Fabrication of agricultural waste supported UiO-66 nanoparticles with high utilization in phosphate removal from water

Hui Qiu,Meichen Ye,Qingqing Zeng,Wenlu Li,John Fortner,LeLe Liu,Luyang Yang

DOI: https://doi.org/10.1016/j.cej.2018.12.017

IF: 15.1

2019-01-01

Chemical Engineering Journal

Abstract:A water stable UiO-66 nanoparticle confined in agricultural wastes with enhanced reactivity and improved adsorption selectivity for phosphate adsorption.

What problem does this paper attempt to address?

Fabrication of a Biomass-Based Hydrous Zirconium Oxide Nanocomposite for Preferable Phosphate Removal and Recovery

hui qiu,chen liang,xiaolin zhang,mindong chen,yunxia zhao,tao tao,zhengwen xu,gang liu

DOI: https://doi.org/10.1021/acsami.5b06098

IF: 9.5

2015-01-01

ACS Applied Materials & Interfaces

Abstract:Advanced removal of phosphate by low-cost adsorbents from municipal wastewater or industrial effluents is an effective and economic way to prevent the occurrence of eutrophication. Here, we proposed a novel method to immobilize hydrous zirconium oxide nanoparticle within quaternary-aminated wheat straw, and obtained an inexpensive, eco-friendly nanocomposite Ws–N–Zr. The biomass-based Ws–N–Zr exhibited higher preference toward phosphate than commercial anion exchanger IRA-900 when competing sulfate ions coexisted at relatively high levels. Such excellent performance of Ws–N–Zr resulted from its specific hybrid structure, the quaternary ammonium groups bonded on the host favor the preconcentration of phosphate ions inside the wheat straw based on Donnan effect, and the encapsulated HZO nanoparticle exhibits preferable sequestration of phosphate ions through specific interaction, as further demonstrated by FTIR and X-ray photoelectron spectroscopy. Cycle adsorption and regeneration experiments demonstrated ...
Fabrication and evaluation of a regenerable HFO-doped agricultural waste for enhanced adsorption affinity towards phosphate

Hui Qiu,Wenxiang Ni,Haihan Zhang,Kai Chen,Jiacheng Yu

DOI: https://doi.org/10.1016/j.scitotenv.2019.135493

2020-02-10

Abstract:Chemical modification of agricultural waste biomass has proved to be an economy and effective approach to capture phosphate ions, except for that under acidic conditions and highly competitive ion systems. According to this, a new nanocomposite (HFO@St+) was fabricated by incorporating nano-sized hydrous Fe(III) oxides (HFO) within aminated wheat straw in order to overcome the bottleneck. The optimal pH of phosphate uptake by HFO@St+ was greatly broadened and observed over a wide pH range between 2.0 and 7.0. The binary exchange reaction indicated that phosphate was strongly and preferably adsorbed by HFO@St+ with the separation factor K of phosphate over nitrate increasing from 0.23-1 or 0.20-0.26 to 2.5-38 or 2.5-15 for near neutral or acidic pHs, respectively. The sorption selectivity for HFO@St+ followed the order of phosphate > nitrate > chloride under experimental conditions. The presence of inorganic and organic ligands (SO4 and HA) showed no significant effect on phosphate adsorption. XPS and FT-IR analyses were performed to explore the underlying mechanism of adsorption. The exhausted material could be regenerated with NaOH-NaCl solution for at least ten cycles, indicating that HFO@St+ can be used as a sustainable biomass product with excellent adsorption affinity for phosphate removal.
The Novel Performance and Adsorption Mechanism of Synthesized Modified Zirconium-Based Metal-Organic Frameworks for Resource Recovery from Wastewater

Muhammad Naveed Afridi,Jingwen Wang,Aziz-Ur-Rahim Bacha,Zulakha Zafar,Syed Taj Ud Din,Muhammad Qasim,Fazal Maula Khan,Chaolin Li

DOI: https://doi.org/10.1016/j.jiec.2024.09.009

IF: 6.76

2024-01-01

Journal of Industrial and Engineering Chemistry

Abstract:Phosphorous (P) is an indispensable nutrient popularly employed to fertilize agricultural farms. However, its overuse in farming leads to excessive discharge in agricultural runoff, causing eutrophication. To prevent harm to the environment, it is necessary to remove P from wastewater. Adsorption is one of the ways to achieve this goal. In this study, using a solvothermal process, UiO-66-NH2 was successfully modified/codoped with aluminum (Al) and magnesium (Mg). The Al/Mg-codoped UiO-66-NH2 was characterized using scanning electron microscopy, X-ray diffraction, transmission electron microscopy, Fourier-transform infrared spectroscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The study also investigated various adsorption factors, including temperature, pH, initial phosphate concentration, sorbent dosage, reaction time, and coexisting components. The findings demonstrated that the sorption process was predominantly based on chemical interactions, as evidenced by the Langmuir model (R2 > 0.99) and pseudo-second order (R2 > 0.99) analyses that fit well with experimental findings. The sorption capacity value was determined to be 117.6 mg P/g or 360.73 mg PO4/g. Thermodynamic results suggested the spontaneous and endothermic nature of P uptake process. Additionally, this research demonstrated the effective utilization of adsorbent for up to six regeneration cycles and recovery of adsorbed P using sodium hydroxide.
Filter fabrication by constructing metal-organic frameworks membrane on waste maize straw for efficient phosphate removal from wastewater

De-Chang Li,Qian Zhang,Wen-Quan Wang,Guang-Hui Wang

DOI: https://doi.org/10.1016/j.cej.2022.136461

IF: 15.1

2022-09-01

Chemical Engineering Journal

Abstract:Metal-organic frameworks (MOFs) have been demonstrated as effective adsorbents for removal of phosphate from wastewater, but the difficulty in processing and recycling of powdery MOFs limits their practical application. Shaping MOFs into application-oriented forms meanwhile maintaining their intrinsic property is important but challenging. Here, a novel UiO-66/MS filter is fabricated by constructing UiO-66 membrane on the cell wall of waste maize straw (MS) through a solvothermal process. The unique biological structure of MS provides well-developed channels for mass transfer, and the UiO-66 nanoparticles are uniformly anchored on the cell walls of MS to form a monolayer membrane, promoting the exposure of adsorption sites. Due to these structural advantages, the UiO-66/MS filter exhibits higher efficiency for phosphate removal from water than UiO-66 pellet. To realize continuous phosphate removal, an all-in-one device is fabricated by connecting UiO-66/MS filters in series, over which the residual P content (initial P = 3.0 mg·L−1) in the effluent still meets the primary (<0.5 mg·L−1 at 300 L·m−2·h−1) and secondary (<1.0 mg·L−1 at 800 L·m−2·h−1) standards of China's integrated wastewater discharge standard. This study not only provides an efficient UiO-66/MS filter for phosphate remediation, but also provides a blueprint for value-added utilization of the waste MS.

engineering, chemical, environmental
Dynamics and Treatability of Heavy Metals in Pig Farm Effluent Wastewater by Using UiO-66 and UiO-66-NH2 Nanomaterials as Adsorbents

Leiping Wang,Xiaorong Dai,Zun Man,Jianrong Li,Yifeng Jiang,Dezhao Liu,Hang Xiao,Sanjay Shah

DOI: https://doi.org/10.1007/s11270-021-05229-6

2021-07-01

Abstract:Concentrated pig production is a major source of environmental pollution. Metal–organic frameworks (MOFs) show potential for reducing heavy metal pollution. Two zirconium-based octahedral MOFs, UiO-66 and UiO-66-NH2, were prepared by solvothermal method and were characterized by XRD, SEM, FT-IR, and BET. The adsorption capacity, treatability, and reusability of the adsorbents were tested in batch experiments. The optimum adsorbent dosage was 4 g/L, and the maximum removal rates at room temperature of chromium (Cr), manganese (Mn), iron (Fe), nickel (Ni), and Arsenic (As) on UiO-66 were 76.93%, 93.73%, 88.81%, 83.30%, and 86.11%, respectively. In the kinetic experiments, the adsorption process achieved equilibrium within 90 min and generally conformed to the quasi-second kinetics model. The results demonstrated that UiO-66 and UiO-66-NH2 can be used over a wide range of pH for removal of most HMs on a large scale. Meanwhile, the adsorbents maintained excellent adsorption capacity after at least 3 cycles. Overall, UiO-66 and UiO-66-NH2 have a high potential for practical application on the recovery of heavy metals in the complex wastewater from animal farms.
Size Modulation of Zirconium-Based Metal Organic Frameworks for Highly Efficient Phosphate Remediation.

Yue Gu,Donghua Xie,Yue Ma,Wenxiu Qin,Haimin Zhang,Guozhong Wang,Yunxia Zhang,Huijun Zhao

DOI: https://doi.org/10.1021/acsami.7b10024

IF: 9.5

2017-01-01

ACS Applied Materials & Interfaces

Abstract:Eutrophication of water bodies caused by the excessive phosphate discharge has constituted a serious threaten on a global scale. It is imperative to exploit new advanced materials featuring abundant binding sites and high affinity to achieve highly efficient and specific capture of phosphate from polluted waters. Herein, water stable Zr-based metal organic frameworks (MOFs, UiO-66) with rational structural design and size modulation have been successfully synthesized based on a simple solvothermal method for effective phosphate remediation. Impressively, the size of the resulting UiO-66 particles can be effectively adjusted by simply altering reaction time and the amount of acetic acid with the purpose of understanding the crucial effect of structural design on the phosphate capture performance. Representatively, UiO-66 particles with small size demonstrates 415 mg/g of phosphate uptake capacity, outperforming most of the previously reported phosphate adsorbents. Meanwhile, the developed absorbents can rapidly reduce highly concentrated phosphate to below the permitted level in drinking water within a few minutes. More significantly, the current absorbents display remarkable phosphate sorption selectivity against the common interfering ions, which can be attributed to strong affinity between Zr-OH groups in UiO-66 and phosphate species. Furthermore, the spent UiO-66 particles can be readily regenerated and reused for multiple sorption-desorption cycles without obvious decrease in removal performance, rendering them promising sustainable materials. Hence, the developed UiO-66 adsorbents hold significant prospects for phosphate sequestration to mitigate the increasingly eutrophic problems.
[Fabrication of a Biomass-Based Hydrous Zirconium Oxide Nanocomposite for Advanced Phosphate Removal].

Hui Qiu,Zhi-Feng Qin,Feng-Ling Liu,Chen Liang,Ming-Xia Song,Zheng-Wen Xu,Yi-Dong Guan

DOI: https://doi.org/10.13227/j.hjkx.201706118

2018-01-01

Abstract:Wheat straws were modified by 3-chloro-2-hydroxypropyl trimethylammonium chloride (CTA) to obtain aminated wheat straw St-N'. The optimum synthetic conditions were determined to be NaOH with 30% mass fraction, CTA of 100 mL, reaction temperature of 80℃, and reaction time of 3 h, which was verified by orthogonal experiments. Nano-sized hydrous zirconium oxides (HZO) were immobilized into St-N' by an in situ precipitation method to obtain the nanocomposite St-N'-Zr. The SEM, TEM, XRD, and BET results indicated that the nano-sized HZO with 50-100 nm sizes were uniformly loaded onto the inner surface of the biomass-based carrier St-N' that was amorphous in nature. A Langmuir adsorption isotherm fitted the adsorption process well, and the maximum adsorption amount was calculated to be 33.90 mg·g-1. The optimal pH range was 1.8-6.0, displaying good removal capacity of phosphate in acidic waters. In the presence of high levels of competing anions, the phosphate adsorption still retained more than 70% of the original amount, showing the higher preference of St-N'-Zr towards phosphate than towards the commercial anion exchanger D-201. After 10 cycles of adsorption-desorption, the removal efficiency remained stable, confirming the good regeneration ability and potential application of St-N'-Zr.
Preferable Phosphate Sequestration by Nano-La(iii) (hydr)oxides Modified Wheat Straw with Excellent Properties in Regeneration

Hui Qiu,Chen Liang,Jianghua Yu,Qingrui Zhang,Mingxia Song,Fenghua Chen

DOI: https://doi.org/10.1016/j.cej.2017.01.043

IF: 15.1

2017-01-01

Chemical Engineering Journal

Abstract:Enhanced removal of phosphate by biomass-supported adsorbents is an effective and economic method to prevent the accelerated eutrophication in water body. A new nanocomposite Ws-N-La is fabricated for efficient phosphate removal by immobilizing “rod-like” nano-sized La(III) (hydr)oxides within a quaternary-aminated wheat straw (Ws-N). It exhibits higher adsorption capacity towards phosphate than the commercial IRA-900 or HFO-201 even at higher competing anions levels. The pH result indicated that the Ws-N-La would effectively sequestrate phosphate over a wide pH range between 3.0 and 7.0 without significant La(III) leaching. Ten cycles of adsorption-desorption experiments reveals that no significant capacity loss is observed, indicating excellent stability and repeated use property than any other La(III)-based adsorbents. The results of TEM, XRD and XPS analysis demonstrated that the formation of “needle-like” lanthanum phosphate nanoparticle is the dominant pathway for the specific adsorption of phosphate by nano-La(III) (hydr)oxides. All the results suggested that the biomass-supported nano-composite Ws-N-La can serve as a promising adsorbent for preferable phosphate removal in realistic application.
Integrated fabrication of CMC@UiO-66–NH 2 @PEI composite adsorbents for efficient batch and dynamic phosphate capture

Yuyang Liu,Qingda An,Zuoyi Xiao,Jingai Hao,Xiaoling Dong,Kairuo Zhu,Shangru Zhai,Chang-Sik Ha

DOI: https://doi.org/10.1039/d3ew00685a

2024-01-01

Abstract:A separable bio-adsorbent was created through a straightforward cross-linking process, leading to effective capture of phosphate in both static and dynamic aqueous systems.

environmental sciences,engineering, environmental,water resources
Nano-Fe2O3/bentonite Complexes for Enhanced Phosphorus Removal from Industrial Wastewater

Huawei Wu,Yuan Liu,Mei Huang

DOI: https://doi.org/10.2991/icsmim-15.2016.141

2016-01-01

Abstract:Nano-Fe2O3/bentonite complexes were prepared through a reaction between the iron salt solution and the dispersion solution of refined bentonite, and their degradation capability for phosphorus removal was investigated. The results show that Fe2O3 nanoparticles anchored between bentonite layers have enhanced capacity for phosphorus removal. Under the conditions of OP0=10.76 mg/L, IP0=0.93mg/L and pH=3, nano-Fe2O3/bentonite complexes were successfully applied in the treatment of industrial phosphorous wastewater. And the corresponding degradation rate of TP reaches 82% in 0.5hr.
Multifunctional Fe3O4/TiO2/NH2-UiO-66 with integrated interfacial features for favorable phosphate adsorption

Liyu Yang,Shangui Zhang,Xiangcheng Shan,Chang-sik Ha,Qingda An,Zuoyi Xiao,Li Wei,Shangru Zhai,C.S. Ha,Wei Li

DOI: https://doi.org/10.1039/d2nj02852b

IF: 3.3

2022-06-24

New Journal of Chemistry

Abstract:Excessive use and discharge of phosphate are the decisive factors leading to water eutrophication, and adsorption is deemed among the most effective methods in phosphorus capture. This study prepared the multifunctional synergistic adsorbent (Fe3O4/TiO2/NH2-UiO-66) by hydrothermal method. The interface assembly of TiO2 and zirconium-based metal-organic frameworks with octahedral-like (NH2-UiO-66) enhanced the adsorption performance of the adsorbent for phosphate, and can reach 192.334 mg/g. The Langmuir adsorption isotherms, pseudo-second-order kinetics, and thermodynamics findings showed that the adsorption belongs to monolayer chemisorption and spontaneous endothermic process. After five cycles of adsorption experiments could still maintain more than 80% of the initial adsorption capacity. FT-IR, XPS, and DFT analysis proved that the adsorbent was bonded by inner-sphere complexation and ligand exchange mechanisms with phosphate. Under acidic conditions, the amino group was protonated to form an ammonium ion, adsorbed by electrostatic attraction with phosphate. Different from previous studies, the synergistic action between the interface of TiO2 and NH2-UiO-66 can act as a "claw" for capturing phosphate and exhibits efficient adsorption capacity and pH adaptability for phosphate. It is expected to be well applied in practical water treatment.

chemistry, multidisciplinary
Fabrication of amorphous metal-organic framework in deep eutectic solvent for boosted organophosphorus pesticide adsorption

Yaqi Yin,Chen Fan,Yuwei Shan,Linru Cheng

DOI: https://doi.org/10.1016/j.jece.2023.109963

IF: 7.7

2023-04-20

Journal of Environmental Chemical Engineering

Abstract:Herein, we describe a new and sustainable strategy of directly constructing the amorphous metal-organic framework (MOF) through the use of deep eutectic solvent (DES) for the highly effective and efficient adsorption of organophosphorus pesticide from contaminated water. The as-obtained products possessed nanosize morphology (as small as 40 nm), hierarchical pores ranging from 1.16 to 12.3 nm, high porosity up to 0.5954 cm 3 g -1 , and abundant unsaturated metal centers. The presence of structural disorder increased the number of active sites and promoted the diffusion of target molecules, leading to enhance host-guest interactions. These properties were beneficial for the application of the material in the enrichment adsorption of profenofos. The amorphous UiO-66 with the highest content of defect disorder (4.408) displayed a remarkably high affinity toward profenofos, resulting in an exceptional adsorbate uptake capacity over 1300 mg·g -1 . This is a three-fold enhancement compared to its crystalline counterpart. And its performance surpassed that of most previously reported absorbents. Additionally, the adsorption behavior and mechanism of amorphous UiO-66 toward profenofos were elucidated by high-revolution X-ray photoelectron spectroscopy (XPS) and various models. The results revealed a multi-layer heterogeneous adsorption, involving multiple sorption process. The profenofos adsorption mechanisms over amorphous UiO-66 mainly rely on hydrogen bonding, Zr-O-P bonds, and P-Zr bonds. Moreover, the amorphous UiO-66 exhibited outstanding regeneration and reusability characteristics, making it a stable and promising adsorbent for water remediation. Its efficient and rapid removal of pollutants holds great potential for practical applications, while also providing guidelines for the design and optimization of next-generation sorbent.

engineering, chemical, environmental
Enhanced low-concentration phosphate adsorption using magnetic UiO-66@Fe3O4 composite with potential linker exchange

Xiaochang Lin,Bo Sun,Pengsen Wang,Min Zhao,Dejia Liu,Qiyu Zhang,Baile Wu,Dezhao Liu

DOI: https://doi.org/10.1016/j.chemosphere.2024.143126

IF: 8.8

Chemosphere

Abstract:A magnetic FenUiO-66 adsorbent was created to achieve high phosphate adsorption capacity. The incorporation of Fe3O4 facilitated the precipitation and growth of UiO-66 during crystallization, resulting in a shift towards a multilayer heterogeneous distribution of adsorption sites. The increased Fe3O4 content notably enhanced the magnetic properties of FenUiO-66, while negligibly affecting its adsorption performance. The Fe1.5UiO-66 demonstrated exceptional phosphate adsorption capacity (136.54 mg/g), outstanding selectivity, and sustained reusability, with an 80% removal efficiency after nine cycles of treating actual water. The mechanism of phosphate adsorption by FenUiO-66 involved electrostatic attraction, ligand exchange, and linker exchange. Notably, while linker exchange significantly contributed to high adsorption capacity, it resulted in irreversible damage to the FenUiO-66 crystal. These unequivocal findings will serve as a solid foundation for further research and underline the critical role of linkers in the process of phosphate adsorption.
Yttrium-doped MOFs for efficient phosphate adsorption: Electrochemical properties, electro-assisted desorption, and mechanism study

Zhuangzhuang Bi,Zhaoneng Wan,Guang Li,Muhan Chen,Zhangjie Huang

DOI: https://doi.org/10.1016/j.seppur.2024.126845

IF: 8.6

2024-02-24

Separation and Purification Technology

Abstract:Metal-organic frameworks (MOFs) are effective adsorbents for phosphate removal, but it is challenging to use them to treat the eutrophication of natural water bodies due to their harsh synthesis conditions and poor regeneration performance. In this study, the microstructure and electronic structure of UiO-66-NH 2 were modulated by doping yttrium (Y) at room temperature to enhance the number of oxygen vacancies, ligand deficiency, and number of exposed metal sites. Compared with the conventional hydrothermal route, the doping process did not require a high temperature, resulting in low material preparation costs. The obtained 1Y-UiO-66-NH 2 exhibited a smaller particle sizes, higher porosity, and more unsaturated coordination sites, which improved the phosphorus adsorption efficiency. The 1Y-UiO-66-NH 2 achieved an optimum adsorption capacity of 104 mg P/g at 298 K. Over a wide pH range of 4–8, 1Y-UiO-66-NH 2 maintained a high P adsorption capacity in the presence of interfering ions, demonstrating its excellent stability and anti-interference ability. Spectroscopy, electrochemical measurements, and density functional theory calculations revealed that binding between 1Y-UiO-66-NH 2 and phosphate mainly involved coordination exchange, electrostatic adsorption, hydrogen bonding, and the occupation of defect sites. The regeneration ability of 1Y-UiO-66-NH 2 was studied by electro-assisted desorption, which showed that the desorption efficiency of phosphate on 1Y-UiO-66-NH 2 exceeded 90 % at a constant voltage of −3 V. After five adsorption–desorption cycles, 1Y-UiO-66-NH 2 maintained adsorption capacity of 78.52 mg P/g. The proposed method has good application prospects for treating the eutrophication treatment of natural water bodies.

engineering, chemical
Utilization and value-adding of waste: Fabrication of porous material from chitosan for phosphate capture and energy storage

Xutao Tang,Shanjuan Zhao,Huan Xie,Yongmin Zhang

DOI: https://doi.org/10.1016/j.ijbiomac.2024.131944

Abstract:Efficient removal and recycling of phosphorus from complex water matrices using environmentally friendly and sustainable materials is essential yet challenging. To this end, a novel bio-based adsorbent (DX-FcA-CS) was developed by coupling oxidized dextran-crosslinked chitosan with ferrocene carboxylic acid (FcA). Detailed characterization revealed that the incorporation of FcA reduced the total pore area of DX-FcA-CS to 7.21 m2·g-1, one-third of ferrocene-free DX-CS (21.71 m2·g-1), while enhancing thermal stability and PO43- adsorption performance. Adsorption kinetics and isotherm studies demonstrated that the interaction between DX-FcA-CS and PO43- followed a pseudo-second-order kinetic model and Langmuir model, indicating chemical and monolayered adsorption mechanisms, respectively. Moreover, DX-FcA-CS exhibited excellent anti-interference properties against concentrated co-existing inorganic ions and humic acid, along with high recyclability. The maximum adsorption capacity reached 1285.35 mg·g-1 (∼428.45 mg P g-1), three times that of DX-CS and surpassing many other adsorbents. PO43--loaded DX-FcA-CS could be further carbonized into electrode material due to its rich content of phosphorus and nitrogen, transforming waste into a valuable resource. These outstanding characteristics position DX-FcA-CS as a promising alternative for phosphate capture and recycling. Overall, this study presents a viable approach to designing environmentally friendly, recyclable, and cost-effective biomaterial for wastewater phosphate removal and value-added applications.
Highly Selective Capture of Phosphate Ions from Water by a Water Stable Metal-Organic Framework Modified with Polyethyleneimine

Hui Qiu,Luyang Yang,Fengling Liu,Yunxia Zhao,LeLe Liu,Jinhong Zhu,Mingxia Song

DOI: https://doi.org/10.1007/s11356-017-9946-9

2017-01-01

Environmental Science and Pollution Research International

Abstract:In this work, a series of polyethyleneimine (PEI) impregnated metal-organic framework (UiO-66) with varying PEI loadings were prepared and applied as sorbents to capture phosphate ions from water. As indicated by SEM and XRD analysis, PEI was dispersed on the outer surface and the inner pores of UiO-66. At 9.45% PEI loadings (UiO-66-3), the saturated adsorption capacity of phosphate reached 73.15 mg P/g at 298 K, which is superior to most sorbents ever reported. UiO-66-3 could sequestrate phosphate over a wide pH range from 2.0 to 7.0 with high efficiency. The sorption toward phosphate reached equilibrium in 50 min. Unlike commercial anion exchanger IRA-900, UiO-66-3 still exhibited high removal toward phosphate even large amount of coexisted anions were present. Successive sorption assay demonstrated that the removal efficiency of UiO-66-3 toward phosphate remained constant after six cyclic runs. All the above results indicated the great potential of UiO-66-3 as a promising sorbent for the decontamination of water from phosphate.
Regenerable neodymium-doped zirconium-based MOF adsorbents for the effective removal of phosphate from water

Guoting Luo,Zhuangzhuang Bi,Chali Liu,Zhaoneng Wan,Zhihong Chen,Muhan Chen,Zhangjie Huang

DOI: https://doi.org/10.1016/j.jece.2022.108610

IF: 7.7

2022-12-01

Journal of Environmental Chemical Engineering

Abstract:UiO-66-NH2 has been widely to remove phosphate from natural water, albeit having poor selectivity and low removal efficiency. Researchers are seeking to enhance the adsorption properties of this Metal-Organic Framework (MOF) and improve its practicability. In this study, the rare earth neodymium (Nd) was doped into UiO-66-NH2 to prepare NdUiO-X (X: mole ratio of Zr/Nd), which was used as an adsorbent to remove phosphate from water. The main adsorption parameters, such as pH value, equilibrium time, and initial concentration were investigated. Furthermore, the adsorption mechanism of NdUiO-0.5 was investigated via spectroscopic analysis (FTIR and XPS) and theoretical calculations (DFT and LOBA). The results showed that when the molar ratio of Nd/Zr was 0.50, the adsorption effect was at its maximum, with the calculated saturation adsorption capacity from the Langmuir model being 106.39 mg P/g. The NdUiO-0.5 adsorbent shows high stability in solutions with pH ranging from 3 to 9. This MOF was applied to the actual water sample to observe its phosphate adsorption capacity. When the dosage of NdUiO-0.5 was 0.15 g/L, the total phosphorus concentration of the actual water sample decreased from 0.57 mg P/L to 0.018 mg P/L. Mechanistic studies have shown that ligand exchange is the key mechanism of action behind phosphate removal via NdUiO-0.5. Besides, unconventional hydrogen bonds also play a very important role. Thus, the prepared NdUiO-0.5 is a high-efficient adsorbent for phosphate removal bearing potential applications in real-life scenarios.

engineering, chemical, environmental
Sodium Alginate/UiO-66-NH2 Nanocomposite for Phosphate Removal

Xiaohang Lin,Yuzhu Xiong,Fuping Dong

DOI: https://doi.org/10.3390/nano14141176

2024-07-10

Abstract:Environmental pollution of phosphorus is becoming increasingly concerning, and phosphate removal from water has become an important issue for controlling eutrophication. Modified metal-organic framework (MOF) materials, such as UiO-66-NH2, are promising adsorbents for phosphate removal in aquatic environments due to their high specific surface area, high porosity, and open active metal sites. In this study, a millimeter-sized alginate/UiO-66-NH2 composite hydrogel modified by polyethyleneimine (UiO-66-NH2/SA@PEI) was prepared. The entrapping of UiO-66-NH2 in the alginate microspheres and its modification with PEI facilitate easy separation in addition to enhanced adsorption properties. The materials were characterized by SEM, FTIR, XRD, and BET. Static, dynamic, and cyclic adsorption experiments were conducted under different pH, temperature, adsorbent dosage, and initial concentration conditions to assess the phosphate adsorption ability of UiO-66-NH2/SA@PEI. Under optimal conditions of 65 °C and pH = 2, 0.05 g UiO-66-NH2/SA@PEI adsorbed 68.75 mg/g, and the adsorption rate remained at 99% after five cycles of UiO-66-NH2/SA@PEI. These results suggest that UiO-66-NH2/SA@PEI composite materials can be used as an effective adsorbent for phosphate removal from wastewater.
Development of polymer-based nanosized hydrated ferric oxides (HFOs) for enhanced phosphate removal from waste effluents.

Bingjun Pan,Jun Wu,Bingcai Pan,Lu Lv,Weiming Zhang,Lili Xiao,Xiaoshu Wang,Xiancong Tao,Shourong Zheng

DOI: https://doi.org/10.1016/j.watres.2009.06.055

IF: 12.8

2009-01-01

Water Research

Abstract:Phosphate originated from industrial effluents is one of the key factors responsible for eutrophication of the receiving waterways especially in the developing countries such as China. In the current study we proposed a novel process to immobilize nanoparticulate hydrated ferric oxide (HFO) within a macroporous anion exchange resin D-201, and obtained a hybrid adsorbent (HFO-201) for enhanced phosphate removal from aqueous system. The resulting HFO-201 possesses two types of adsorption sites for phosphate removal, the ammonium groups bound to the D-201 matrix and the loaded HFO nanoparticles. The coexisting sulfate anion strongly competes for ammonium groups, which bind phosphate through electrostatic interaction. However, it does not pose any noticeable effect on phosphate adsorption by the loaded HFO nanoparticles, which is driven by the formation of the inner-sphere complexes. Batch adsorption experiments also indicated that HFO-201 exhibits a little higher capacity for phosphate than the commercially available phosphate-specific adsorbent ArsenXnp, which possesses similar structure of HFO-201 and is produced by another patented technique. Fixed-bed column tests indicate that phosphate retention by HFO-201 from the synthetic waters results in the significant decrease of P from 2mg/L to less than 0.01mg/L, with the treatment capacity of ∼700 bed volume (BV) per run, while that for D-201 was less than 200 BV under otherwise identical conditions. Such satisfactory performance of the hybrid adsorbent is mainly attributed to the specific affinity of HFO toward phosphate as well as the Donnan membrane effect exerted by the anion exchanger support D-201. Moreover, the exhausted HFO-201 was amenable to efficient in situ regeneration with a binary NaOH–NaCl solution for repeated use without any significant capacity loss. Similar satisfactory results were also observed by using a phosphate-containing industrial effluent as the feeding solution.
Defective UiO-66 for the highly efficient elimination of U(V) from wastewater: Insights to the effects of defects and pore structure on the adsorption process

Mingxin Zheng,Keng Xuan,Shuai Yan,Yaoping Guo,Yaxiong Huang,Runling Xu,Kaixuan Zhao,Zebing Li,Xun Li,Hao Jiang,Yadan Guo

DOI: https://doi.org/10.1016/j.seppur.2024.126550

IF: 8.6

2024-02-08

Separation and Purification Technology

Abstract:A defective metal–organic framework UiO-66–18 synthesized via a facile solvothermal synthesis method with trifluoroacetic acid as modulator was demonstrated to be highly efficient for the elimination of uranium from wastewater. The maximum adsorption capacity of UiO-66–18 toward uranium reached 622.75 mg g −1 , which was approximately 1.43 times higher than that of pristine UiO-66–0 prepared without TFA modulation. The superior elimination performance of UiO-66–18 was because the TFA modulation induced the generation of more missing-linker defects that endowed UiO-66–18 with hierarchical structure and more adsorption active sites for U(VI) capture. Further adsorption mechanism studies indicated that the elimination of U(VI) was endothermic monolayer chemisorption dominated by mass transfer-decomplexation-adsorption process. In addition, the effects of common ions on the elimination efficiency as well as the reusability of UiO-66–0 and UiO-66–18 were studied. This work provides a promising strategy and a theoretical basis for the design and preparation of efficient uranium adsorbent from the points of defects engineering and pore structure design.

engineering, chemical

Fabrication of agricultural waste supported UiO-66 nanoparticles with high utilization in phosphate removal from water

Fabrication of a Biomass-Based Hydrous Zirconium Oxide Nanocomposite for Preferable Phosphate Removal and Recovery

Fabrication and evaluation of a regenerable HFO-doped agricultural waste for enhanced adsorption affinity towards phosphate

The Novel Performance and Adsorption Mechanism of Synthesized Modified Zirconium-Based Metal-Organic Frameworks for Resource Recovery from Wastewater

Filter fabrication by constructing metal-organic frameworks membrane on waste maize straw for efficient phosphate removal from wastewater

Dynamics and Treatability of Heavy Metals in Pig Farm Effluent Wastewater by Using UiO-66 and UiO-66-NH2 Nanomaterials as Adsorbents

Size Modulation of Zirconium-Based Metal Organic Frameworks for Highly Efficient Phosphate Remediation.

[Fabrication of a Biomass-Based Hydrous Zirconium Oxide Nanocomposite for Advanced Phosphate Removal].

Preferable Phosphate Sequestration by Nano-La(iii) (hydr)oxides Modified Wheat Straw with Excellent Properties in Regeneration

Integrated fabrication of CMC@UiO-66–NH 2 @PEI composite adsorbents for efficient batch and dynamic phosphate capture

Nano-Fe2O3/bentonite Complexes for Enhanced Phosphorus Removal from Industrial Wastewater

Multifunctional Fe3O4/TiO2/NH2-UiO-66 with integrated interfacial features for favorable phosphate adsorption

Fabrication of amorphous metal-organic framework in deep eutectic solvent for boosted organophosphorus pesticide adsorption

Enhanced low-concentration phosphate adsorption using magnetic UiO-66@Fe3O4 composite with potential linker exchange

Yttrium-doped MOFs for efficient phosphate adsorption: Electrochemical properties, electro-assisted desorption, and mechanism study

Utilization and value-adding of waste: Fabrication of porous material from chitosan for phosphate capture and energy storage

Highly Selective Capture of Phosphate Ions from Water by a Water Stable Metal-Organic Framework Modified with Polyethyleneimine

Regenerable neodymium-doped zirconium-based MOF adsorbents for the effective removal of phosphate from water

Sodium Alginate/UiO-66-NH2 Nanocomposite for Phosphate Removal

Development of polymer-based nanosized hydrated ferric oxides (HFOs) for enhanced phosphate removal from waste effluents.

Defective UiO-66 for the highly efficient elimination of U(V) from wastewater: Insights to the effects of defects and pore structure on the adsorption process