Abstract:The decrease of superplastic forming temperature and improvement of post-forming mechanical properties are important issues for titanium-based alloys. Ultrafine-grained and homogeneous microstructure are required to improve both processing and mechanical properties. This study focuses on the influence of 0.01–2 wt.% B (boron) on the microstructure and properties of Ti-4Al-3Mo-1V (wt.%) alloys. The microstructure evolution, superplasticity, and room temperature mechanical properties of boron-free and boron-modified alloys were investigated using light optical microscopy, scanning electron microscopy, electron backscatter diffraction, X-ray diffraction analysis, and uniaxial tensile tests. A trace addition of 0.01 to 0.1 wt.% B significantly refined prior β-grains and improved superplasticity. Alloys with minor B and B-free alloy exhibited similar superplastic elongations of 400–1000% in a temperature range of 700–875 °C and strain rate sensitivity coefficient m of 0.4–0.5. Along with this, a trace boron addition provided a stable flow and effectively reduced flow stress values, especially at low temperatures, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of superplastic deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1%. Post-forming heat treatment, including quenching and ageing, increased strength characteristics of the alloys with 0.01 and 0.1% boron by 90–140 MPa and insignificantly decreased ductility. Alloys with 1–2% B exhibited an opposite behavior. For the high-boron alloys, the refinement effect of the prior β-grains was not detected. A high fraction of borides of ~5–11% deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2% B demonstrated non-superplastic behavior and low level of strength properties; meanwhile, the alloy with 1% B exhibited superplasticity at 875 °C with elongation of ~500%, post-forming yield strength of 830 MPa, and ultimate tensile strength of 1020 MPa at room temperature. The differences between minor boron and high boron influence on the grain structure and properties were discussed and the mechanisms of the boron influence were suggested.

Effects of Boron on the Mechanical Properties of the TiAl–Ti3Al Alloy: A First-Principles Investigation

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Effects of Boron on Microstructure Evolution and Mechanical Properties in Ti46Al8Nb2.6C0.8Ta Alloys

Effect of Boron on Microstructure and Mechanical Properties of Cast Ti-44al6-Nb Ingots

Effects of boron on the mechanical behaviour of a Ni-rich NiAl alloy

The effect of boron addition on the deformation behavior and microstructure of β-solidify TiAl alloys

Effect of boron on the structural stability, mechanical properties, and electronic structures of γ′-Ni3Al in TLP joints of nickel-based single-crystal alloys

Effects Boron on Microstructure and Mechanical Properties of Zr3al-Based Alloys

Effects of Carbon and Boron Addition on Microstructure and Mechanical Properties of TiAl Alloys

Effects of Boron Addition on the Microstructure and Mechanical Property of As-Cast Ti-46.5al-8nb Alloy

Effect of Boron on the Microstructure, Superplastic Behavior, and Mechanical Properties of Ti-4Al-3Mo-1V Alloy

Effects of Doped Elements (Si, Cr, W and Nb) on the Stability, Mechanical Properties and Electronic Structures of MoAlB Phase by the First-Principles Calculation

The effect of boron on charge density distribution in Ni3Al

Formation and Kinds of Boride on Microstructure Evolution and Mechanical Properties in Ti47.5Al2.0Cr2.0NbxB Alloys

Solidification Features of Ti45Al Alloys with Different Boron Addition

The effect of boron addition on the high-temperature properties and microstructure evolution of high Nb containing TiAl alloys

First-principles studies of effects of interstitial boron and carbon on the structural, elastic, and electronic properties of Ni solution and Ni3Al intermetallics*

Boride Formation, Microstructure Evolution, and Mechanical Properties of Ti42Al6Nb2.6C0.8Ta Alloyed by Boron

Simultaneously improved strength and ductility of low-cost Ti-Al-V-Fe alloy with TiB 2 addition and thermomechanical processing

Effects of boron defects on mechanical strengths of TiB2 at high temperature: ab initio molecular dynamics studies

The Effect of Nb Doping on the Properties of Ti-Al Intermetallic Compounds Using First-Principles Calculations