Design of a ΣΔ Audio DAC

Feng Zheng-he

2004-01-01

Abstract:The design of a 13-bit and 8 kHz audio band ΣΔ DAC for portable device is presented. A third-order single-loop ΣΔ is implemented with only two adders. Combined with a class-D power amplifier, the maximum output power is 90 mW. Simulation shows that a power efficiency of 86.2% is achieved, and the peak SNR is 80 dB.

What problem does this paper attempt to address?

Design of Analog Circuits in Multi-Bit Quantized Audio DAC

HAN Yan,LIAO Lu,HUANG Xiao-wei,ZHANG Hao,WANG Hao

DOI: https://doi.org/10.3785/j.issn.1008-973x.2011.09.010

2011-01-01

Abstract:An analog circuit with high resolution and low power in a sigma-delta(Σ-Δ) digital-to-analog converter(DAC) was designed.By adopting 4-bit quantized technique,this DAC not only enhances the stability of the modulator,reduces the power consumption and the occupied area,but also reduces the system requirements for the back-end low-pass filter.Realizing methods of different modules were given,besides,design techniques in crucial modules that generated non-linearity,such as switched-capacitors and bandgap reference,were discussed.This design was fabricated in SMIC 0.18 μm mixed-signal CMOS process and verified.The measured results showed that the chip had a peak SNDR of 89 dB and a 96 dB dynamic range(DR),and consumed a total power of 19.1 mW,and this value droped to 9.1 mW without buffers.Moreover,the prototype yield was 90%,achieving high precision and low power dissipation.
An 18-Bit High Performance Audio Sigma-Delta D/A Converter

Zhang Hao,Huang Xiaowei,Han Yan,Ray C Cheung,Han Xiaoxia,Wang Hao,Liang Guo

DOI: https://doi.org/10.1088/1674-4926/31/7/075002

2010-01-01

Journal of Semiconductors

Abstract:A multi-bit quantized high performance sigma-delta (Sigma-Delta) audio DAC is presented. Compared to its single-bit counterpart, the multi-bit quantization offers many advantages, such as simpler Sigma-Delta modulator circuit, lower clock frequency and smaller spurious tones. With the data weighted average (DWA) mismatch shaping algorithm, element mismatch errors induced by multi-bit quantization can be pushed out of the signal band, hence the noise floor inside the signal band is greatly lowered. To cope with the crosstalk between digital and analog circuits, every analog component is surrounded by a guard ring, which is an innovative attempt. The 18-bit DAC with the above techniques, which is implemented in a 0.18 mu m mixed-signal CMOS process, occupies a core area of 1.86 mm(2). The measured dynamic range (DR) and peak SNDR are 96 dB and 88 dB, respectively.
A Low-Power Inverter-Based ΣΔ Analog-to-digital Converter for Audio Applications

XiaoPeng Liu,Yan Han,XiaoXia Han,Hao Luo,Ray C. C. Cheung,TianLin Cao

DOI: https://doi.org/10.1007/s11432-013-4999-y

2014-01-01

Science China Information Sciences

Abstract:This paper presents a design for a low-power, high-resolution audio ΣΔ analog-to-digital converter (ADC) based on a novel gain-boost class-C inverter. The gain-boost class-C inverter behaves as a sub-threshold amplifier, thereby minimizing power dissipation. The proposed ADC chip is fabricated in a SMIC 65-nm CMOS process with a die area of 0.63 mm2. With 1.2 V of supply voltage, the ADC chip achieves a peak signal-to-noise-plus-distortion-ratio (SNDR) of 92 dB and a dynamic range (DR) of 97 dB over the 20 kHz audio band, consuming only 1.13 mW. These results make the ADC particularly suitable for portable electronics applications.
An 18-Bit High Performance Audio ∑-△D/A Converter

heiji ikoma,koji oka

DOI: https://doi.org/10.1088/1674-4926/31/7/075002

2010-01-01

Journal of Semiconductors

Abstract:A multi-bit quantized high performance sigma-delta (U-A) audio DAC is presented. Compared to its single- bit counterpart, the multi-bit quantization offers many advantages, such as simpler U-A modulator circuit, lower clock frequency and smaller spurious tones. With the data weighted average (DWA) mismatch shaping algorithm, element mismatch errors induced by multi-bit quantization can be pushed out of the signal band, hence the noise floor inside the signal band is greatly lowered. To cope with the crosstalk between digital and analog circuits, every analog component is surrounded by a guard ring, which is an innovative attempt. The 18-bit DAC with the above techniques, which is implemented in a 0.18 m mixed-signal CMOS process, occupies a core area of 1.86 mm 2 . The measured dynamic range (DR) and peak SNDR are 96 dB and 88 dB, respectively.
A High-Performance,Low-Power ΣΔ Modulator for Digital Audio Applications

Ma Shaoyu,Han Yan,Huang Xiaowei,Yang Liwu

DOI: https://doi.org/10.3321/j.issn:0253-4177.2008.10.038

2008-01-01

Chinese Journal of Semiconductors

Abstract:A third-order low-power ΣΔ modulator for a high-end 18bit audio-band analog-to-digital converter is developed.The modulator is based on a 2-1 cascaded architecture with optimized coefficients to extend the dynamic range and reduce the spectrum tones.The gate-source bootstrapping technique is employed to enhance the sampling switch linearity.A power-efficient class A/AB operational transconductance amplifier (OTA) is proposed,which achieves a high slew rate of 100V/μs with only 0.8mA current consumption.The OTA designed for the second and third integrators is a scaled version of the first OTA,which allows for further power reduction.The modulator is implemented in SMIC mixed-signal 0.18μm CMOS technology,and the area is 1.1mm × 1.0mm.Experimental results indicate a peak signal-to-noise-and-distortion ratio (SNDR) of 91dB and a dynamic range of 94dB over a 22.05kHz bandwidth.The chip operates under a 3.3V power supply with a power dissipation of 6.8mW,which is suitable for high-performance,low-power audio ADC applications.
Research and Implementation of A Low-power High-linearity Audio ΣΔ ADC In 65nm Process

曹天霖,孙颖,韩雁,梁国,廖璐,罗豪

2013-01-01

Abstract:We designed an audio ΣΔ ADC which has low power consumption and high linearity.The proposed ΣΔ ADC contains a 2-1 cascaded 1-bit ΣΔ modulator and a low-power,area-efficient digital decimation filter which is designed using RAM and ROM.This chip has been implemented in SMIC 65nm mixed-signal 1P8M CMOS standard silicon process,and the die area is 0.581mm 2.Experiment results shown that 90dB signal to noise plus distortion ratio(SNDR) and 93dB dynamic range(DR) are achieved within 22.05kHz audio band,at 5M Hz sample rate.The ADC’s power dissipation is 2.2mW under 1.2V supply voltage,which means that this chip obtains high-performance and low-power at the same time.
A High-Performance, Low-Power Σ Δ ADC for Digital Audio Applications

Luo Hao,Han Yan,Ray C. C. Cheung,Han Xiaoxia,Ma Shaoyu,Ying Peng,Zhu Dazhong

DOI: https://doi.org/10.1088/1674-4926/31/5/055009

2010-01-01

Abstract:A high-performance low-power Sigma triangle analog-to-digital converter (ADC) for digital audio applications is described. It consists of a 2-1 cascaded Sigma triangle modulator and a decimation filter. Various design optimizations are implemented in the system design, circuit implementation and layout design, including a high-overload-level coefficient-optimized modulator architecture, a power-efficient class A/AB operational transconductance amplifier, as well as a multi-stage decimation filter conserving area and power consumption. The ADC is implemented in the SMIC 0.18-mu m CMOS mixed-signal process. The experimental chip achieves a peak signal-to-noise-plus-distortion ratio of 90 dB and a dynamic range of 94 dB over 22.05-kHz audio band and occupies 2.1 mm(,)(2) which dissipates only 2.1 mA quiescent current in the analog circuits.
A 65-Nm Low-Power High-Linearity ΣΔ ADC for Audio Applications

Lu Liao,Ying Sun,Yan Han,Guo Liang,Hao Luo,XiaoPeng Liu

DOI: https://doi.org/10.1007/s11432-013-4784-y

2013-01-01

Science China Information Sciences

Abstract:This paper presents a low-power high linearity ΣΔ analog-to-digital converter (ADC) for audio applications. By adopting low noise large output swing operational amplifiers in a 2–1 cascaded modulator, not only can the noise floor be reduced, but the input signal range can also be enlarged. A low-power, area-efficient digital decimation filter was also designed to decrease the area and the power cost. The ADC was fabricated in the SMIC 65 nm single-poly-eight-metal (1P8M) mixed-signal complementary metal-oxide-semiconductor (CMOS) process with a die area of 0.36 mm 2 . Measurement results showed that a 90 dB peak signal to noise plus distortion ratio (SNDR) and a 93 dB dynamic range (DR) were achieved over the 22.05 kHz audio band. The power dissipation was 2.2 mW from 1.2 V power supply, which is suitable for audio codec applications.
Design and Realization of A ΣΔPower DAC for Audio Application

HUANG Wei,ZHENG Shi-yuan,LI Hui

DOI: https://doi.org/10.3969/j.issn.1002-8684.2007.z1.006

2007-01-01

Abstract:A high precision sigma-delta power digital-to-analog converter has been designed for audio application. Some keys of the design, circuit details and simulation results are presented in this paper. Circuit of the sigma-delta power DAC has been designed, simulated and implemented by Synopsys tools. The design has been adopted in MP3 products. The performance is perfect.
A Σδ Modulator Using Gain-Boost Class-C Inverter for Audio Applications.

Hao Luo,Yan Han,Ray C. C. Cheung,Tianlin Cao,Xiaopeng Liu,Feng Gao

DOI: https://doi.org/10.1142/s0218126613400240

2013-01-01

Journal of Circuits Systems and Computers

Abstract:This paper provides an audio 2-1 cascaded ΣΔ modulator using a novel gain-boost class-C inverter. The gain-boost class-C inverter behaves as a subthreshold amplifier. By introducing a gain-boost module, the inverter DC-gain is increased from 48 dB to 67 dB. The gain-boost class-C inverter consumes 57 μW at 1.2-V supply, where the gain-boost module consumes only 3 μW. In addition, an on-chip body bias technique is introduced to compensate the process and supply voltage variations of the class-C inverter. The proposed inverter-based ΣΔ modulator chip is implemented in 0.13-μm CMOS process, and achieves 86-dB peak-signal to noise and distortion ratio (SNDR) and 90-dB dynamic range (DR) over 22.05-KHz bandwidth at 1.2-V supply consuming 360 μW, which demonstrates that the gain-boost class-C inverter is particularly suitable for micro-power high-resolution applications.
The Design and FPGA Verification of Interpolation Filter Used in △-∑ DAC

CHEN Lei,HAN Yan

DOI: https://doi.org/10.3969/j.issn.1001-9146.2006.05.017

2006-01-01

Abstract:This paper describes a general structure,area-optimized interpolation filter used in the Delta-Sigma Digital-to-Analog converter(DAC) intended for the portable digital audio system.The whole filter system simulation,verilog implement and FPGA verification are processed,the signal-to-noise(S/N) achieves 115 dB and the total area is small enough which has good prospect for the audio applications.
The Design and FPGA Verification of a General Structure, Area-optimized Interpolation Filter Used in /spl Delta/-/spl Sigma/ DAC

Xiaowei Huang,Yan Han,Lei Chen

DOI: https://doi.org/10.1109/icsict.2006.306632

2006-01-01

Abstract:This paper describes a general structure, area-optimized interpolation filter used in the Delta-Sigma digital-to-analog converter (DAC) intended for the portable digital audio system. The whole filter system simulation, verilog implement and FPGA verification are processing, the signal-to-noise(S/N) achieves 115 dB and the total area is small enough which has good prospect for the audio applications
A 0.18 μm Single-poly CMOS ∑-△ Modulator for Digital Audio Applications

Shaoyu MA,Yan HAN,Xiaowei HUANG

DOI: https://doi.org/10.3969/j.issn.1000-3819.2009.03.023

2009-01-01

Abstract:This paper presents a third-order cascaded sigma-delta modulator for 18 bit audio-band analog-to-digital conversion.The design is based on a modified cascaded architecture of a second-order modulator stage followed by a first-order stage with reduced gain in the first integrator to increase the dynamic range.The gate-source bootstrapping technique is used to enhance the sampling switch linearity.The modulator is implemented in SMIC 0.18 μm,single-poly CMOS process using MIM capacitors.Experimental results indicate a peak signal-to-noise-and-distortion ratio(SNDR)of 90 dB and dynamic range of 94 dB over a 22.05 kHz bandwidth.
Low-power High-Linearity Sigma-Delta Modulator for Audio Applications

GUO Qing,MA Shao-yu,HUANG Xiao-wei,HAN Yan

DOI: https://doi.org/10.3785/j.issn.1008-973x.2009.02.014

2009-01-01

Abstract:A low-power high-linearity sigma-delta modulator for digital audio analog-to-digital converter was presented,which used an improved cascaded sigma-delta noise-shaper with reduced sensitivity to the operational amplifier nonlinearity.High-linearity sampling was achieved with a novel bootstrapped switch.A low-power operational amplifier was designed with a class AB output stage,which was at least 2-times more power efficient than a regular folded-cascode amplifier.The modulator was implemented in a SMIC standard 0.18 μm CMOS process.Simulation showed that the signal to noise-plus-distortion ratio(SNDR) was 111.8 dB and the dynamic range(DR) was 115 dB under all temperature and process corner conditions.The power consumption of the proposed modulator was 2.6 mW power from a 3 V supply,suitable for the low power audio Codec applications.
An audio cascaded ΣΔ modulator using gain-boost class-C inverter

hao luo,yan han,xiaopeng liu,guo liang,lu liao

DOI: https://doi.org/10.1109/EDSSC.2011.6117686

2011-01-01

Abstract:This paper provides an audio 2-1 cascaded ΣΔ modulator using a novel gain-boost class-C inverter. By introducing a 3-μW gain-boost module, the inverter DC-gain is increased from 48dB to 67dB. The proposed inverter-based ΣΔ modulator chip is implemented in 0.13-μm CMOS process, and achieves 86-dB peak-SNDR, 89-dB peak-SNR and 90-dB DR over 22.05-KHz bandwidth at 1.2-V supply consuming 360μW, which demonstrates that the gain-boost class-C inverter is particularly suitable for micro-power high-resolution applications.
A 200 KHz Bandwidth ΣΔ DAC with a Spur Free Modulator

Chen Yaya,Zhang Shifeng,Cao Tianlin,Han Xiaoxia,Ray C. C. Cheung,Han Yan

DOI: https://doi.org/10.1109/icsict.2016.7999071

2016-01-01

Abstract:This paper creatively presents a sigma-delta digital to analog converter (ΣΔDAC) which achieves 88.5 dB signal to noise and distortion ratio (SNDR) in the 200 KHz bandwidth. The proposed modulator with a high pass dither block can eliminate harmonic spurs without increasing the noise floor in band. In addition, a 2nd-order vector feedback dynamic element match (VFBDEM) provides a good harmonic suppression via mismatch noise shaping. What's more, the cut-off frequency of the proposed modified model of the 1st-order low-pass SC DAC is accordance with that of ΣΔDAC, consequently, filtering out high frequency noise to alleviate the SNDR decrease caused by clock jitter.
An Audio Cascaded Sigma Delta Modulator Using Gain-Boost Class-C Inverter

Hao Luo,Yan Han,Xiaopeng Liu,Guo Liang,Lu Liao

2011-01-01

Abstract:This paper provides an audio 2-1 cascaded Sigma Delta modulator using a novel gain-boost class-C inverter. By introducing a 3-mu W gain-boost module, the inverter DC-gain is increased from 48dB to 67dB. The proposed inverter-based Sigma Delta modulator chip is implemented in 0.13-mu m CMOS process, and achieves 86-dB peak-SNDR, 89-dB peak-SNR and 90-dB DR over 22.05-KHz bandwidth at 1.2-V supply consuming 360 mu W, which demonstrates that the gain-boost class-C inverter is particularly suitable for micro-power high-resolution applications.
Low Power Audio Δ-Σ Digital-to-Analog Converter

LI Dong-mei

2008-01-01

Abstract:A monolithic 16-bit Δ-Σ D/A converter was presented,which was comprised of an interpolator,a Δ-Σ modulator and a power-efficient switching(Class D amplifier) output stage.Fabricated in a 0.18 μm standard CMOS process,this D/A converter can implement 16-bit resolution with a dynamic range of 97 dB and signal band of 8 kHz.An efficiency of 90% is achieved for an 8 Ω speaker.The maximum output power is 100 mW from a single 1.8 V power supply,and the third harmonics is less than-100 dB.This chip can be used in audio applications,such as hearing aid or mp3 players,where the power budget is limited.
An Efficient Digital Front-End for 16-Bit Audio Delta-Sigma D/A Converter

Jing Zhao,Xiaobo Wu,Mi Zhao,Tong Wu

DOI: https://doi.org/10.1007/978-3-642-21747-0_91

2011-01-01

Abstract:In order to save area and achieve high SNDR as well, an efficient digital front-end of a 16-bit DAC for audio application, including a 4-stage interpolator and a 4th-order Δ-Σ modulator with improved DWA technique is proposed. Poly-phase structure and CSD coding method are used for interpolator to save area. An improved DWA technique named as DCSDWA is applied for the Δ-Σ modulator with a 15-level quantizer to eliminate the mismatch errors in multi-bit DAC so as to yield high SNDR. Verified by FPGA in Altera Quartus II synthesis environment, the proposed design yields 115-dB DR and 108.4-dB SNDR for a -6-dBFS sine-wave input, as well as 68-dB stopband attenuation and less than 0.008-dB passband ripple for the interpolator, which indicate the proposed work meets the design requirements well.
A 90db DR Audio Delta-Sigma DAC with Headphone Driver for Hearing Aid

Xiaoliang Yao,Liyuan Liu,Dongmei Li,Liangdong Chen

DOI: https://doi.org/10.1109/cisp.2010.5646870

2010-01-01

Abstract:This paper presents the design and implementation of a single chip audio delta-sigma (ΔΣ) DAC with headphone driver for hearing aid. It consists of a digital interpolation filter, a ΔΣ modulator, a digital low-pass filter (DLPF) encoder and a class D output stage. A structure of chain of integrators with feedforward summation and local resonator feedbacks is adopted for ΔΣ modulator to shape quantization noise. Differing from the basic structure of ΔΣ DAC, a class D output stage playing the role of headphone driver instead of the internal D/A converter is adopted. It is implemented in a 0.18 μm standard CMOS process, the die area is 2.46 mm2. The ΔΣ DAC with headphone driver achieves 85.6 dB peak SNDR and 90 dB dynamic range (DR) and it consumes 4.3 mW with a 376 Ω hearing aid headphone load.

Design of a ΣΔ Audio DAC

Design of Analog Circuits in Multi-Bit Quantized Audio DAC

An 18-Bit High Performance Audio Sigma-Delta D/A Converter

A Low-Power Inverter-Based ΣΔ Analog-to-digital Converter for Audio Applications

An 18-Bit High Performance Audio ∑-△D/A Converter

A High-Performance,Low-Power ΣΔ Modulator for Digital Audio Applications

Research and Implementation of A Low-power High-linearity Audio ΣΔ ADC In 65nm Process

A High-Performance, Low-Power Σ Δ ADC for Digital Audio Applications

A 65-Nm Low-Power High-Linearity ΣΔ ADC for Audio Applications

Design and Realization of A ΣΔPower DAC for Audio Application

A Σδ Modulator Using Gain-Boost Class-C Inverter for Audio Applications.

The Design and FPGA Verification of Interpolation Filter Used in △-∑ DAC

The Design and FPGA Verification of a General Structure, Area-optimized Interpolation Filter Used in /spl Delta/-/spl Sigma/ DAC

A 0.18 μm Single-poly CMOS ∑-△ Modulator for Digital Audio Applications

Low-power High-Linearity Sigma-Delta Modulator for Audio Applications

An audio cascaded ΣΔ modulator using gain-boost class-C inverter

A 200 KHz Bandwidth ΣΔ DAC with a Spur Free Modulator

An Audio Cascaded Sigma Delta Modulator Using Gain-Boost Class-C Inverter

Low Power Audio Δ-Σ Digital-to-Analog Converter

An Efficient Digital Front-End for 16-Bit Audio Delta-Sigma D/A Converter

A 90db DR Audio Delta-Sigma DAC with Headphone Driver for Hearing Aid