Mesoporous TiN Microspheres As an Efficient Polysulfide Barrier for Lithium–sulfur Batteries

Bin Qi,Xiaosen Zhao,Shaogang Wang,Ke Chen,Yingjin Wei,Gang Chen,Yu Gao,Dong Zhang,Zhenhua Sun,Feng Li

DOI: https://doi.org/10.1039/c8ta04920c

IF: 11.9

2018-01-01

Journal of Materials Chemistry A

Abstract:A separator modified with mesoporous titanium nitride (MTN) microspheres acting as a highly effective polysulfide blocking layer for Li–S batteries.

What problem does this paper attempt to address?

Effective Dual Polysulfide Rejection by a Tannic Acid/Fe-III Complex-Coated Separator in Lithium-Sulfur Batteries

Hong Zhang,Chuner Lin,Xuanhe Hu,Baoku Zhu,Dingshan Yu

DOI: https://doi.org/10.1021/acsami.8b01189

IF: 9.5

2018-01-01

ACS Applied Materials & Interfaces

Abstract:The solubility behaviour of polysulfides in electrolyte solutions is a major bottleneck prior to the practical application of the lithium-sulfur battery. To address this issue, we fabricate a tannic acid/FeIII complex-coated polypropylene (PP) separator (TA/FeIII-PP separator) via a simple, fast, and green method. Benefiting from dual-confinement effects based on Lewis acid-base interactions between FeIII and polysulfides as well as the dipole-dipole interactions between rich phenol groups and polysulfides, the migration of polysulfides is effectively suppressed. Meanwhile, the porous structure of the PP separator is not destroyed by an additional coating layer. Thus, the TA/FeIII-PP separator can retain rapid lithium ion transport, eventually leading to a significant improvement in both the discharge capacity and rate performance of the corresponding lithium-sulfur cells. The cell with the TA/FeIII-PP separator presents a low capacity fade of 0.06% per cycle over 1000 cycles at 2.0 C, along with a high Coulombic efficiency of >97% over 300 cycles at 0.5 C. With respect to the one with the bare PP separator, the cell with the TA/FeIII-PP separator exhibits a 1.7-fold increase in the discharge capacity at 3.0 C. The proposed simple and economical approach shows great potential in constructing advanced separators to retard the shuttle effect of polysulfides for lithium-sulfur batteries.
TiO2@Porous carbon nanotubes modified separator as polysulfide barrier for lithium-sulfur batteries

Zhengyuan Gao,Zhiyang Xue,Yingchun Miao,Bin Chen,Jinshan Xu,Hongqi Shi,Tao Tang,Xiangyu Zhao

DOI: https://doi.org/10.1016/j.jallcom.2022.164249

IF: 6.2

2022-06-01

Journal of Alloys and Compounds

Abstract:The severe shuttle effect of polysulfides in lithium-sulfur (Li-S) batteries leads to rapid performance deterioration. Herein, a functional separator composed of TiO2@surface-modified carbon nanotubes composite on polypropylene (PP) separator (donated as TiO2@SCNT/PP) is developed toward the effective blocking of polysulfide shuttle. The as-assembled Li-S batteries using this functional separator with the strongly polar TiO2 and highly conductive CNTs demonstrated considerably enhanced reversible capacity, cycling performance and reaction kinetics. The corresponding simple sulfur cathode with 70 wt% elemental sulfur powders exhibits a high initial discharge capacity of 1103.9 mAh g−1, a high capacity of 848.0 mAh g−1 after 200 cycles at 0.5 C, and a capacity decay of only 0.066% per cycle over 900 cycles. Moreover, a high reversible capacity of 746.5 mAh g−1 is maintained after 300 cycles at 1 C. In contrast, the low reversible capacity of 218.5 mAh g−1 at 0.5 C is obtained without the use of the TiO2@SCNT/PP.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
2D Ultrathin Titanium Nitride Nanosheets as Separator Coatings for Li-S Batteries

Shan Lu,Lucheng Cai,Jiaqian Wang,Hangjun Ying,Zhongkang Han,Weiqiang Han,Zongping Chen

DOI: https://doi.org/10.1002/smll.202307784

IF: 13.3

Small

Abstract:Transition metal nitrides (TMNs) are affirmed to be an appealing candidate for boosting the performance of lithium-sulfur (Li-S) batteries due to their excellent conductivity, strong interaction with sulfur species, and the effective catalytic ability for conversion of polysulfides. However, the traditional bulk TMNs are difficult to achieve large active surface area and fast transport channels for electrons/ions simultaneously. Here, a 2D ultrathin geometry of titanium nitride (TiN) is realized by a facile topochemical conversion strategy, which can not only serve as an interconnected conductive platform but also expose abundant catalytic active sites. The ultrathin TiN nanosheets are coated on a commercial separator, serving as a multifunctional interlayer in Li-S batteries for hindering the polysulfide shuttle effect by strong capture and fast conversion of polysulfides, achieving a high initial capacity of 1357 mAh g-1 at 0.1 C and demonstrating a low capacity decay of only 0.046% per cycle over 1000 cycles at 1 C.
Immobilizing Polysulfides with MXene-Functionalized Separators for Stable Lithium-Sulfur Batteries

Jianjun Song,Dawei Su,Xiuqiang Xie,Xin Guo,Weizhai Bao,Guangjie Shao,Guoxiu Wang

DOI: https://doi.org/10.1021/acsami.6b09027

2016-11-02

Abstract:Lithium-sulfur batteries have attracted increasing attention as one of the most promising candidates for next-generation energy storage systems. However, the poor cycling performance and the low utilization of sulfur greatly hinder its practical applications. Here we report the improved performance of lithium-sulfur batteries by coating Ti3C2Tx MXene nanosheets (where T stands for the surface termination, such as -O, -OH, and/or -F) on commercial "Celgard" membrane. In favor of the ultrathin two-dimensional structure, the Ti3C2Tx MXene can form a uniform coating layer with a minimum mass loading of 0.1 mg cm-2 and a thickness of only 522 nm. Owing to the improved electric conductivity and the effective trapping of polysulfides, the lithium-sulfur batteries with MXene-functionalized separators exhibit superior performance including high specific capacities and cycling stability.
Titanium-Containing Metal–Organic Framework Modified Separator for Advanced Lithium–Sulfur Batteries

Chu Qi,Lin Xu,Jia Wang,Huilan Li,Chengcheng Zhao,Lina Wang,Tianxi Liu

DOI: https://doi.org/10.1021/acssuschemeng.0c03536

2020-08-04

Abstract:The shuttling of polysulfide intermediates (Li2Sn, 2 < n ≤ 8) and the dendrite growth on the Li-metal surface have blocked the practical applications of lithium–sulfur (Li–S) batteries. Functionalizing the separator provides a straightforward approach to address these issues. Herein, we demonstrate a multifunctional MIL-125(Ti)-modified polypropylene/polyethylene separator for advanced Li–S batteries. The MIL-125(Ti), a Ti-containing metal–organic framework (MOF), features an open-skeleton construction, a high intrinsic microporosity and a Lewis acid characteristic. Compared with pristine separator, that with MIL-125(Ti) coating shows better electrolyte wettability and less resistance. The unique coating layer acts as an effective physical and chemical barrier region to capture polysulfide species without affecting the smooth transport of Li+. Meanwhile, the highly ordered micropores with a diameter of ∼1.5 nm in the MOFs guide in a homogeneous Li+ plating and thereby inhibit lithium dendrites. Consequently, the MOF-modified separator enables a significantly improved cycling stability and rate capability of the Li–S battery. The capacity retention of over 60% at 0.2 C (1 C = 1675 mA g–1) upon 200 cycles and a specific capacity of 612 mAh g–1 at 2 C is realized. The facile approach offers an effective pathway toward high-performance Li–S batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acssuschemeng.0c03536?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acssuschemeng.0c03536</a>.Porosity measurement, calculated adsorption energy between polysulfides and MIL-125(Ti), polysulfide adsorption experiment, Ti 2p XPS spectrum of MIL-125(Ti), mechanical properties of separators, characterization of the separator after stretching, rate capability of Li–S cells, cyclic performance of Li–S cells at 0.2 C, comparison of different MOF-modified separators for Li–S batteries, morphology of bare Li anode, and performance of Li||Cu and Li||Li symmetric cells (<a class="ext-link" href="/doi/suppl/10.1021/acssuschemeng.0c03536/suppl_file/sc0c03536_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

chemistry, multidisciplinary,engineering, chemical,green & sustainable science & technology
Partially oxidized Ti3–yNbyC2Tx MXene nanosheets as efficient sulfur hosts and separator modification for Li–S batteries

Qiang Wang,Bin Deng,Xiao Zhang,Linyu Cao,Kewen Wang,Wei Yao,Chi Chen,Hang Zhao,Jianguang Xu

DOI: https://doi.org/10.1016/j.jmat.2024.07.005

IF: 8.589

2024-01-01

Journal of Materiomics

Abstract:MXenes hold significant potential in lithium-sulfur (Li–S) battery applications due to its robust polysulfide adsorption and catalytic effect on polysulfide transformation achieved by adjustable transition metals and surface functional groups. Introduction of heteroatoms can prompt an electron distribution and refine MXenes surface structure, thereby substantially enhancing its electrochemical capabilities. Herein, partially oxidized Ti3–yNbyC2Tx (O-Ti3–yNbyC2Tx) heterostructure has been prepared by in-situ oxidization of Ti3–yNbyC2Tx MXene in anhydrous ethanol. The incorporation of niobium (Nb) species within the Ti3C2Tx matrix plays a pivotal role: augmenting the catalytic conversion of polysulfides and concurrently fortifying the cyclic stability of the electrode constituents. When employed in Li–S batteries separator and cathode, it delivers impressive rate performance and durability. The O-Ti2.7Nb0.3C2Tx/S cathode exhibits an initial discharge capacity of 1260 mA·h/g at a current density of 0.1 C, and a minuscule capacity decay rate of a mere 0.029% per cycle over 2000 cycles at 1 C. Even at a significantly elevated current density of 4 C, an appreciable capacity of 640 mA·h/g is sustained. This research opens new avenues to explore MXene heterostructures with both superior electrocatalytic and adsorption properties for alkali metal-S batteries.
Tg-C 3 N 4 -coated functional separator as polysulfide barrier of high-performance lithium-sulfur batteries

Xin Liu,Heng Ma,Chenchen Hu,Ning Liu,Yan Zhao

DOI: https://doi.org/10.1088/1361-6528/ac1cbc

IF: 3.5

2021-09-02

Nanotechnology

Abstract:Lithium sulfur (Li-S) battery is considered as a promising alternative for the development of battery technologies. However, the shuttle effect seriously limits its practical use. Herein, hollow tubular graphene-like carbon nitride (Tg-C3N4) is synthesized and utilized as a functional interlayer to inhibit shuttling effect and promote catalytic kinetics. Both experiments and DFT calculations together suggest that N-doping enhances the electron transfers between Tg-C3N4 and LiPSs, leading to improved chemical adsorptions and catalytic effects towards the redox conversions of the active sulfur species. Besides, Tg-C3N4 delivers a unique hollow tubular architecture with massive ion transfer pathways and fully exposed active interfaces. In addition, the abundant C–N heteroatomic structures also impose strong chemical immobilization toward lithium polysulfides. Benefiting from these unique superiorities, the cell with the Tg-C3N4-modified separator exhibits a reversible capacity of 494 mAh g−1 after 500 cycles at 1 C with a negligible capacity decay of 0.085% per cycle, indicating an efficient strategy toward high-performance modified separators.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
Metallically conductive TiB2 as a multi-functional separator modifier for improved lithium sulfur batteries

Liming Jin,Jie Ni,Chao Shen,Fenglai Peng,Qiang Wu,Donghao Ye,Junsheng Zheng,Gaoran Li,Cunman Zhang,Zhoupeng Li,Jim P. Zheng

DOI: https://doi.org/10.1016/j.jpowsour.2019.227336

IF: 9.2

2020-01-01

Journal of Power Sources

Abstract:A metallically conductive TiB2 is developed to construct multifunctional separator toward improved lithium-sulfur (Li–S) battery performance. Coupled with two-dimensional graphene, the obtained TiB2@G separator fulfills a synergistic combination of strong physical and chemical sulfur immobilization as well as a high-efficiency sulfur reutilization, thus establishing a robust barrier against the polysulfide shuttling and enabling a fast and durable sulfur electrochemistry. As a result, cells based on TiB2@G separator exhibit a high sulfur utilization with 1350 mA h g−1 capacity at 0.05C, superb rate capability up to 5.0C, and excellent cyclability with a high capacity retention over 85% after 300 cycles at 0.5C. Moreover, significantly mitigated self-discharge and considerably high areal capacity of 5.8 mA h cm−2 can be also achieved, indicating the great promise of this separator design for the development of high-performance Li–S batteries.
Synthesis of Titanium Molybdenum Nitride-Decorated Electrospun Carbon Nanofiber Membranes as Interlayers to Suppress Polysulfide Shuttling in Lithium–Sulfur Batteries

Ying Zhu,Xiaodong Wu,Miaoran Li,Yuanxiao Ji,Qi Li,Xuexia He,Zhibin Lei,Zonghuai Liu,Ruibin Jiang,Jie Sun

DOI: https://doi.org/10.1021/acssuschemeng.1c05959

2022-01-05

Abstract:The practical application of lithium–sulfur (Li–S) batteries is seriously restricted by the “shuttle effect” of polysulfide ions. The design of functional interlayers is one of the effective solutions to overcome this defect. In this work, titanium molybdenum nitride (TMN) solid solution nanoparticles have been successfully decorated on electrospun carbon nanofibers (CNFs) to form a continuous flexible TMN@CNF membrane through a one-step calcination process under NH3 atmosphere. By regulating the mass ratio of titanium acetylacetonate TiO(acac)2 and molybdenum acetylacetonate MoO2(acac)2, the dissolved amount of Mo into TiN can be precisely controlled. Through the visible adsorption test, cyclic voltammetry test of Li2S6-based symmetric cells, and potentiostatic discharge measurement, such a TMN@CNF membrane has been confirmed to exhibit excellent adsorption and catalytic capacity on lithium polysulfides. With the help of DFT calculations, the adsorption capacity of TMN phase is confirmed to be greatly enhanced when compared with that of TiN, which can be attributed to the improved overlap of the electronic state after the introduction of Mo to TiN. By using such a membrane as the interlayer in Li–S batteries, it can effectively increase the cell’s initial capacity to 1205 mA h g–1 at 0.5 C when the dissolved amount of Mo reaches 50%. At the current density of 2 C, the discharge capacity of the cell by using such a multifunctional interlayer can reach up to 947 mA h g–1 and remains at 390 mA h g–1 after 1000 cycles, corresponding to a 0.059% capacity decay per cycle. This work provides a feasible method to prepare a flexible interlayer with a regulated electronic fine structure and strong chemisorption and catalytic ability for the development of the high performance Li–S batteries.

chemistry, multidisciplinary,engineering, chemical,green & sustainable science & technology
A Ti3C2Tx-Based Composite as Separator Coating for Stable Li-S Batteries

Ruowei Yi,Yinchao Zhao,Chenguang Liu,Yi Sun,Chun Zhao,Yinqing Li,Li Yang,Cezhou Zhao

DOI: https://doi.org/10.3390/nano12213770

2022-01-01

Abstract:The nitrogen-doped MXene carbon nanosheet-nickel (N-M@CNi) powder was successfully prepared by a combined process of electrostatic attraction and annealing strategy, and then applied as the separator coating in lithium-sulfur batteries. The morphology and structure of the N-M@CNi were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), Raman spectrum, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption-desorption method. The strong LiPS adsorption ability and high conductivity are associated with the N-doped carbon nanosheet-Ni modified surface. The modified separator offers the cathode of Li-S cell with greater sulfur utilization, better high-rate adaptability, and more stable cycling performance compared with the pristine separator. At 0.2 C the cell with N-M@CNi separator delivers an initial capacity of 1309 mAh g(-1). More importantly, the N-M@CNi separator is able to handle a cathode with 3.18 mg cm(-2) sulfur loading, delivering a capacity decay rate of 0.043% with a high capacity retention of 95.8%. Therefore, this work may provide a feasible approach to separator modification materials towards improved Li-S cells with improved stability.
MXene‐Derived Ti n O 2 n− 1 Quantum Dots Distributed on Porous Carbon Nanosheets for Stable and Long‐Life Li–S Batteries: Enhanced Polysulfide Mediation via Defect Engineering

Heng Zhang,Li Yang,Peigen Zhang,Chengjie Lu,Dawei Sha,Bingzhen Yan,Wei He,Min Zhou,Wei Zhang,Long Pan,ZhengMing Sun

DOI: https://doi.org/10.1002/adma.202008447

IF: 29.4

2021-04-17

Advanced Materials

Abstract:The application of Li-S batteries has been hindered by the shuttling behavior and sluggish reaction kinetics of polysulfides. Here an effective polysulfide immobilizer and catalytic promoter is developed by proposing oxygen-vacancy-rich Tin O2 n -1 quantum dots (OV-Tn QDs) decorated on porous carbon nanosheets (PCN), which are modulated using Ti3 C2 Tx MXene as starting materials. The Tn QDs not only confine polysulfides through strong chemisorption but also promote polysulfide conversion via redox-active catalysis. The introduction of oxygen vacancies further boosts the immobilization and conversion of polysulfides by lowering the adsorption energy and shortening the bond lengths. The PCN provides a physical polysulfide confinement as well as a flexible substrate preventing OV-Tn QDs from aggregation. Moreover, the two building blocks are conductive, thereby effectively improving the electron/charge transfer. Finally, the ultrasmall size of QDs along with the porous structure endows OV-Tn QDs@PCN with large specific surface area and pore volume, affording adequate space for S loading and volume expansion. Therefore, the OV-Tn QDs@PCN/S delivers a high S loading (79.1 wt%), good rate capability (672 mA h g-1 at 2 C), and excellent long-term cyclability (88% capacity retention over 1000 cycles at 2 C). It also exhibits good Li+ storage under high S-mass loading and lean electrolyte.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Nitrogen‐Deficient Graphitic Carbon Nitride/Carbon Nanotube as Polysulfide Barrier of High‐Performance Lithium‐Sulfur Batteries

Heng Ma,Cailing Song,Ning Liu,Yan Zhao,Zhumabay Bakenov

DOI: https://doi.org/10.1002/celc.202001259

IF: 4

2020-11-19

ChemElectroChem

Abstract:Lithium‐sulfur (Li‐S) batteries have been attracting growing interest in the past few years due to their outstanding theoretical energy density, but the lower cycle performance and especially the migration of polysulfides significantly inhibited its applicability. Herein, we propose a novel strategy for trapping lithium polysulfides (LiPSs) by combining nitrogen‐deficient graphitic carbon nitride (g‐C 3 N 4‐x ) and carbon nanotubes (CNTs) to form a functional interlayer between the separator and sulfur cathode in Li‐S batteries. The defect chemistry present in g‐C 3 N 4‐x not only improves the chemical affinity toward polysulfides but also catalyzes the polysulfide reactions. Besides, the interwoven scaffold‐like CNT network in the g‐C 3 N 4‐x /CNT composite accelerates the process of electron transfer. Based on this synergistic effect, the cells with g‐C 3 N 4‐x /CNT‐modified separators showed a remarkable discharge capacity of 1128 mAh g ‐1 at 0.2 C, and a reversible capacity of 774 mAh g ‐1 after 100 cycles, indicating an efficient strategy toward high‐performance modified separators.

electrochemistry
Cobalt/MXene‐derived TiO2 heterostructure as a functional separator coating to trap polysulfide and accelerate redox kinetics for reliable lithium‐sulfur battery

Zhihua Chang,Wendong Liu,Junan Feng,Zenghui Lin,Chuan Shi,Tianyi Wang,Yaojie Lei,Xiaoxian Zhao,Jianjun Song,Guoxiu Wang

DOI: https://doi.org/10.1002/batt.202300516

2023-12-20

Batteries & Supercaps

Abstract:Lithium‐sulfur (Li‐S) batteries are one of the most potential new energy storage systems due to their high theoretical capacity and high energy density. However, the application of Li‐S batteries is currently restricted due to the dissolution of polysulfides in the electrolyte, which leads to the shuttle effect of lithium polysulfides (LiPSs). Here, we present a Co@MXene‐derived TiO2 heterostructure decorated on carbon sheets derived from folic acid (Co@M‐TiO2/C) as a functional separator coating to trap polysulfide and accelerate redox kinetics in Li‐S batteries. The interconnected porous structure with good electrical conductivity of the heterostructure boasts rapid ion diffusion and efficient electron transfer within the battery. By attaching Co and MXene‐derived dual‐phased TiO2 to two‐dimensional carbon sheets, heterostructures are formed, ensuring complete exposure of the active sites. These heterostructures exhibit catalytic effects on LiPSs and excellent adsorption capabilities, effectively inhibiting the shuttle effect and accelerating the redox kinetics. Considering these advantages, the Li‐S battery with the optimized Co@M‐TiO2/C modified separator demonstrates a high specific capacity of 1481.7 mAh g‐1 at 0.2 C, superior rate performance of 855.5 mAh g‐1 at 2 C, and excellent cycling performance under a high sulfur load of 4.4 mg cm‐2.

materials science, multidisciplinary,electrochemistry
MXene Derivative Ta4C3-Ta2O5 Heterostructure As Bi-Functional Barrier for Li-S Batteries

Qi Liang,Sizhe Wang,Xiaohua Jia,Jin Yang,Yong Li,Dan Shao,Lei Feng,Jiaxuan Liao,Haojie Song

DOI: https://doi.org/10.1016/j.jmst.2022.11.059

2023-01-01

Abstract:The shuttle effect of polysulfides during the charging and discharging of lithium-sulfur (Li-S) batteries and the growth of Li dendrites are crucial obstacles to hinder the commercialization of Li-S batteries. Heterostructure engineering is an effective strategy to accelerate catalytic conversion and suppress the dissolution of polysulfides. Herein, we report a Ta4C3-Ta2O5 heterostructure composite as a bi-functional modified separator that not only achieves effective protection for lithium metal but also accelerates the polysulfides redox kinetics process. This heterostructure possesses efficient chemical anchoring and abun-dant active sites to immobilize polysulfides by synergistic effect, which endows a stable long cycling per-formance for Li-S batteries. This corresponds to an initial high capacity of 801.9 mAh g -1 at 1 C with a decay rate of 0.086% for 500 cycles. Due to its high Young's modulus (up to 384 GPa), Ta4C3 contributes to forming a protective layer on the Li metal surface to inhibit the growth of Li dendrites. Accordingly, the symmetrical cell has a stable overpotential for 700 cycles at 20 mA cm-2/20 mAh cm-2. So, this "one stone two birds" design affords a novel perspective for high-energy Li-S battery storage system design and Li metal protection.(c) 2023 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.
Mesoporous Boron Carbon Nitride/graphene Modified Separators As Efficient Polysulfides Barrier for Highly Stable Lithium-Sulfur Batteries

Kai Sun,Pengqian Guo,Xiaonan Shang,Yujun Fu,Pu Cheng,Qiming Liu,Qunhong Weng,Dequan Liu,Deyan He

DOI: https://doi.org/10.1016/j.jelechem.2019.04.047

IF: 4.598

2019-01-01

Journal of Electroanalytical Chemistry

Abstract:Lithium‑sulfur batteries (LSBs) have drawn intense attention due to their high theoretical specific energy and low material cost. However, shuttle effect of the lithium polysulfides (LiPSs) dissolved in the electrolyte results in severe capacity fading and self-discharge. Herein, a multifunctional modifier composed of mesoporous boron carbon nitride and conductive graphene (BCN/G) has been developed to modify separator as an efficient barrier for LiPSs in LSBs. Benefiting from such a modified separator, LSBs exhibit improved cycling capacity and high rate capacities. The excellent electrochemical performances are mainly attributed to the strong chemical interactions between LiPSs and conductive BCN/G modifier, which have been confirmed by X-ray photoelectron spectroscopy analyses. Such a design of separator opens a new approach for high-performance LSBs.
Electrospun carbon nanofibers with MnS sulfiphilic sites as efficient polysulfide barriers for high-performance wide-temperature-range Li–S batteries

Xin Wang,Xiaosen Zhao,Chenhui Ma,Zhenzhen Yang,Gang Chen,Lei Wang,Huijuan Yue,Dong Zhang,Zhenhua Sun

DOI: https://doi.org/10.1039/c9ta12137d

IF: 11.9

2020-01-01

Journal of Materials Chemistry A

Abstract:Nanofibers with MnS sulfiphilic sites are introduced as flexible interlayers into Li–S batteries, reducing the shuttle effect and accelerating the reaction kinetics in wide work temperature range.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Design and Synthesis of Novel Pomegranate-Like TiN@MXene Microspheres As Efficient Sulfur Hosts for Advanced Lithium Sulfur Batteries

Mengjie Zhang,Yang Lu,Zhenjie Yue,Mengmeng Tang,Xiaoke Luo,Chen,Tao Peng,Xianming Liu,Yongsong Luo

DOI: https://doi.org/10.1039/d3ra00095h

IF: 4.036

2023-01-01

RSC Advances

Abstract:Lithium-sulfur (Li-S) batteries have the characteristics of low cost, environmental protection, and high theoretical energy density, and have broad application prospects in the new generation of electronic products. However, there are some problems that seriously hinder the Li-S batteries from going from the laboratory to the factory, such as poor stability caused by the large volume expansion of sulfur during charging and discharging, sluggish kinetics of the electrochemical reaction resulting from the low conductivity of the active materials, and loss of active materials arising from the dissolution and diffusion of the intermediate product lithium polysulfides (LiPSs). In this paper, the two-dimensional layered material MXene and TiN are firstly combined by spray drying method to prepare pomegranate-like TiN@MXene microspheres with both adsorption capacity and catalytic effect on LiPSs conversion. The interconnected skeleton composed of MXene not only solves the problem of easy stacking of MXene sheets but also ensures the uniform distribution of sulfur. Without affecting the excellent characteristics of MXene itself, the overall conductivity of the composite electrode material is improved. The TiN hollow nanospheres are coated with MXene layers to form a shell, catalyzing the adsorption of LiPSs and accelerating the transformation of high-order LiPSs to Li2S2/Li2S. As a result, the TiN@MXene cathode delivers a high initial discharge capacity of 1436 mA h g(-1) at 0.1C, excellent rate performance of 636 mA h g(-1) up to 3C, and an ultralong lifespan over 1000 cycles with a small capacity decay of 0.048% per cycle at the current density of 1.0C.
Ni/SiO2/Graphene-modified separator as a multifunctional polysulfide barrier for advanced lithium-sulfur batteries

Chao Chen,Qingbin Jiang,Huifang Xu,Yaping Zhang,Bingkai Zhang,Zhenyu Zhang,Zhan Lin,Shanqing Zhang

DOI: https://doi.org/10.1016/j.nanoen.2020.105033

IF: 17.6

2020-10-01

Nano Energy

Abstract:Lithium-sulfur batteries with high energy density and low cost are widely recognized as one of the most promising next generation energy storage devices. However, their practical applications are hampered by the notorious polysulfide shuttle effect, which leads to a series of problems including the loss of active materials and poor cycling efficiency. We herein develop a Ni nanoparticles embedded in silica (Ni/SiO2) nanosheet spheres, which are mixed with graphene, and then coated on the separator as a highly effective lithium polysulfides (LiPSs) blocking layer. The Ni/SiO2/Graphene-modified separator is able to anchor LiPSs through affinity towards LiPSs by silica and Ni atoms, and enable rapid conversion between LiPSs and Li2S2/Li2S by abundant Ni catalytic sites. The mesoporous hollow structure of the Ni/SiO2 nanosheet spheres also facilitates Li+ diffusion. As a result, Li–S batteries with the Ni/SiO2/Graphene-modified separator achieve a stable cycling performance (specific capacity of 922 mAh g−1 after 100 cycles, with the cyclic decay rate of 0.28%), coulombic efficiency of approximately 100%, and a high rate capability (782 mAh g−1 at 2 C). Our work provides an effective strategy to build a multifunctional separator for highly stable Li–S batteries.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
Multi‐functional TiO 2 Nanosheets/carbon Nanotubes Modified Separator Enhanced Cycling Performance for Lithium‐sulfur Batteries

Peng Chen,Zexi Wang,Bingyu Zhang,Jianxun Zhao,Heng Liu,Xin Guo,Wanqiang Liu,Zhongmin Su

DOI: https://doi.org/10.1002/er.5171

IF: 4.6

2020-01-01

International Journal of Energy Research

Abstract:TiO2 nanosheets (TiO(2)NSs) have been investigated for lithium-sulfur (Li-S) batteries as strategically designed TiO2 nanosheet/carbon nanotube (TiO2NS/CNT) composite modified polypropylene (PP) separator to inhibit the shuttling of the intermediate polysulfides. The modified separator was fabricated by the vacuum filtration method using the exfoliation TiO(2)NSs and untreated carbon nanotube (CNT) composites. The multi-functional TiO2NS/CNT coating not only reduced the electrochemical resistance but also localized the migrating polysulfides by the cooperative effect of physical adsorption and chemical binding. Specifically, the composition ratio of TiO(2)NSs/CNTs and the interface character have been studied. It was found that the optimum ratio and perfect electrolyte wettability of the TiO2NS/CNT layers were all the critical reasons to achieve good battery performance. The high initial discharge capacity of 1247 mA h g(-1) at 0.2 C rate, which was 75% of the theoretical capacity of sulfur, 98% average coulombic efficiency, and 627 mA h g(-1) discharge capacity retention after 100 cycles were obtained with the TiO2NS/CNT coating separator.
Modified separators boost polysulfides adsorption-catalysis in lithium-sulfur batteries from Ni@Co hetero-nanocrystals into CNT-porous carbon dual frameworks

Jing Xiong,Xinyun Liu,Peng Xia,Xincheng Guo,Shengjun Lu,Hua Lei,Yufei Zhang,Haosen Fan

DOI: https://doi.org/10.1016/j.jcis.2023.08.185

IF: 9.9

2023-09-02

Journal of Colloid and Interface Science

Abstract:In this manuscript, nickel/cobalt bimetallic nanocrystals confining into three-dimensional interpenetrating dual-carbon conductive structure (NiCo@C/CNTs) were successfully manufactured by annealing its core-shell structure (Ni-ZIF-67@ZIF-8) precursor under the high temperature. The results presented that the bimetallic nickel and cobalt nanocrystals with superior catalytic activity could quickly convert solid Li 2 S/Li 2 S 2 into soluble LiPSs and effectively decrease the energy barrier. While the hierarchical CNT-porous carbon dual frameworks can provide quick electron/ion transport because of their large specific surface area and the exposure of enough active sites. When used as the separator modifier for lithium sulfur batteries, the battery properties were significantly improved with high specific capacity, outstanding rate capability, and long-term cycle stability. Specifically, its initial specific capacity can achieve to 1038.51 mAh g −1 at 0.5C. At the high rate of 3C, it still delivers satisfactory discharge capacity of 555 mAhg −1 and the capacity decay rate is only 0.065% per cycle after 1000 cycles at 1C. Furthermore, even exposed to heavy sulfur loading (3.61 mg/cm 2 ), they still maintain promising cycle stability. Therefore, such kinds of MOFs derivative with powerful chemical immobilization and catalytic conversion for polysulfides provides a novel guidance for the modification separator and the potential application in the field of high-performance Li-S batteries.

chemistry, physical

Mesoporous TiN Microspheres As an Efficient Polysulfide Barrier for Lithium–sulfur Batteries

Effective Dual Polysulfide Rejection by a Tannic Acid/Fe-III Complex-Coated Separator in Lithium-Sulfur Batteries

TiO2@Porous carbon nanotubes modified separator as polysulfide barrier for lithium-sulfur batteries

2D Ultrathin Titanium Nitride Nanosheets as Separator Coatings for Li-S Batteries

Immobilizing Polysulfides with MXene-Functionalized Separators for Stable Lithium-Sulfur Batteries

Titanium-Containing Metal–Organic Framework Modified Separator for Advanced Lithium–Sulfur Batteries

Partially oxidized Ti3–yNbyC2Tx MXene nanosheets as efficient sulfur hosts and separator modification for Li–S batteries

Tg-C 3 N 4 -coated functional separator as polysulfide barrier of high-performance lithium-sulfur batteries

Metallically conductive TiB2 as a multi-functional separator modifier for improved lithium sulfur batteries

Synthesis of Titanium Molybdenum Nitride-Decorated Electrospun Carbon Nanofiber Membranes as Interlayers to Suppress Polysulfide Shuttling in Lithium–Sulfur Batteries

A Ti<sub>3</sub>C<sub>2</sub>T<sub>x</sub>-Based Composite as Separator Coating for Stable Li-S Batteries

MXene‐Derived Ti n O 2 n− 1 Quantum Dots Distributed on Porous Carbon Nanosheets for Stable and Long‐Life Li–S Batteries: Enhanced Polysulfide Mediation via Defect Engineering

Nitrogen‐Deficient Graphitic Carbon Nitride/Carbon Nanotube as Polysulfide Barrier of High‐Performance Lithium‐Sulfur Batteries

Cobalt/MXene‐derived TiO2 heterostructure as a functional separator coating to trap polysulfide and accelerate redox kinetics for reliable lithium‐sulfur battery

MXene Derivative Ta4C3-Ta2O5 Heterostructure As Bi-Functional Barrier for Li-S Batteries

Mesoporous Boron Carbon Nitride/graphene Modified Separators As Efficient Polysulfides Barrier for Highly Stable Lithium-Sulfur Batteries

Electrospun carbon nanofibers with MnS sulfiphilic sites as efficient polysulfide barriers for high-performance wide-temperature-range Li–S batteries

Design and Synthesis of Novel Pomegranate-Like TiN@MXene Microspheres As Efficient Sulfur Hosts for Advanced Lithium Sulfur Batteries

Ni/SiO2/Graphene-modified separator as a multifunctional polysulfide barrier for advanced lithium-sulfur batteries

Multi‐functional TiO 2 Nanosheets/carbon Nanotubes Modified Separator Enhanced Cycling Performance for Lithium‐sulfur Batteries

Modified separators boost polysulfides adsorption-catalysis in lithium-sulfur batteries from Ni@Co hetero-nanocrystals into CNT-porous carbon dual frameworks