Abstract:In this investigation, the influence of aging time on Cu2ZnSnS4 precursor solutions is assessed, revealing an association reaction among Cu2+, thiourea, and carboxyl groups. The incorporation of hydrochloric acid inhibits this reaction, diminishes the concentration of VSn(−/0) and CuSn(−/0) defects, and mitigates the band‐tailing effect, thereby attaining an optimal efficiency of 11% in a Cu2++Sn2+ system without MgF2. The Sol‐gel precursor solution reaction mechanism has a significant impact on the Cu2ZnSn(S, Se)4 (CZTSSe) solar cells. It is discovered that in the Cu2ZnSnS4 (CZTS) precursor solution (CZTS‐PS) in the preparation, there is an association reaction among Cu2+, thiourea (Tu), and carboxyl (‐COOH), which is an important reason for the undesirable CZTSSe solar cells. The strong association reaction generates excessive Cu2+ ions, forming the CuxSe secondary phase on the surface of the CZTSSe absorber. The secondary phase causes a short circuit and deterioration of gadget performance. Following a 6‐h aging period for the CZTS‐PS, the average photoelectric conversion efficiency (PCE) of the device is enhanced to 8.02%, and there is also an improvement in device uniformity, as evidenced by a decrease in the standard deviation to less than 1. To inhibit the association reaction and eliminate the aging time phenomenon, a strategy is developed using hydrochloric acid to regulate the CZTS‐PS environment. This strategy shifts the REDOX reaction in Cu2++Sn2+ toward the formation of Cu1++Sn4+, leading to a decrease in the defect concentrations of VSn(−/0) and CuSn(−/0), which increases the carrier concentration and reduces the impact of band tailing. The average power conversion efficiency (PCE) of the devices improved from 7.45% to 9.26%, the PCE of the best‐performing CZTSSe solar cells increased from 9.25% to 9.83%, and the consistency among the devices is further enhanced, as indicated by a reduction in the standard deviation from 0.98 to 0.44. Ultimately, the device performance of the Cu2++Sn2+‐DMF system improved by 11.01% (without the MgF2 layer) after optimization. This study serves as a reference for regulating the environment of the CZTS‐PS to further enhance the CZTSSe devices' performance, and the photoelectric conversion efficiency is improved by ≈30%.

Improvement of the Photovoltaic Performance of Cu2ZnSn(SxSe1-x)(4) Solar Cells by Adding Polymer in the Precursor Solution

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Polymer-modified halide perovskite films for efficient and stable planar heterojunction solar cells.

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Synergistic Improvement of Perovskite Film Quality for Efficient Solar Cells Via Multiple Chloride Salt Additives

Enhancement of power conversion efficiency of Ag-substituted Cu2ZnSn(S,Se)4 solar cells via tuning Cu2+/(Cu++Cu2+) percentage in precursor solution

Improvement of grain growth and composition distribution of Cu2ZnSn(S,Se)4 by using chloride-based precursor solution

Regulating Hetero‐Nucleation Enabling Over 14% Efficient Kesterite Solar Cells

High Efficiency Cu2ZnSn(S,Se)4 Solar Cells with Shallow LiZn Acceptor Defects Enabled by Solution‐Based Li Post‐Deposition Treatment

Passivating SnZn Defect and Optimizing Energy Level Alignment via Organic Silicon Salt Incorporation toward Efficient Solution‐Processed CZTSSe Solar Cells

High Efficiency Cu 2 ZnSn(S,Se) 4 Solar Cells with Shallow Li Zn Acceptor Defects Enabled by Solution‐Based Li Post‐Deposition Treatment

Synergistic Crystallization Modulation and Defects Passivation in Kesterite via Anion-Coordinate Precursor Engineering for Efficient Solar Cells

Controlling selenization equilibrium enables high-quality Cu2ZnSn(S, Se)4 absorbers for efficient solar cells

Enhance the Performance of CZTSSe Solar Cells Through Inhibiting the Cu2+, Tu, and (─COOH) Association Reaction

10.24% Efficiency of Flexible Cu2 ZnSn(S,Se)4 Solar Cells by Pre-Evaporation Selenization Technique

Coordination Engineering of Cu-Zn-Sn-S Aqueous Precursor for Efficient Kesterite Solar Cells

[Segmental transplantation of the pancreas in juvenile diabetes: clinical experience at the Munich Transplantation Center].

All-Layer Sputtering-Free Cu2Zn1-xCdxSnS4 Solar Cell with Efficiency Exceeding 7.5%

Polymer additive assisted crystallization of perovskite films for high-performance solar cells

Polyvinylpyrrolidone As Additive for Perovskite Solar Cells with Water and Isopropanol As Solvents