Abstract:Demand for lithium-ion batteries (LIBs) has increased dramatically over the years due to the rapid market expansion of electric vehicles. However, many of the essential components of cathode materials, such as cobalt, nickel, manganese and lithium, are resource-limited and expensive[1]. Therefore, recycling of used LIB cathode materials is very important to conserve resources and the environment. Currently, the lithium secondary battery recycling technology mainly uses wet and dry smelting, but there is a disadvantage of high energy consumption due to the use of strong acid and the smelting process[2-3]. In this study, the cathode active material was separated from a pouch-type lithium secondary battery separated from a portable tablet that was over 10 years old and the chemical, structural, and electrochemical characteristics thereof were investigated. The cathode active materials were dismantled from a pouch-type LIB, which was removed from the tablet produced in 2011. The pouch cell was in a swelling state and the OCV was 0V due to internal short is expected. As a result of TGA analysis, the electrode composition was confirmed to be 92wt% of the cathode active material, 3wt% of the conductive agent, and 3wt% of the binder, respectively. The recovery rate of the active material is the best when a mixed solvent including NMP, heating, and ultrasonic, respectively. Through SEM and EDS analysis, copper metal due to dissolution of the negative electrode current collector was found on the surface of the positive electrode. As shown in Fig. 1, It can be seen that the positive electrode active material recovered using the composite solvent is a positive electrode active material that is a mixture of NCM active material and LMO active material. The XRD results shows a well layered structure and a Co 3 O 4 phase due to lithium deficiency. In order to examine the electrochemical characteristics of the recovered electrode, it was reassembled into a 2032 coin type cell and evaluated, and the discharge capacity of approximately 150mAh/g was recovered as shown in Fig. 2. The positive active material recovered according to the experimental results is estimated to be in a state of insufficient lithium, and a lithium compensation process is planned to be additionally performed in the future.

Recovery of Expired Lithium Carbonate Tablets for LiFePO 4 /C Cathode

The Synchronous Reutilization of the Expired Ferrous Sulfate Granules and Waste Li Foils for LiFePO4/C Cathode

Recovery of Waste Li Foils from Spent Experimental Li-anode Coin Cells for LiFePO4/C Cathode

Regeneration and Performance of LiFePO4 with Li2CO3 and FePO4 As Raw Materials Recovered from Spent LiFePO4 Batteries

Exploiting the Non-Medical Value of Waste Expired Aminophylline for Lithium Ion Battery Anode

Feasibility of Expired Waste Aspirin for Use As Lithium-Ion Battery Anode

A novel acid-free leaching route of recovering Li2CO3 and FePO4 from spent LiFePO4 black powder

Total Component Recovery of Spent LiFePO 4 Cathode Powder: A Leaching-Adsorption Process

A Facile Route for the Efficient Leaching, Recovery, and Regeneration of Lithium and Iron from Waste Lithium Iron Phosphate Cathode Materials

Selective recovery of Li and FePO4 from spent LiFePO4 cathode scraps by organic acids and the properties of the regenerated LiFePO4

The recovery of expired ferrous gluconate and spent Li foils into high performance straw-bundle-like α-LiFeO2/C cathode

Reutilization of the Expired Tetracycline for Lithium Ion Battery Anode.

Recovery and regeneration of LiFePO4 from spent lithium-ion batteries via a novel pretreatment process

Recovery of lithium iron phosphate batteries through electrochemical oxidation in Na2CO3 solutions

Conversion of LiFePO4 to FePO4 via Selective Lithium Bicarbonation: A Direct Pathway Towards Battery Recycling

Direct regeneration of spent LiFePO4 cathode material via a simple solid-phase method

Regenerated LiFePO4/C for scrapped lithium iron phosphate powder batteries by pre-oxidation and reduction method

Research for Electrochemical & Structural Properties of Recycling Cathode Materials for End of Life Lib

Short-Process Regeneration of Highly Stable Spherical LiCoO2 Cathode Materials from Spent Lithium-Ion Batteries through Carbonate Precipitation

Recovery of Li2CO3 from Spent LiFePO4 by Using a Novel Impurity Elimination Process

A green strategy towards fabricating FePO4-graphene oxide for high-performance cathode of lithium/sodium-ion batteries recovered from spent batteries