Abstract:A numerical modeling study, based on 3D finite element method (FEM) simulation and 1D analytical solutions, has been carried out to evaluate the capabilities of two ac methods for measuring in-plane thermal conductivity of thin film deposited on the back of a suspended SiNx membrane setup. Two parallel metal strips are present on the top of the dielectric membrane. One strip (S1) serves as both heater and thermometer, while another one (S2) acts as thermometer only. For a modified phase shift (MPS) method, it is crucial to extract the in-plane thermal diffusivity from the phase shift of the temperature oscillation on S2. It was found that the frequency window for carrying out the data fitting became narrower as the in-plane thermal diffusivity of the composite membrane (<math>α∥,C</math>) increased, primarily due to the failure of the semi-infinite width assumption in the low frequency region. To ensure the validity of the method, the upper limit of <math>α∥,C</math> should not exceed ~1.8 × 10−5 m2 s−1 for the specific membrane dimension under consideration (1 × 1 mm2). On the other hand, inspired by a modified Ångström method proposed by Zhu recently, we suggest a new data reduction methodology which takes advantage of the phase shift on both S1 and S2 as well as the amplitude on S1. Based on the simulation results, it is expected that the non-ideality associated with the three "observables" may be at least partially canceled out. Therefore, the frequency window selection for carrying out the data fitting is not sensitive to the magnitude of <math>α∥,C</math> and the upper limit of measurable <math>αC,∥</math> can be further increased with respect to the MPS method. For typical specimen films whose in-plane thermal conductivity ranges from 0.84 W m−1 K−1 to 50 W m−1 K−1, the method proposed here yields a theoretical measurement uncertainty of less than 5%.

A Predictive Model for Thermal Conductivity of Nano-Ag Sintered Interconnect for a SiC Die

Electrothermal Cosimulation of 3-D Carbon-Based Heterogeneous Interconnects

Implementation Of Temperature Dependent Contact Resistance Model For The Analysis Of Deep Submicron Devices Under Esd

Predicting Effective Thermal Conductivity of Sintered Silver by Microstructural-Simulation-Based Machine Learning

Highly Accurate and Efficient Prediction of Effective Thermal Conductivity of Sintered Silver Based on Deep Learning Method

Thermal Conductivity Prediction of SiC/Silicone Rubber Composites with Log-Normal Distributed Size Fillers and Multiple Connection Mechanisms via Separate Axis Theorem-Finite Element Combined Model

Reducing Migration of Sintered Ag for Power Devices Operating at High Temperature

Development of Ag@Si composite sinter joining with ultra-high resistance to thermal shock test for SiC power device: Experiment validation and numerical simulation

An Artificial Neural Network Model for Electro-Thermal Effect Affected Hot Carrier Injection Reliability in 14-nm FinFETs

Thermal Conductivity Prediction of SiC/Silicone Rubber Composites Using Combined Separate Axis Theorem-Finite Element Model

A combined experimental and modelling approach for the evaluation of the thermoelectric properties of Ag-doped SnS

A thermal conductivity varying 3D numerical model for parametric study of a silicon-based nano thermoelectric generator

Microstructural and Mechanical Evolution of Silver Sintering Die Attach for SiC Power Devices During High Temperature Applications

An SEM-Based Finite Element Analysis of Cu-Ag Sintered Joints on Thermal Shock Reliability

Failure analysis and reliability evaluation of silver-sintered die attachment for high-temperature applications

Numerical modeling of in-plane thermal conductivity measurement methods based on a suspended membrane setup

A Computational Multiscale Modeling Method for Nanosilver-Sintered Joints with Stochastically Distributed Voids

Study on Defect Detection and Impact on Heat Dissipation in Nanosilver Substrates

Discrete element model for effective electrical conductivity of spark plasma sintered porous materials

High Electrical and Thermal Conductivity of Nano-Ag Paste for Power Electronic Applications

Thermal Characterization of Silicon Carbide MOSFET Module Suitable for High-Temperature Computationally Efficient Thermal-Profile Prediction