Abstract:An approach to design RF all-port-reflectionless quasi-elliptic-type single-/dual-band bandpass filters (BPFs) and diplexers with frequency-adaptive constant-absolute-bandwidth (ABW) response is reported. The tunable reflectionless BPF case is first addressed, where a balanced-circuit scheme composed of two identical wideband 3-dB quadrature couplers and two equal reflective-type BPF units with synchronous center-frequency agility is exploited. The input signal is split into the two BPF units with equal amplitude and 90° phase shift by the first coupler and then recombined at the output node of the second coupler after being processed by the balanced-circuit branches. In this manner, the signals reflected at the stopband regions of the BPF units are mutually canceled at the coupler input port and absorbed at the isolated port by its loading resistor. This allows a symmetrical low-reflection behavior to be attained in the overall circuit, whose filtering transfer function is the one determined by the BPF units. Furthermore, by using dual-band BPFs in the balanced-circuit branches, this concept is readily extended to frequency-tunable constant-ABW dual-band BPFs whose passbands can be separately switched OFF (i.e., absorptive switched-OFF states) as an added reconfiguration capability. For practical-demonstration purposes, starting from theoretical design guidelines followed by an optimization step, the third- and second-order microstrip prototypes of reflectionless frequency-controllable single- and dual-band BPFs with predefined constant ABW, respectively, are developed and tested. Afterward, inspired by the devised tunable absorptive BPF structure, an all-port-reflectionless diplexer with frequency-adjustable constant-ABW channels is shown. This controllable multiport-absorptive filtering device is also verified with the fabrication and testing of a microstrip prototype. All the constructed circuits employ varactor diodes for electronic tuning, -howing close agreement between simulation and measurements.

Design of Broadband Low-Pass Reflective Phasers

Shunt-Stub and Stepped-Impedance Broadband Reflective Phasers

A Broadband Rejection Filter Based on Spoof Surface Plasmon Polaritons

Broadband Nonreciprocal Spoof Plasmonic Phase Shifter Based on Transverse Faraday Effects

Synthesis of Narrowband Reflection-Type Phasers With Arbitrary Prescribed Group Delay

Compact Reflection-Type Phaser Using Quarter-Wavelength Transmission Line Resonators

Design of dispersion‐reconfigurable phaser using stepped‐impedance line

Parasitic Effect Suppression with Resonance Cancelation for Broadband Absorber/Reflector

Planar Reflective Phaser and Synthesis for Radio Analog Signal Processing (R-ASP)

Broadband Binary-Reflection-phase Metasurfaces with Undistorted Transmission Wavefront Via Mirror Symmetry

A Broadband Reflector Using a Multilayered Grating Structure with Multi-Subpart Profile

Non-uniform C-section Phasers for Enhanced Design Flexibility in Radio Analog Signal Processing

Design of Dispersion-Reconfigurable Phaser Using PIN-Diode Loaded Stepped-Impedance Line

Broadband Anomalous Refractor Based on Dispersion Engineering of Spoof Surface Plasmon Polaritons

Design of a Wideband Transmitarray Phaser Using Vivaldi Antenna for Dispersive Delay Radiation

Design Of A Dispersion-Switchable Phaser For Chirping Modulation

Metasurface‐Based Spatial Phasers for Analogue Signal Processing

Frequency-Tunable Constant-Absolute-Bandwidth Single-/Dual-Passband Filters and Diplexers With All-Port-Reflectionless Behavior

Short-circuited Stub-Loaded Spoof Surface Plasmon Polariton Transmission Lines with Flexibly Controllable Lower Out-of-band Rejections

Surface Plasmon Reflector Based on Serial Stub Structure.

Terahertz Broadband Spoof Surface Plasmon Polaritons Using High-Order Mode Developed from Ultra-Compact Split-Ring Grooves