Abstract:A larger specific surface area and three‐dimensional (3D) permeable lamellae carboxylated g‐C3N4 (HCN) are successfully prepared by HNO3 and introduced into the PVDF‐HFP to obtain a high‐performance composite separator. The wettability and ionic conductivity of separator can be improved through the carboxylated HCN. The LFP || Li half‐cell of the separator has a capacity of 71 % at a 5 C rate and 94 % after 400 cycles at a 2 C rate. Polyvinylidene fluoride‐hexafluoropropylene (PVDF‐HFP) is a standard electrolyte membrane and binder material for lithium‐ion batteries (LIBs) because of the benefits of membrane formation and strong mechanical properties. Still, its use is limited due to unavoidable defects such as high crystallinity and poor electrochemical performance. In this paper, a larger specific surface area and three‐dimensional (3D) permeable lamellae carboxylated g‐C3N4 (HCN) were successfully prepared by HNO3 and introduced into the PVDF‐HFP to obtain a high‐performance composite separator. The wettability and electrolyte absorption of PVDF‐HFP separator can be improved through the carboxylated HCN. More crucially, because PVDF‐HFP has several active sites and low crystallinity, adding HCN can greatly increase the ionic conductivity of separators. The ionic conductivity of PH‐HCN at 25 °C is 0.52 S cm−1, 4.7 times higher than the initial PVDF‐HFP membrane, and the oxidation potential can reach 4.8 V. The assembled lithium‐ion batteries half‐cell has a capacity of 71 % at a 5 C rate and 94 % after 400 cycles at a 2 C rate. Therefore, the improved separator has the potential to be applied to high‐performance LIBs.

Composite of Polyvinylidene Fluoride–cellulose Acetate with Al(OH)3 As a Separator for High-Performance Lithium Ion Battery

Preparation and Characterization of PVDF/P（MMA-co-DMAEMA） Separators for Lithium Battery

High Thermal Resistance Polyimide Separators Prepared Via Soluble Precusor and Non-Solvent Induced Phase Separation Process for Lithium Ion Batteries

Polypropylene Separator Coated with a Thin Layer of Poly(lithium Acrylate‐co‐butyl Acrylate) for High‐performance Lithium‐ion Batteries

Novel Configuration of Polyimide Matrix-Enhanced Cross-Linked Gel Separator for High Performance Lithium Ion Batteries

Facile Fabrication of Regenerated Cellulose-Based Separators for High-Performance Lithium-Ion Batteries by Regulating Degrees of Polymerization

Poly(Vinylidene Fluoride) Separators with Dual-Asymmetric Structure for High-Performance Lithium Ion Batteries

A highly-stable separator from an instantly-reformed gel with direct post-solidation for long-cycle high-rate lithium ion batteries.

Composite MnCO3/PVDF-HFP Separator Towards High-Performance Lithium-Ion Batteries

A Polyborate Coated Cellulose Composite Separator for High Performance Lithium Ion Batteries

Ceramic Nanoparticle-Decorated Melt-Electrospun PVDF Nanofiber Membrane with Enhanced Performance as a Lithium-Ion Battery Separator

Cellulose microspheres enhanced polyvinyl alcohol separator for high-performance lithium-ion batteries

Characterization and Preparation of Modified Poly (Vinylidene Fluoride) Separator for Lithium-Ion Battery

A Polyvinylidene Fluoride‐Hexafluoropropylene (PVDF‐HFP)/Carboxylated g‐C3N4 Composite Separator for High‐Performance Lithium‐Ion Batteries

Designing polyimide/polyacrylonitrile/polyimide sandwich composite separator for rechargeable lithium-ion batteries

Sustainable, Heat-Resistant and Flame-Retardant Cellulose-Based Composite Separator for High-Performance Lithium Ion Battery

Fluorinated polymer coated cyanoethyl-chitin nanofiber composite separators for high performance lithium ion batteries

Porous Cellulose Diacetate-Sio 2 Composite Coating on Polyethylene Separator for High-Performance Lithium-Ion Battery

An Efficient, Scalable Route to Robust PVDF-co-HFP/SiO2 Separator for Long-Cycle Lithium Ion Batteries

A Quasi-Solid Composite Separator with High Ductility for Safe and High-Performance Lithium-Ion Batteries