Morphology-controlled Syntheses of Α-Mno2 for Electrochemical Energy Storage.

Weidong He,Wenjin Yang,Chenggang Wang,Xiaolong Deng,Baodan Liu,Xijin Xu

DOI: https://doi.org/10.1039/c6cp02548j

IF: 3.3

2016-01-01

Physical Chemistry Chemical Physics

Abstract:The morphological transformations of MnO2 and morphology-dependent electrochemical performance were systematically investigated.

What problem does this paper attempt to address?

Controlled Morphology of One-Dimensional Manganese Dioxide with Dramatic Enhancing Removal Efficiency to Heavy Metal Ions in Aqueous Solution

Xingfa Ma,Mingjun Gao,Xiaochun He,Guang Li

DOI: https://doi.org/10.4028/www.scientific.net/msf.688.23

2011-01-01

Materials Science Forum

Abstract:To examine the effects of morphologies of one-dimentional metal oxides on their surface properties, two typical morphologies of manganese dioxide (one is nanorod, the other is nanofiber) as a model of metal oxide were prepared with hydrothermal approach under similar conditions. The adsorption properties of Pb2+ in aqueous solution were carried out by using surface active group of MnO2 with different morphologies. The results indicated that the sorption capacities for Pb2+ were dramaticly increased via tailoring the morphology of MnO2. The products were characterized with SEM (Scanning Electron Microscopy), XRD (X-ray Diffraction), FTIR (Fourier-Transform Infrared), atomic absorption spectrophotometer, and so on. These results illustrated that it was feasible to improve the removal efficiency of heavy metal ions dramatically in aqueous solution by tailoring the morphology of nanostructured MnO2.
Fabrication and Electrochemical Performance of Nanofibrous Micro-Frameworks of Α-Mno2

Dalai Jin,Ruirui Liu,Xiaochu Ding,Longcheng Wang,Lina Wang,Linhai Yue

DOI: https://doi.org/10.1016/j.partic.2014.01.004

IF: 3.5

2014-01-01

Particuology

Abstract:A facile solid-phase conversion route is proposed to fabricate a micro-framework of alpha-MnO2 with a nanofibrous structure and high porosity. The fabrication is achieved by a three-step process using a preformed manganese tartrate with a rectangular framework as the precursor followed by thermal annealing and hydrothermal oxidation to form the final nanofibrous structure. Evolution of the phase and the morphology are characterized by FESEM, XRD, TG-DTA, and TEM measurements. The electrochemically active material alpha-MnO2 exhibits both attractive stability of the Coulombic efficiency after long-term cyclic charging/discharging and acceptable specific capacitance. (C) 2014 Published by Elsevier B.V.
Controllable Hydrothermal Synthesis of Manganese Dioxide Nanostructures: Shape Evolution, Growth Mechanism and Electrochemical Properties

Xiaochuan Duan,Jiaqin Yang,Haiyan Gao,Jianmin Ma,Lifang Jiao,Wenjun Zheng

DOI: https://doi.org/10.1039/c2ce06587h

IF: 3.756

2012-01-01

CrystEngComm

Abstract:In this work, four well-defined morphologies, including nanorod, nanowire, nanoflower and nanowall, of MnO2 nanostructures with different crystal phases (alpha-, beta-, and delta-MnO2) have been synthesized employing a simple hydrothermal process. The samples are characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), energy-dispersive X-ray spectroscopy (EDS), and Brunauer-Emmett-Teller (BET) spectrometry. Our experimental results demonstrate that the concentration of KMnO4 plays a key role in forming different shapes and phases of MnO2 nanostructures. Specifically, the K+ concentration can affect the crystal phase of MnO2 seeds in the nucleation processes and the decomposition rate of MnO4- can influence the number of MnO2 nuclei at the initial nucleating stage and also can affect the subsequent crystal growth process. Moreover, the effects of reaction temperature on the morphology of the delta-MnO2 nanowall are systematically studied. The electrochemical performances of the as-prepared MnO2 as the positive material of rechargeable Li-ion batteries have also been researched. It is found that the alpha-MnO2 nanowall possesses largely enhanced electrochemical activity compared to alpha-MnO2 nanowires and beta-MnO2 nanorods. The vast difference in electrochemical activity is discussed in terms of the morphology, crystal phase and specific surface area of MnO2 nanostructures. It is highly expected that these findings are useful in understanding the formation of MnO2 nanocrystals with different morphologies, which are also applicable to other metal oxides nanocrystals.
Morphology-conserved Transformation: Synthesis of Hierarchical Mesoporous Nanostructures of Mn2O3 and the Nanostructural Effects on Li-ion Insertion/deinsertion Properties

Yongcai Qiu,Gui-Liang Xu,Keyou Yan,Hui Sun,Junwu Xiao,Shihe Yang,Shi-Gang Sun,Limin Jin,Hong Deng

DOI: https://doi.org/10.1039/c1jm00011j

2011-01-01

Journal of Materials Chemistry

Abstract:By means of morphology-conserved transformation, we have synthesized hierarchically structured Mn2O3 nanomaterials with different morphologies and pore structures. The key step of this method consists of the formation of a precursor containing the target materials interlaced with the judiciously chosen polyol-based organic molecules, which are subsequently knocked out to generate the final nanomaterials. In the present work, two kinds of precursor morphologies, oval-shaped and straw-sheaf-shaped, have been selectively prepared by hydrothermal treatment of different functional polyol molecules (oval-shape with fructose and straw-sheaf-shape with β-cyclodextrin) and potassium permanganate. Thermal decomposition of the precursors resulted in the formation of mesoporous Mn2O3 maintaining the original morphologies, as revealed by extensive characterization. These novel hierarchical nanostructures with different pore sizes/structures prompted us to examine their potential as anode materials for lithium ion batteries (LIBs). The electrochemical results with reference to LIBs show that both of our mesoporous Mn2O3 nanomaterials deliver high reversible capacities and excellent cycling stabilities at a current density of 200 mA g−1 compared to the commercial Mn2O3 nanoparticles. Moreover, the straw-sheaf-shaped Mn2O3 exhibits a higher specific capacity and a better cycling performance than the oval-shaped one, due to the relatively higher surface area and the peculiar nanostrip structure resulting in the reduced length for lithium ion diffusion. Morphology-conserved transformation yields two kinds of hierarchical mesoporous Mn2O3 nanomaterials with high capacities and cycling stabilities for lithium ion batteries.
Tuning the Morphologies of MnO/C Hybrids by Space Constraint Assembly of Mn-MOFs for High Performance Li Ion Batteries

Dan Sun,Yougen Tang,Delai Ye,Jun Yan,Haoshen Zhou,Haiyan Wang

DOI: https://doi.org/10.1021/acsami.6b14801

2017-01-01

Abstract:Morphology controllable fabrication of electrode materials is of great significance but is still a major challenge for constructing advanced Li ion batteries. Herein, we propose a novel space constraint assembly approach to tune the morphology of Mn(terephthalic acid) (PTA)-MOF, in which benzonic acid was employed as a modulator to adjust the available MOF assembly directions. As a result, Mn(PTA)-MOFs with microquadrangulars, microflakes, and spindle-like microrods morphologies have been achieved. MnO/C hybrids with preserved morphologies were further obtained by self-sacrificial and thermal transformation of Mn(PTA)-MOFs. As anodes for Li ion batteries, these morphologies showed great influence on the electrochemical properties. Owing to the abundant porous structure and unique architecture, the MnO/C spindle-like microrods demonstrated superior electrochemical properties with a high reversible capacity of 1165 mAh g-1 at 0.3 A g-1, excellent rate capability of 580 mAh g-1 at 3 A g-1, and no considerable capacity loss after 200 cycles at 1 A g-1. This strategy could be extended to engineering the morphology of other MOF-derived functional materials in various structure-dependent applications.
Effect of MnO 2 Morphology on Kinetics and Stability in Zinc-Ion Batteries

Ning Gao,Yang Song,Chang Li,Chaoquan Hu

DOI: https://doi.org/10.1021/acsami.3c03437

IF: 9.5

2023-06-03

ACS Applied Materials & Interfaces

Abstract:Research on zinc-ion batteries (ZIBs) with manganese-based cathodes has been severely hindered by their poor cycle stability. This study explores the fundamental parameters that affect the cycle stability of battery systems from a structural stability perspective. MnO(2) electrodes with different classical morphologies and sizes were synthesized via a temperature-controlled coprecipitation strategy. The effects of the morphology and size of the MnO(2) on the overall electrical properties and...

materials science, multidisciplinary,nanoscience & nanotechnology
Controllable Synthesis of Manganese Organic Phosphate with Different Morphologies and Their Derivatives for Supercapacitors

Jingwen Zhao,Qingling Jing,Ting Zhou,Xinhuan Zhang,Wenting Li,Huan Pang

DOI: https://doi.org/10.3390/molecules29174186

IF: 4.6

2024-09-04

Molecules

Abstract:Morphological control of metal-organic frameworks (MOFs) at the micro/nanoscopic scale is critical for optimizing the electrochemical properties of them and their derivatives. In this study, manganese organic phosphate (Mn-MOP) with three distinct two-dimensional (2D) morphologies was synthesized by varying the molar ratio of Mn2+ to phenyl phosphonic acid, and one of the morphologies is a unique palm leaf shape. In addition, a series of 2D Mn-MOP derivatives were obtained by calcination in air at different temperatures. Electrochemical studies showed that 2D Mn-MOP derivative calcined at 550 °C and exhibited a superior specific capacitance of 230.9 F g-1 at 0.5 A g-1 in 3 M KOH electrolyte. The aqueous asymmetric supercapacitor and the constructed flexible solid-state device demonstrated excellent rate performance. This performance reveals the promising application of 2D Mn-MOP materials for energy storage.
Atmosphere Assisted Growth of Mn3O4 Balls for Lithium Batteries

Xiaofei Sun,Zhengyi Xu,Youlong Xu,Xiaona Zhang,Feng Teng,Long Li

DOI: https://doi.org/10.1149/ma2016-03/2/507

2016-01-01

ECS Meeting Abstracts

Abstract:Transition metal oxides MOx (M=Fe, Co, Mn ···) are being extensively investigated as a group of next generation anode materials for rechargeable lithium batteries, because of their high theoretical specific capacities based on conversion reactions during charging/discharging. Manganese oxides are specially considered also for their low cost and environmental friendliness. In this paper, Mn3O4 with different morphologies, i.e. micro-balls and polyhedral particles (Fig. 1), are prepared by tuning the synthesis atmosphere. The crystallographic structure, particle morphology and electrochemical performance are comprehensively studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic cycling. The relationship between the particle structure and battery performance of different shaped Mn3O4will be comparatively discussed. This work is financially supported by the Natural Science Foundation of Shaanxi Province (China, Grant No. 2014JQ2-2007), the National Natural Science Foundation of China (Grant No. 21503158), the Fundamental Research Funds for the Central Universities of China (Grant No. xjj2014044) and the 111 Project (Grant No. B14040). Fig. 1 Figure 1
The energy storage mechanisms of MnO2 in batteries

Xun Guo,Shuo Yang,Donghong Wang,Ao Chen,Yanbo Wang,Pei Li,Guojin Liang,Chunyi Zhi

DOI: https://doi.org/10.1016/j.coelec.2021.100769

IF: 8.5

2021-12-01

Current Opinion in Electrochemistry

Abstract:Manganese dioxide, MnO2, is one of the most promising electrode reactants in metal-ion batteries because of the high specific capacity and comparable voltage. The storage ability for various metal ions is thought to be modulated by the crystal structures of MnO2 and solvent metal ions. Hence, through combing the relationship of the performance (capacity and voltage) with the polymorphs of the MnO2 and metal ions in different solvents (organic and aqueous), three main energy storage mechanisms were found to be responsible for the different electrochemical processes. Furthermore, this review summarizes the main challenge and gives a direction for profound study in the future.

chemistry, physical,electrochemistry,materials science, multidisciplinary
Theory Abide Experimental Investigations on Morphology Driven Enhancement of Electrochemical Energy Storage Performance for Manganese Titanate Perovskites Electrodes

Narasimharao Kitchamsetti,Manopriya Samtham,Pravin N. Didwal,Diwakar Singh,Santosh Bimli,Parameshwar R. Chikate,Dhirendra Kumar Sharma,Dudekula Althaf Basha,Sunil Kumar,Chan-Jin Park,Sudip Chakraborty,Rupesh S. Devan

DOI: https://doi.org/10.2139/ssrn.4073397

2022-01-01

SSRN Electronic Journal

Abstract:The ultrathin 2D morphologies are found efficient in delivering better specific energy and long cycle life performance for supercapacitors. Therefore, we report the effect of morphological transformation from nanoparticles to ultrathin nanodiscs of MnTiO3(MTO) perovskites as an efficient electrode for electrochemical supercapacitor where the interconnected network of stacked ultrathin 2D nanodiscs provided easily accessible sites for efficient diffusion of OH - ions deep inside the electrode material. Ultrathin 2D MTO nanodiscs delivered a specific capacitance of 1513.7 F/g, specific capacity of 103.2 mAh/g, specific power of 1351.9 W/kg, and specific energy of 52.2 Wh/kg. Moreover, 85.1% capacitance retention after 5000 cycles in 2M aq. KOH electrolyte was observed with insignificant morphological deformation of 2D nanodiscs. Corresponding First-principles density functional theory (DFT) calculations revealed that ultrathin 2D morphology produced higher work-function and hence delivered better energy storage performance.
Cations Controlled Growth of Β-Mno2 Crystals with Tunable Facets for Electrochemical Energy Storage

Wentao Yao,Gregory M. Odegard,Zhennan Huang,Yifei Yuan,Hasti Asayesh-Ardakani,Soroosh Sharifi-Asl,Meng Cheng,Boao Song,Ramasubramonian Deivanayagam,Fei Long,Craig R. Friedrich,Khalil Amine,Jun Lu,Reza Shahbazian-Yassar

DOI: https://doi.org/10.1016/j.nanoen.2018.03.057

IF: 17.6

2018-01-01

Nano Energy

Abstract:Engineering crystal facets to enhance their functionalities often require complex processing routes to suppress the growth of surfaces with the lowest thermodynamic energies. Herein, we report a unique method to control the morphologies of beta-MnO2 crystals with different occupancy of {100}/{111} facets through the effect of K+ cations. Combining aberration-corrected scanning transmission electron microscopy (STEM), ultramicrotomy, and dynamic functional theory (DFT) simulation, we clarified that the beta-MnO2 crystals were formed through a direct solid-state phase transition process. Increasing the concentration of K+ cations in the precursor gradually changed the morphology of beta-MnO2 from bipyramid prism ({100}+{111} facets) to an octahedron structure ({111} facets). The K+ cations controlled the morphology of beta-MnO2 by affecting the formation of a-K0.5Mn4O8 intermediate phase and the subsequent phase transition. Utilizing the beta-MnO2 crystals as the cathode for Li-ion batteries showed that highly exposed {111} facets offered beta-MnO2 crystal better rate performance, with similar to 70% capacity retention when the charge-discharge rate increased from 20 mA/g to 200 mA/g. Our work revealed a new mechanism to tune the morphology of this earth-abundant metal oxide crystal, which could be used to adjust its electrochemical performance for different applications, such as supercapacitors and catalysts for metalair batteries and fuel cells.
Preparation and lithium-ion storage properties of micro/nano-structured MnO anode material

LIU Ya-min,ZHAO Xiu-yun,XIA Ding-guo

DOI: https://doi.org/10.3969/j.issn.1002-087X.2012.05.008

2012-01-01

Abstract:The precursor MnCO3 with different morphology was synthesized by different ways.After annealing the precursor MnCO3 under H2/Ar,cubic,spherical,dumbbell-like and ellipsoidal MnO was obtained.The structure and morphology of the products were investigated by X-ray diffraction(XRD),scanning electron microscopy(SEM) and thermogravimetry(TG).The electrochemical performance of MnO with different shapes was tested by the galvanostatically charge and discharge method.The results show that cubic and spherical MnO exhibits higher reversible specific capacity when tested at 0.1 C,keeping 250 mAh/g after 20 cycles.
Structural and electrochemical studies of α-manganese dioxide (α-MnO2)

C.S. Johnson,D.W. Dees,M.F. Mansuetto,M.M. Thackeray,D.R. Vissers,D. Argyriou,C.-K. Loong,L. Christensen

DOI: https://doi.org/10.1016/s0378-7753(96)02633-x

IF: 9.2

1997-10-01

Journal of Power Sources

Abstract:The structural and electrochemical properties of α-MnO2, prepared by acid digestion of Mn2O3, and its lithiated derivatives xLi2O · MnO2 (0 ≤ x ≤ 0.25) have been investigated as insertion compounds in the search for new and viable cathode materials for rechargeable 3 V batteries. The α-MnO2 product fabricated by this technique contains water within the large (2 × 2) channels of the structure; the water can be removed from the α-MnO2 framework without degradation of the structure, and then at least partially replaced by Li2O (lithium oxide). The Li2O-doped α-MnO2 electrodes, described generically as xLi2O · MnO2, stabilize the structure and provide higher capacities on cycling than the parent material. The structures of these α-MnO2-type electrode materials are described, and electrochemical data are presented for both liquid electrolyte and polymer electrolyte Li/α-MnO2 and Li/xLi2O · MnO2 cells.

energy & fuels,materials science, multidisciplinary,electrochemistry,chemistry, physical
Synthesis, characterization and electrochemical behavior of Zn-doped MnO/C submicrospheres for lithium ion batteries

Tingting Feng,Huilan Li,Jie Tan,Yufeng Liang,Wanqiu Zhu,Shu Zhang,Mengqiang Wu

DOI: https://doi.org/10.1016/j.jallcom.2021.163153

IF: 6.2

2022-01-01

Journal of Alloys and Compounds

Abstract:•Zn-MnO/C anode was prepared via Zn evaporation from ZnMn2O4/polydopamine.•The transformation process was detected by multiple techniques.•Hexagonal ZnMn2O4 nanoplates were found in the cycled electrode material.•The mechanism was revealed by ex situ XRD and CV tests for post-cycled electrode.
Synthesis and Electrochemical Performance of Β-Mno2 with Semi-Tubular Morphology

Mingyang Yang,Ping Ni,Yan Li,Xuexia He,Zong-Huai Liu

DOI: https://doi.org/10.1016/j.matchemphys.2010.06.008

IF: 4.778

2010-01-01

Materials Chemistry and Physics

Abstract:β-MnO2 with semi-tubular morphology has been prepared in a mixed solution of KMnO4 and MnCl2 by a facile hydrothermal route without using templates, catalysts, and organic reagents. The structure of the obtained β-MnO2 is systematically investigated by XRD, SEM, and TEM. Results show that the as-prepared β-MnO2 has novel semi-tubular morphology, and its particle shows a diameter of 300–400nm and length up to 1–4μm. The prepared β-MnO2 shows a good electrochemical performance, and delivers a discharge capacity of 195mAhg−1 after 40 cycles between voltage limit of 1.5 and 4.5V at a constant current density of 20mAg−1.
Morphology engineering of high performance binary oxide electrodes

Kunfeng Chen,Congting Sun,Dongfeng Xue

DOI: https://doi.org/10.1039/c4cp03888f

2015-01-14

Abstract:Advances in materials have preceded almost every major technological leap since the beginning of civilization. On the nanoscale and microscale, mastery over the morphology, size, and structure of a material enables control of its properties and enhancement of its usefulness for a given application, such as energy storage. In this review paper, our aim is to present a review of morphology engineering of high performance oxide electrode materials for electrochemical energy storage. We begin with the chemical bonding theory of single crystal growth to direct the growth of morphology-controllable materials. We then focus on the growth of various morphologies of binary oxides and their electrochemical performances for lithium ion batteries and supercapacitors. The morphology-performance relationships are elaborated by selecting examples in which there is already reasonable understanding for this relationship. Based on these comprehensive analyses, we proposed colloidal supercapacitor systems beyond morphology control on the basis of system- and ion-level design. We conclude this article with personal perspectives on the directions toward which future research in this field might take.
Controlled Synthesis of Hierarchical CoxMn3−xO4array Micro-/Nanostructures with Tunable Morphology and Composition As Integrated Electrodes for Lithium-Ion Batteries

Le Yu,Lei Zhang,Hao Bin Wu,Genqiang Zhang,Xiong Wen (David) Lou

DOI: https://doi.org/10.1039/c3ee41181h

IF: 32.5

2013-01-01

Energy & Environmental Science

Abstract:Hierarchical CoxMn3-xO4 array micro-/nanostructures with tunable morphology and composition have been grown on conductive stainless steel with robust adhesion by a facile solvothermal route and a subsequent annealing treatment. By simply controlling the volume ratio of components in the mixed solvent, the morphology of the products can be tailored from hierarchical nanowires to nanosheets. Benefitting from the unique structural features, the resultant CoMn2O4 nanowires and MnCo2O4 nanosheets exhibit excellent electrochemical performance with remarkable specific capacities (540-207 mA h g(-1)) at various current rates (1-10 C) and good cycling stability for highly reversible lithium storage. The enhanced electrochemical performance suggests their promising use as integrated binder-free electrodes for microscale lithium-ion batteries.
MnO2: Morphological and Electrochemical Cycling Effects in MnO2 Nanostructures by 3D Electron Tomography (Adv. Funct. Mater. 21/2014)

wei chen,r b rakhi,qingxiao wang,m n hedhili,h n alshareef

DOI: https://doi.org/10.1002/adfm.201470135

IF: 19

2014-01-01

Advanced Functional Materials

Abstract:Manganese dioxide is considered as one of the most promising materials for supercapacitor energy storage applications. On page 3130, H. N. Alshareef and co-workers present the morphological and electrochemical cycling effects in MnO2 nanostructures by three-dimensional electron tomography. The growth process of the various MnO2 nanostructures is correlated to their electrochemical performance as supercapacitor materials. The study provides significant insight into the growth mechanism, electrochemical performance, and cycling behaviors of nanostructured MnO2.
A Phase Transformation-Resistant Electrode Enabled By A Mno2-Confined Effect For Enhanced Energy Storage

Wei Guo,Chang Yu,Shaofeng Li,Xuedan Song,Ying Yang,Bo Qiu,Changtai Zhao,Huawei Huang,Juan Yang,Xiaotong Han,Dan Li,Jieshan Qiu

DOI: https://doi.org/10.1002/adfm.201901342

IF: 19

2019-01-01

Advanced Functional Materials

Abstract:Although the transition metal oxides/hydroxides are regarded as highly promising and attractive materials for efficient energy storage, a precycling/activation process is usually adopted to stabilize phase components and achieve reversible output. Moreover, the intrinsic mechanism involved in precycling process is not always concerned and remains to be further decoupled. Herein, overcoming the challenges associated with the MnO2-confined effect is proposed, which is enabled by in situ dissolving-out and conversion of Mn species in MnO2 derived from the Co-induced effect. Notably, a high electrochemical stability without activation and a superior initial Coulombic efficiency of 96.2% can be achieved without any precycling or activation process, which increases by 33.5% in comparison to the efficiency of the hybrids without MnO2 surface-confined effect. And a specific capacity up to 164 mAh g(-1) at 2 A g(-1) can be achieved with an excellent capacity retention rate of 90% at 30 A g(-1), which only drops slightly and remains at a high level of 87% even after 5000 cycles. This strategy may function as a model for the design and configuration of highly stable electrodes toward high-efficient energy storage and conversion applications.
Probing the Morphology Dependence, Size Preference and Electron/ion Conductance of Manganese-Based Lithium Transition-Metal Phosphate As Cathode Materials for High-Performance Lithium-Ion Battery

Yan Wang,Faquan Yu

DOI: https://doi.org/10.1016/j.jallcom.2020.156773

IF: 6.2

2021-01-01

Journal of Alloys and Compounds

Abstract:As a promising cathode for next-generation lithium-ion batteries, the morphology dependence, size preference and electron/ion conductance of manganese-based lithium transition-metal phosphate (MLTP) compounds were comprehensively analyzed via synergistic strategies including the surfactant-assisted solvothermal method and surface modification. Variations of morphology, (particle, crystallite and lattice) size and electron/ion conductivity selectively modulated their electrochemical properties. For MLTP cathode materials, the as-prepared small-sized particle with large crystallite and large lattice greatly optimized the cycling stability, reversible capacity and polarization performance, whereas irregular particle morphology mainly inhibited the specific capacity. Meanwhile, the RGO-decorated MLTP-EG12/C cathode material could further unlock the high-rate capability and thermal stability without polarization differences. These regulation mechanisms of morphology, size and conductivity described in this work can be helpful in the development of high-performance cathode materials for lithium-ion batteries.

Morphology-controlled Syntheses of Α-Mno2 for Electrochemical Energy Storage.

Controlled Morphology of One-Dimensional Manganese Dioxide with Dramatic Enhancing Removal Efficiency to Heavy Metal Ions in Aqueous Solution

Fabrication and Electrochemical Performance of Nanofibrous Micro-Frameworks of Α-Mno2

Controllable Hydrothermal Synthesis of Manganese Dioxide Nanostructures: Shape Evolution, Growth Mechanism and Electrochemical Properties

Morphology-conserved Transformation: Synthesis of Hierarchical Mesoporous Nanostructures of Mn2O3 and the Nanostructural Effects on Li-ion Insertion/deinsertion Properties

Tuning the Morphologies of MnO/C Hybrids by Space Constraint Assembly of Mn-MOFs for High Performance Li Ion Batteries

Effect of MnO 2 Morphology on Kinetics and Stability in Zinc-Ion Batteries

Controllable Synthesis of Manganese Organic Phosphate with Different Morphologies and Their Derivatives for Supercapacitors

Atmosphere Assisted Growth of Mn3O4 Balls for Lithium Batteries

The energy storage mechanisms of MnO2 in batteries

Theory Abide Experimental Investigations on Morphology Driven Enhancement of Electrochemical Energy Storage Performance for Manganese Titanate Perovskites Electrodes

Cations Controlled Growth of Β-Mno2 Crystals with Tunable Facets for Electrochemical Energy Storage

Preparation and lithium-ion storage properties of micro/nano-structured MnO anode material

Structural and electrochemical studies of α-manganese dioxide (α-MnO2)

Synthesis, characterization and electrochemical behavior of Zn-doped MnO/C submicrospheres for lithium ion batteries

Synthesis and Electrochemical Performance of Β-Mno2 with Semi-Tubular Morphology

Morphology engineering of high performance binary oxide electrodes

Controlled Synthesis of Hierarchical CoxMn3−xO4array Micro-/Nanostructures with Tunable Morphology and Composition As Integrated Electrodes for Lithium-Ion Batteries

MnO2: Morphological and Electrochemical Cycling Effects in MnO2 Nanostructures by 3D Electron Tomography (Adv. Funct. Mater. 21/2014)

A Phase Transformation-Resistant Electrode Enabled By A Mno2-Confined Effect For Enhanced Energy Storage

Probing the Morphology Dependence, Size Preference and Electron/ion Conductance of Manganese-Based Lithium Transition-Metal Phosphate As Cathode Materials for High-Performance Lithium-Ion Battery