Abstract:Reversible exchange of lithium from lithium cobaltite (LCO) with the layered rock-salt structure was first reported by Goodenough in 1980 [1]. It has since become a critical component in the cathode of lithium-ion batteries that power portable electronics like cell phones, laptop computers, and cordless power tools. The rate of lithium diffusivity in LCO particles ranges from 10 -7 to 10 -11 cm2/s depending upon the state of charge and the method of measurement [2]. Lithium diffusivity in LCO because of its layered structure is also dependent upon crystallographic direction. In thin-film, micro-batteries (TFMB’s), the crystallographic orientation of LCO is controlled through choice of conditions for deposition and crystallization [3]. The diffusivity of lithium is significantly greater within rather than across the basal plane [4]. Orientations of (104) and (110) are preferred for rate performance. Continuous, roll-to-roll sintering of LCO ribbon with thicknesses down to 10 μm was recently demonstrated [5]. The LCO ribbon because it is sintered and self-supporting can in principle serve as a mechanical support to reduce the proportions of inactive battery components to dramatically increase energy density. A possible way of creating a solid-state battery with LCO ribbon is to capitalize on the LiPON solid electrolyte from TFMB’s. Both composite and dense cathodes can be envisioned. Energy densities greater than 1500 Wh/L are possible. The practicality and design of a cathode-supported battery depends upon lithium diffusion in the LCO and charge transfer resistance at the interface with the separator. Ideally, transport is sufficiently facile that acceptable rate performance in a battery is realized with cathode thickness of greater than 20 μm. In this work, we report on characterization of lithium diffusivity and ohmic losses in sintered LCO with controlled grain textures. LCO cathodes with thicknesses of 15-30 μm with random and (003) grain textures were prepared by tape casting and rapid sintering. The (hk0) texture was made by taking advantage of the (003) textured green tape; approximately 200 layers were stacked and cold-welded to form a block with a thickness of ~8 mm. The sintered block was diced to expose the edge with the favorable (hk0) orientation. Electron backscatter diffraction maps and pole figures that illustrate the grain structure and texture are shown in Fig. 1. The texture is so strong that material is orthotropic in character. Lithium diffusivity and ohmic cell resistances were determined as a function of state of charge by galvanostatic intermittent titration [7]. An average diffusivity to use as a single figure of merit was also determined by fitting of capacities measured as a function of rate of discharge from a cut-off potential of 4.3 V. Rates of lithium diffusion in sintered LCO cathodes with the (hk0) texture is 0.09 μm2/s and approximately twelve-fold greater than for the (003) texture, 0.0076 μm2/s. Ohmic loss was also found to depend upon grain texture. It was approximately 60-100 Ωcm2 for (hk0) texture and >500 Ωcm2 for (003). A reasonable explanation for the elevated resistance is that charge transfer occurs more easily with the (hk0) texture. [1] K. Mizushima, P.C. Jones, P.J. Wiseman, and J.B. Goodenough, Mat. Res. Bull. , 15 (1980) 783-789, https://doi.org/10.1016/0025-5408(80)90012-4. [2] K. Dokko, M. Mohamedi, Y. Fujita, T. Itoh, M. Nishizawa, M. Umeda, and I. Uchida, J. Electrochem. Soc. , 148 (2001) A422-A426, https://doi.org/10.1149/1.1359197. [3] J. Trask, A. Anapolsky, B. Cardozo, E. Januar, K. Kumar, M. Miller, R. Brown, and R. Bhardwaj, J. Power Sources , 350 (2017) 56-64, https://dx.doi.org/10.1016/j.jpowsour.2017.03.017. [4] J. Xie, N. Imanishi, T. Matsumura, A. Hirano, Y. Takeda, and O. Yamamoto, Solid State Ionics , 179 2008) 362-370, https://doi.org/10.1016/j.ssi.2008.02.051. [5] C. Tanner and J. Lorenzo, ECS Meet. Abstr. MA2022-02 (2022) 2482, https://doi.org/10.1149/MA2022-0272482mtgabs. [6]J.B. Bates, N.J. Dudney, G.R. Gruzalski, R.A. Zuhr, A. Choudhury, C.F. Luck, and J.D. Robertson, Solid State Ionics , 53-56 (1992) 647-654, https://doi.org/10.1016/0167-2738(92)90442-R. [7] C.J. Wen, B.A. Boukamp, R.A. Huggins, and W. Weppner, J. Electrochem. Soc. , 126 (1979) 2258-2266, https://doi.org/10.1149/1.2128939. Figure 1

Thin Film Ruo2 Lithiation: Fast Lithium-Ion Diffusion Along The Interface

In Situ Atomic-Scale Imaging of Electrochemical Lithiation in Silicon.

Interfacial Lithiation Induced Leapfrog Phase Transformation in Carbon Coated Se Cathode Observed by In-Situ TEM

Stress-Controlled Three-Dimensional Phase Evolution in Lithium Iron Phosphate

Clearing surficial charge-transport obstacles to boost the performance of lithium-rich layered oxides

Atomic Resolution Observation of Conversion-Type Anode Ruo2 During the First Electrochemical Lithiation

(Invited) Lithium Battery Interfacial Engineering with Thin Conformal Polymer Coatings

Control of Lattice Orientation and Interface of LiCoO2 for All Solid State Batteries

Lithium Conversion in Metal-Metal Oxide Multilayer Nano-Architectures

Lithium Transport of Fast Battery Cycles in a LiMn2O4 Cathode Imaged by Operando Eels

Morphological Evolution of Multilayer Ni/NiO Thin Film Electrodes During Lithiation

In Situ Observation of Single‐Phase Lithium Intercalation in Sub‐25‐nm Nanoparticles

Dynamic surface phases controlling asymmetry of high-rate lithiation and delithiation in phase-separating electrodes

Lithium transport through Lithium-ion battery cathode coatings

(Invited) Grain Texture and Transport in Sintered Lithium Cobaltite

Fast Charge Transfer between LLZO Solid Electrolyte and LCO Cathode Thin Films with a Modified Interface

Interface Engineering Enabling Thin Lithium Metal Electrodes Down to 0.78 Μm for Garnet-Type Solid-State Batteries

Two-dimensional lithium diffusion behavior and probable hybrid phase transformation kinetics in olivine lithium iron phosphate

Theoretical Modeling of Protective Cathode Coatings and Cathode/Coating Interfaces in Li-Ion Batteries

Dimensionally Controlled Lithiation of Chromium Oxide

Ultrathin [110]‐confined Li4Ti5O12 Nanoflakes for High Rate Lithium Storage