Abstract:High-damping rubber materials utilized in high-damping rubber isolation bearings are frequently subjected to multiple deformations during the occurrence of earthquakes. Typically, large combined compression–shear deformations of the material could potentially cause compressive shear damage to rubber bearings. During this process, visco-hyperelastic properties of rubber materials will greatly change, which would significantly impact the seismic performance of rubber bearings. Thus, to give out a deep insight into their variations, it is necessary and urgent to develop a high-performance numerical method to investigate this process. This paper proposed a visco-hyperelastic constitutive modeling approach for high-damping rubber materials based on the experimental assessment of combined quasi-static compression–cyclic shear deformation process. Within the thermodynamic framework, the Clausius–Duhem inequality associated with the intrinsic dissipation of the material was firstly derived in accordance with the Lagrangian formulism. Then, stress–strain relations were obtained upon considering the occurrence of entropy production due to viscous dissipation. In the model, Stumpf–Marczak strain energy density function, which satisfies the Baker–Ericksen (B–E) inequality, was harnessed to describe the hyperelasticity of the material. By introducing higher orders of strain and strain rates and taking their couplings into account, a generalized viscous dissipation potential was proposed to capture nonlinear strain and strain rate-sensitivity effects of the material. To identify constitutive parameters, the deformation gradient was particularized for the combined quasi-static compression–cyclic shear deformation process. And, an inverse identification procedure was carried out at different levels of compression stress. The prediction results revealed that the proposed model exhibits remarkable prediction ability and adaptivity for different rubber materials during this process. Several new insights were highlighted on the variations of visco-hyperelastic characteristics of high-damping rubber materials with respect to the compression stress. The accuracy of the model was further validated by design parameters including initial shear modulus, secant shear modulus and equivalent viscous damping factor. This work could provide a fundamental guideline for the optimization and reliability analysis of high-damping rubber isolation bearings used in the field of seismic engineering.

A Rate‐dependent Constitutive Model of High Damping Rubber Bearings: Modeling and Experimental Verification

A Simplified Analytical Model for U-shaped Steel Dampers Considering Horizontal Bidirectional Deformation

A Generalized Rate-Dependent Constitutive Law for Elastomeric Bearings

Experimental and Analytical Investigation of the Influence of Compressive Load on Rate-Dependent High-Damping Rubber Bearings

Study on a Pseudo-Elastic Model for High-Damping Rubber

Visco-Hyperelastic Constitutive Modeling for High-Damping Rubber Materials During Combined Quasi-Static Compression–Cyclic Shear Deformation Process

Developing a New Constitutive Model of High Damping Rubber by Combining GRU and Attention Mechanism

Experimental and analytical studies of seismic response of highway bridges isolated by rate-dependent rubber bearings

A novel viscoelastroplastic constitutive model of rubber materials and parameter identification

Generalized Hyper-Viscoelastic Modeling and Experimental Characterization of Unfilled and Carbon Black Filled Natural Rubber for Civil Structural Applications

Hysteretic behavior of high damping rubber bearings under multiaxial excitation

Development and Validation of a Nonlinear Model to Describe the Tension-Compression Behavior of Rubber-Like Base Isolators

Modeling of Hyper-Viscoelastic Properties of High-Damping Rubber Materials during the Cyclic Tension and Compression Process in the Vertical Direction

Seismic Performance Of A Multi-Span Rc Highway Bridge With High Damping Rubber Bearings

Modeling Method of Constitutive Law of Rubber Hyperelasticity Based on Finite Element Simulations

Multi-layered Solid Element for Seismic Analysis of Rubber Bearings Considering Stress Continuity Based on Finite Particle Method

An Experimental Study on the Mechanical Properties of a High Damping Rubber Bearing with Low Shape Factor

An Improved Contact Model for Pounding Simulation of Base-isolated Highway Bridge

Construction of a Rubber Superelastic-Viscoelastic Model and Analysis of Dynamic Response of Structure

Experimental Study of the Dynamic Behavior of High-Damping Rubber-Bearing Isolator

Dynamic Performance Study On The Super High Damping Rubber Isolation Bearings Depend On The Real-Time Substructure Hybrid Loading System