Abstract:Chemical anchor effect is an efficient route for polysulfides immobilization to enhance the performance of Li-S battery. Transition metal oxides are suitable chemical anchor matrix as Lewis acid coordinated with sulfur atoms in the form of Lewis base. Ion bonds may also be formed between anions in transition metal compounds and lithium ions in lithium polysulfides alleviating the shuttle effect. Reducing their crystal sizes to expose more surface active sites and expand surface areas is pivotal to sufficiently immobilize polysulfides. Here, an optimized GFM-2 composite was fabricated, where the 20 nm metal oxide particles aggregated by the 3-5 nm Fe2O3 and Mn3O4 binary crystals are uniformly distributed on the reduced graphene oxide (rGO) nanosheets. A high specific surface area up to 144.9 m(2) g(-1) was obtained for the GFM-2. The modified sulfur@rGO (S@G) cathode obtained by mixing S@G and GFM-2 additive with the mass ratio of 20: 1, presented high specific discharge capacities of 1356.3 and 770.2 mAh g(-1) , respectively, at scan rates of 0.1 and 5C (1C = 1675 mAh g(-1)) under conventional electrolyte dosage with electrolyte/sulfur (E/S) = 30 mL g((s))(-1). and sulfur loading of 1.1 mg cm(-2). The capacity was 1053.5 mAh g(-1) at 1C and maintained at 530.1 mAh g(-1) after 1000 cycles with the low average capacity decay rate of each cycle of 0.049%. Under low electrolyte dosages of E/S = 15 and 8 mL g((s))(-1) the high capacities of 1308.0 and 1230.4 mAh g(-1) could be still obtained at 0.1C, respectively. When the sulfur loading was increased to 2.8 mg cm(-2) and E/S was reduced to 10 mL g((s))(-1), the good capacity of 1163.6 mAh g(-1) was gotten at 0.1C. The high capacity and high cyclic property under different E/S and sulfur loading amounts indicate the potential for practical application of this simple but effective modified sulfur cathode. (C) 2020 Elsevier Ltd. All rights reserved.

A Rgo–cnt Aerogel Covalently Bonded with a Nitrogen-Rich Polymer As a Polysulfide Adsorptive Cathode for High Sulfur Loading Lithium Sulfur Batteries

3D Net-like GO-d-Ti3C2Tx MXene Aerogels with Catalysis/Adsorption Dual Effects for High-Performance Lithium-Sulfur Batteries

A MnO2/Graphene Oxide/Multi-Walled Carbon Nanotubes-Sulfur Composite with Dual-Efficient Polysulfide Adsorption for Improving Lithium-Sulfur Batteries

A MnO 2 /Graphene Oxide/Multi-Walled Carbon Nanotubes-Sulfur Composite with Dual-Efficient Polysulfide Adsorption for Improving Lithium-Sulfur Batteries.

Porous honeycomb-like C3N4/rGO composite as host for high performance Li-S batteries

Reduced Graphene Oxide-MWCNT Organogel Foam for Lithium-Sulfur Battery Cathode

Nitrogen‐Doped Graphene‐Supported Mixed Transition‐Metal Oxide Porous Particles to Confine Polysulfides for Lithium–Sulfur Batteries

Efficient Polysulfide Barrier of a Graphene Aerogel–carbon Nanofibers–ni Network for High-Energy-density Lithium–sulfur Batteries with Ultrahigh Sulfur Content

Reduced graphene oxide wrapped MOFs-derived cobalt-doped porous carbon polyhedrons as sulfur immobilizers as cathodes for high performance lithium sulfur batteries

Hybrid Ascharite/Reduced Graphene Oxide with Polysulfide Adsorption Host for Advanced Lithium-Sulfur Batteries

Rational Design of Graphene Oxide Wrapped Porous Microspheres As High-Performance Sulfur Cathode in Lithium-Sulfur Batteries

A Rgo-Based Fe2O3 and Mn3O4 Binary Crystals Nanocomposite Additive for High Performance Li–S Battery

Strong Lithium Polysulfide Chemisorption on Electroactive Sites of Nitrogen‐Doped Carbon Composites for High‐Performance Lithium–Sulfur Battery Cathodes

Facile Synthesis of Rgo/g-C3n4/cnt Microspheres Via an Ethanol Assisted Spray-Drying Method for High-Performance Lithium-Sulfur Batteries

One‐Pot Hydrothermal‐Derived rGO/MXene/Sulfur Composite Aerogels as Free‐Standing Cathodes in Lithium‐Sulfur Batteries

Graphene-like G-C3n4 Nanosheets/sulfur As Cathode for Lithium–sulfur Battery

Oxidation States Regulation of Cobalt Active Sites through Crystal Surface Engineering for Enhanced Polysulfide Conversion in Lithium–Sulfur Batteries

CoN//Co 9 S 8 co-embedded in reduced graphene oxide as catalyst for catalytic conversion of polysulfides

Strong Lithium Polysulfide Chemisorption on Electroactive Sites of Nitrogen-Doped Carbon Enables High-Performance Lithium-Sulfur Battery Cathodes

Co9S8 nanotube wrapped with graphene oxide as sulfur hosts with ultra-high sulfur content for lithium-sulfur battery

Dual-Protection of A Graphene-Sulfur Composite by A Compact Graphene Skin and an Atomic Layer Deposited Oxide Coating for A Lithium-Sulfur Battery