Abstract:Solar radiation is captured by photovoltaic (PV) panels, which use it to create electricity. However, an overabundance of photons striking the PV's surface raises its temperature, which lowers its efficiency. These days, cooling solar panels is very important, and research on these methods is widely available in the literature. Thus, the study field's problems truly lie in developing new or improved methods for doing the same tasks. The goal of this work is to further boost the efficiency of photovoltaic (PV) panels beyond what can be achieved with PCM and free/forced convection alone. To do this, phase change materials (PCM) are cooled using both free and forced convection. In accordance with the latitude of Lebanon's Bekaa Valley, four cooling techniques are experimentally investigated. A photovoltaic panel using phase-change material (PCM) with copper and aluminum wires in a 70 %–20 %–10 % mass ratio (CPCM-PV), respectively, is the first cooling method. In the second approach, four 5 cm long fins are fixed under free convection using the same combination of aluminum fins inside the PCM container while preserving the same ratio (IEF-PCM-Free-PV). The third technique is the same as the second but with forced convection (IEF-PCM-Forced-PV), while the fourth technique uses an aluminum finned plate with 16 finned plates under forced convection (F-Forced-PV). IEF-PCM-Forced-PV showed the most relative increases in efficiency rate of energy dissipated of 20.36 % and 62.24 %, respectively, as compared to the regular PV panel, according to the results. F-Forced-PV, IEF-PCM-Free-PV, and CPCM-PV showed an increase in relative efficiency of 16.87 %, 6.3 %, and 3.9 % respectively, and correspondingly, these enhancements were accompanied by an increase in energy dissipation of 55.80 %, 44.85 %, and 41.18 % for each system. Economically, the IEF-PCM-Forced-PV had the highest total yearly savings of $17.87 with a payback period of 1.9 years. An appropriate transient energy balance is conducted and permitted to demonstrate clearly the transient behavior of the system under the various cooling techniques. Finally, the percentage of enhancement using the newly suggested composite PCM with internal and external fins under forced convection is compared to the enhancement found in the literature for various classical techniques and shows greater potential for further enhancement of the PV performance.

Thermal Management of Conventional Photovoltaic Module Using Phase Change Materials—an Experimental Investigation

Thermal management of solar photovoltaic module by using drilled cylindrical rods integrated with phase change materials

Maximizing the Energy Output of a Photovoltaic–thermal Solar Collector Incorporating Phase Change Materials

Experimental Investigation on Effects of Thermal Resistances on a Photovoltaic-Thermoelectric System Integrated with Phase Change Materials

Experimental Study and Performance Analysis on Solar Photovoltaic Panel Integrated with Phase Change Material

Thermal analysis of solar panel with phase change material: experimental and numerical study

Thermal management of photovoltaic panel by honeycomb-like metal structure filled with phase change material

A Parametric Study about the Potential to Integrate Phase Change Material into Photovoltaic Panel

Efficiency enhancement of photovoltaic module using bio-based eutectic phase change material: An experimental study

Influence of Different Melting Points of Phase Change Material on Photovoltaic Phase Change Materials System Performance: An Energy, Exergy, and Environmental Point of View

Research Progress of Photovoltaic Cooling Systems Based on Phase Change Materials: An Overview

Experimental Study of Photovoltaic Heat Pump System Based on Modular Phase Change Material

Electrical and thermal performance assessment of photovoltaic thermal system integrated with organic phase change material

Thermal evaluation of photovoltaic panels combined pulsating heat pipe with phase change materials: numerical study and experimental validation

Experimental, numerical, and 4E assessment of photovoltaic module using macro-encapsulation of pure and nano phase change material: A comparative analysis

Numerical Study on 2-Stage Phase Change Heat Sink for Cooling of Photovoltaic Panel

Investigation on Designed Fins-Enhanced Phase Change Materials System for Thermal Management of a Novel Building Integrated Concentrating PV

Experimental Study on Optimizing Photovoltaic Panel Efficiency: Harnessing Paraffin Wax Phase Change for Temperature Reduction

A comprehensive experimental study of cooling photovoltaic panels using phase change materials under free and forced convection – Experiments and transient analysis

Annual Thermal Management of the Photovoltaic Module to Enhance Electrical Power and Efficiency Using Heat Batteries

Performance study of a new photovoltaic thermoelectric utilization system based on spectral beam splitting device