Abstract:An aerodynamic optimization design process of multistage axial turbine is presented in this article: first, applying quasi-three dimensional (Q3D) design methods to conduct preliminary design and then adopting modern optimization design methods to implement multistage local optimization. Quasi-three dimensional (Q3D) design methods, which mainly refer to S2 flow surface direct problem calculation, adopt the S2 flow surface direct problem calculation program of Harbin Institute of Technology. Multistage local optimization adopts the software of Numeca/Design3D, which jointly adopts genetic algorithm and artificial neural network. The major principle of the methodology is that the successive design evaluation is performed by using an artificial neural network instead of a flow solver and the genetic algorithms may be used in an efficient way. Flow computation applies three-dimensional viscosity Navier?Stokes (N-S) equation solver. Such optimization process has three features: (ⅰ) local optimization based on aerodynamic performance of every cascade; (ⅱ) several times of optimizations being performed to every cascade; and (ⅲ) alternate use of coarse grid and fine grid. Such process was applied to optimize a three-stage axial turbine. During the optimization, blade shape and meridional channel were respectively optimized. Through optimization, the total efficiency increased 1.3% and total power increased 2.4% while total flow rate only slightly changed. Therefore, the total performance was improved and the design objective was achieved. The preliminary design makes use of quasi-three dimensional (Q3D) design methods to achieve most reasonable parameter distribution so as to preliminarily enhance total performance. Then total performance will be further improved by adopting multistage local optimization design. Thus the design objective will be successfully achieved without huge expenditure of manpower and calculation time. Therefore, such optimization design process may be efficiently applied to the aerodynamic design optimization of multistage axial turbine.

Aerodynamic Optimization Design of a Multistage Centrifugal Steam Turbine and Its Off-Design Performance Analysis

One-Dimensional Optimization Design of Supercritical Carbon Dioxide Radial Inflow Turbine and Performance Analysis under Off-Design Conditions

Feasibility Analysis and Realization of a Three-dimensional Aerodynamic Optimization Design for a Multi-stage Turbine

Study on Aerodynamic Optimization Design Process of Multistage Axial Turbine

Study on Aerodynamic Optimization Design of Multistage Axial Turbine under Multiple Working Conditions

Analysis of Off-Design Characteristics of Multistage Turbines

Aerodynamic Optimisation of a Low-Pressure Multistage Turbine Using the Response-Surface Method

An Integrated Design and Optimization Approach for Radial Inflow Turbines-Part II: Multidisciplinary Optimization Design

Aerodynamic Optimization Design and Analysis on the Turbine Part of F Class Gas Turbine under Middle and Low Heat Value Fuel

Multistage Aerodynamic Design Optimization on an Aeroengine Turbine

Multidisciplinary Optimization Design of Long Blade Turbine Stage Based on Parallel Self-Adaptive Multi-Objective Differential Evolution Algorithm

Analysis and Improvement of a Two-Stage Centrifugal Compressor Used in an MW-Level Gas Turbine

Design and analysis of a multi‐stage axial turbine for gasified coal‐water power system

The Design and Performance Analysis of a Highly-Loaded Turbine

Fluid Dynamic Efficiency Optimization of Steam Turbine Stages Considering Leakage Influences and Inter-stage Reciprocal Interferences

A Multi-Factor Comprehensive Optimization of a Supercritical Carbon Dioxide Radial Inflow Turbine with Low Specific Speed

Numerical Simulation and Aerodynamic Optimization of Two-Stage Axial High-Pressure Turbine Blades

Aerodynamic Numerical Investigation Of Low-Pressure Steam Turbine Last Stage Under Low Load Conditions With Mode Decomposition Methods

Aerodynamic Design and Analysis of a Multistage Vaneless Counter-Rotating Turbine

A comprehensive preliminary design methodology and an optimization workflow for single-stage radial-outflow turbines and application for 10 MW sCO 2 turbines

Preliminary Design Of Multistage Radial Turbines Based On Rotor Loss Characteristics Under Variable Operating Conditions