unfortunately,the high cost and low abundance ratio of Pt create a big obstacle for large-scale applications of DSSCs.Therefore,exploiting Pt-free CE materials with high electrocatalytic activity and low cost is vital for the practical applications.Recently,a lot of Pt-free materials,such as graphene,carbon,conductive polymers and metal compounds (including carbide,oxide,sulfide,nitride and selenide),have been proposed for use as the CE of DSSCs.Among those materials,metal selenides have drawn great interest due to their distinctive electronic structures,interesting chemical behaviors and distinctive physical properties.The electrocatalytic activity of a substance not only depends on the chemical composition but also relies on the morphology of materials.While the investigation on developing new electrocatalysts has been extensively conducted,the morphology effect on the electrocatalytic activity has rarely been studied.In this paper,a simple low temperature hydrothermal method was used to synthesize NiSe2 with nanorod (r-NiSe2) and nanoparticle (p-NiSe2) morphologies.A drop-cast method was used to fabricate CE films without any post-treatment.Since the only difference for those two CEs used in DSSC is their morphology,it allows us to study the morphology effect on the electrocatalytic activity and solar cell performances.By changing the drop-cast times,the loading amount from 5.0 to 80.0 μg/cm2 could be controlled.The PCE of DSSCs increases with increasing the loading amount up to 10 μg/cm2 and then decreases with further increasing the loading amount of NiSe2.Thus,the best loading amount has been determined to be 10 μg/cm2.All the measurements in this paper are based on the best loading amount.The DSSC with r-NiSe2 CE achieves PCE of 8.52％,which is higher than that for the p-NiSe2 based DSSC (8.13％) and even better than the Pt based DSSC (8.20％) at comparable conditions.This indicates that NiSe2 nanorod is better than NiSe2 nanoparticle as the CE of DSSCs towards higher photovoltaic performance.To elucidate the catalytic activity of r-NiSe2 and p-NiSe2,electrochemical impedance spectroscopy,Tafel polarization curve and cyclic voltammetry were conducted.The experimental results indicate that the r-NiSe2 CE exhibits higher electrocatalytic activity than p-NiSe2 CE,which explains the reason that the DSSC based on r-NiSe2 CE has the higher PCE than the p-NiSe2 CE.The result implies that by varying the morphologies of CE materials could also fulfill the improvement of solar cell's performance.

Photovoltaic Counter Electrodes: an Alternative Approach to Extend Light Absorption Spectra and Enhance Performance of Dye-Sensitized Solar Cells

Efficient Ag8ges6 Counter Electrode Prepared From Nanocrystal Ink For Dye-Sensitized Solar Cells

Efficient Counter Electrode Manufactured from Ag2s Nanocrystal Ink for Dye-Sensitized Solar Cells

Two-Dimensional Transition Metal Dichalcogenides-Based Counter Electrodes for Dye-Sensitized Solar Cells

Transparent MoS<sub>2</sub>/PEDOT Composite Counter Electrodes for Bifacial Dye-Sensitized Solar Cells

Metal Selenides as Efficient Counter Electrodes for Dye-Sensitized Solar Cells.

Octahedron Shaped Lead Sulfide Nanocrystals As Counter Electrodes for Quantum Dot Sensitized Solar Cells

Design of Amorphous ZnWSe2 Alloy-based Counter Electrode for Highly Efficient Dye-Sensitized Solar Cells

Antimony tin oxide/lead selenide composite as efficient counter electrode material for quantum dot-sensitized solar cells

Effect of Different Counter Electrodes on Power Conversion Efficiency of DSSCs

Selenylation to charge transfer improvement at the counter electrode (CE)/electrolyte interface for nanocrystalline Cu1.8S1- xSex CEs

Highly Efficient Dye-Sensitized Solar Cells with NiSe2 Counter Electrodes: Effect of Morphology on the Electrocatalytic Activity and the Photovoltaic Performance

Development of binary transition metallic selenide (NiSe/Co3Se4) hybrid counter electrode for highly efficient Pt-free dye-sensitized solar cells

High-performance Dye-Sensitized Solar Cells Using Ag-doped CoS Counter Electrodes

Ultrasonic Remove of Particle Aggregation in Carbon Based Counter Electrodes for Dye-Sensitized Solar Cells

Efficient Dye-Sensitized Solar Cells with Cose/Graphene Composite Counter Electrodes

CoSe2@N-Doped Graphene Nanocomposite High-Efficiency Counter Electrode for Dye-Sensitized Solar Cells

Efficient Flexible Counter Electrode Based on Modified Graphite Paper and in Situ Grown Copper Sulfide for Quantum Dot Sensitized Solar Cells

Cobalt Selenide Hollow Nanorods Array with Exceptionally High Electrocatalytic Activity for High-Efficiency Quasi-Solid-state Dye-Sensitized Solar Cells

Cobalt selenide/tin selenide hybrid used as a high efficient counter electrode for dye-sensitized solar cells

MOF-derived CuxS double-faced-decorated carbon nanosheets as high-performance and stable counter electrodes for quantum dots solar cells