Abstract:Low-temperature multi-effect distillation that employs horizontal tube falling film evaporation technology is one of the most promising desalination methods with advantage of high heat transfer coefficient at low temperature,low waterspray density and small heat transfer temperature difference.Falling film evaporators have been widely used in absorbtype chillers,desalination devices and other areas.In a horizontal tube falling film evaporator,water and steam were flowed in different directions.The vertical falling film flow was driven by gravity,whereas the steam flow across the tube bundle was driven by pressure difference.Hence,the pressure drop and the consequent temperature drop of the steam are not only caused by the tube bundle but also by the falling water.In this paper,the effects of parameters such asspray density were determined.Experimental measurement of pressure drop data during the saturated steam flowing across aluminum brass tube bundles was carried out.The pressure drop coefficient was obtained from the experimental data.The rotated square-arranged tube bundle was chosen as a physical model to calculate the steam temperature difference drop on falling film evaporation.Based on the experimental data,the fitting pressure drop coefficient was employed in this calculation.The numerical codes were developed to simulate the steady-state performance of temperature difference drop in horizontal tube falling film evaporation.The iterative procedure was required based on the initial values with a close chain of equations and parameters.The solution was obtained through a step-by-step method,This quantitative temperature difference drops caused by the pressure drop can be calculated by the solution.The influences of spray density,saturated temperature,and tube column number on vapor temperature difference drop were analyzed respectively.The temperature difference drop caused by the pressure drop will decrease the temperature difference.The effect of temperature difference drop can be analyzed in two aspects.On the one hand,the temperature difference drop directly reduces the difference in heat transfer temperature,and thus,decreases heat transfer rate;on the other hand,the temperature difference drop generally increases the heat transfer coefficient under a certain heat transfer flux.When temperature difference drop is considered in a calculation,the heat transfer coefficient can be derived more accurately.Moreover,an accurate calculation of the temperature difference drop can provide a more detailed analysis on the influence factors of the heat transfer coefficient.At a certain tube arrangement and the same steam flow flux,the results showed that the temperature difference drop increases with the increase of spray density.It can be showed that the temperature difference drop at 50℃ is 3.5 times of that at 70℃.However,the temperature difference drop decreases with the increase of saturated temperature.The temperature difference drop at spray density of 0.08 kg/(m s) is almost double of that at spray density of 0.02 kg/(m s).The calculations also show that the temperature difference drop is in parabolic rise with the increase of tube column number.When the temperature difference drop is set at lower than 0.3℃,the maximum tube column (Nmax) can be obtained.The results showed that the Nmax increases with increasing saturated temperature,but decreases with increasing spray density.The Nmax can be employed to determine the heat transfer area for optimization design of the heat exchanger.

Effect of the tube surface temperature on the seawater fouling process during falling film evaporation outside horizontal tubes

Study on the Performance of a Scale Inhibitor During Horizontal-Tube Falling Film Evaporation of Seawater

Experimental Study on CaCO3 Fouling Characteristics During Falling Film Evaporation

Impact of Tube Surface Properties on Crystallization Fouling in Falling Film Evaporators for Seawater Desalination

Scale Formation and Mitigation of Mixed Salts in Horizontal Tube Falling Film Evaporators for Seawater Desalination

Experimental study of falling film evaporation heat transfer outside horizontal tubes

Experimental Studies on Heat Transfer Coefficients of Horizontal Tube Falling Film Evaporation with Seawater

Heat transfer characteristics of horizontal tube falling film evaporation for desalination

Investigation on heat transfer performance of corrugated tubes in low-temperature multi-effect falling-film evaporation

Analysis of special heat transfer phenomenon outside horizontal-tube falling film evaporation for sea water

Numerical Investigation on Characteristics of Falling Film in Horizontal-Tube Falling Film Evaporator

Fouling on Aluminum-Brass and Titanium Tube Surface in Environment of Low-Temperature Multi-Effect Distillation for Desalination

Effects of Temperature and Salinity on Fouling in Hypersaline Seawater

Experimental Study of Falling Film Evaporation Heat Transfer Coefficient on Horizontal Tube

Experimental Research of Horizontal Tube Falling Film Evaporation in Desalination

Numerical Simulation and Performance Analysis of Horizontal-Tube Falling-Film Evaporators in Seawater Desalination

Numerical study on the flow and heat-transfer characteristics of horizontal finned-tube falling-film evaporation: Effects of liquid column spacing and wettability

Heat Transfer Temperature Difference Drop on Falling Film Evaporation of Horizontal Tube Bundle in Rotated Square-Arranged

Study on the Superhydrophilic Modification and Enhanced Corrosion Resistance Method of Aluminum Alloy Distillation Desalination Tubes

A correlation of heat transfer for falling film evaporation on the horizontal tube with multiple-precision expansion method

Thermal Analysis of Internal Condensation Process in a Horizontal Tube of Falling Film Evaporation