Abstract:With the development in additive manufacturing, the use of surface treatments for gas turbine design applications has greatly expanded. An experimental investigation of the pressure loss and heat transfer characteristics within impingement jet arrays with arrays of target surface micro cooling units is presented. The discharge coefficient and Nusselt number are measured and determined for an evaluation of the pressure loss of the flow system and heat transfer level, respectively. Considered are effects of impingement jet Reynolds number ranging from 1000 to 15,000 and micro cooling units (square pin fin) height (h) with associated values of 0.01, 0.02, 0.05, 0.2, and 0.4 D, where D is the impingement hole diameter. Presented are variations of Nusselt number, and Nusselt number ratio, discharge coefficient, discharge coefficient ratio, discharge coefficient correlation. Depending upon the micro cooling unit height, discharge coefficient ratios slightly decrease with height, and the ratio values generally remain unit value (1.0). When Rej = 1000 and 2500 for several cooling units height values, discharge coefficient ratios show the pressure loss decreases about 2–18% and 3–6%, respectively, when compared to the data of a baseline smooth target surface plate. The observed phenomenon is due to the effects of flow blockage of micro cooing units, local flow separation, and near-wall viscous sublayer reattachment. Results also show that heat transfer levels increase 20–300% for some of the tested toughened target surface plates when compared to smooth target surface plates. The heat transfer level enhancement is because of an increase in thermal transport and near-wall mixing, as well as the increased wetted area. In addition, micro cooling units elements break the viscous sublayer and cause greater turbulence intensity when compared to the smooth target surface. Overall, results demonstrate that the target surface micro cooling units do not result in a visible increment in pressure loss and reduce pressure loss of the flow system for some of the tested patterns. Moreover, results show the significant ability of micro cooling units to enhance the surface heat transfer capability of impingement cooling relative to smooth target surfaces.

Effect of Reynolds Number, Hole Patterns, and Hole Inclination on Cooling Performance of an Impinging Jet Array—Part I: Convective Heat Transfer Results and Optimization

Effect of Reynolds Number, Hole Patterns, Target Plate Thickness on Cooling Performance of an Impinging Jet Array: Part Ii - Conjugate Heat Transfer Results and Optimization

Experimental Investigation of Local and Average Heat Transfer Coefficients under an Inline Impinging Jet Array, Including Jets with Low Impingement Distance and Inclined Angle

Heat Transfer and Flow Characteristics of the Jet Array Impingement

Experimental Heat Transfer and Cooling Effectiveness over an Effusion Wall with Internal Jet-Array Impingement: Influence of Hole Arrangement

Effect Of Narrow Jet Spacing On Impinging Flow And Heat Transfer

Influences of Micro Pin-Fin on Jet Array Impingement Heat Transfer: Effects of Jet to Target Distance, Micro Pin-Fin Shapes, Height, and Reynolds Number

Effect of jet-jet spacing on convective heat transfer to confined, impinging arrays of axisymmetric air jets

Experimental Investigation of Micro Cooling Units on Impingement Jet Array Flow Pressure Loss and Heat Transfer Characteristics

Effect of Film Extraction on Impingement Heat Transfer Characteristics of Jet Arrays on Spherical-Dimpled Surfaces

Numerical Investigation and Parameter Sensitivity Analysis on Flow and Heat Transfer Performance of Jet Array Impingement Cooling in a Quasi-Leading-Edge Channel

Experimental and Numerical Investigations of Extended Jet Effects on Multiple-Jet Impingement Heat Transfer Characteristics

Optimum Jet-To-Jet Spacing of Heat Transfer for Staggered Arrays of Impinging Air Jets

Effect of the Nozzle Geometry on Flow Field and Heat Transfer in Annular Jet Impingement

Numerical investigation on the heat transfer performance of array jet impingement cooling with sinusoidal-corrugated target plate

Numerical analysis of jet impingement cooling with elongated nozzle holes on a curved surface roughened with V-shaped ribs

Flow and Heat Transfer Characteristics of Micro Pin-Fins under Jet Impingement Arrays

Thermal performance of impinging jet-row onto trapezoidal channel with different effusion and discharge conditions

Numerical Simulation of the Flow and Heat Transfer Characteristics of Sweeping and Direct Jets on a Flat Plate with Film Holes

Length to Diameter Ratio Effect on Heat Transfer Performance of Simple and Compound Angle Holes in Thin-Wall Airfoil Cooling

Numerical investigation on vane leading edge impingement cooling performance under influences of ribs established between adjacent jets