Abstract:Pulse-jet bag filters are frequently employed for particle removal from off gases. Separated solids form a layer on the permeable filter media called filter cake. The cake is responsible for increasing pressure drop. Therefore, the cake has to be detached at a predefined upper pressure drop limit or at predefined time intervals. Thus the process is intrinsically semi-continuous. The cake formation and cake detachment are interdependent and may influence the performance of the filter. Therefore, understanding formation and detachment of filter cake is important. In this regard, the filter media is the key component in the system. Needle felts are the most commonly used media in bag filters. Cake formation studies with heat treated and membrane coated needle felts in pilot scale pulse jet bag filter were carried out. The data is processed according to the procedures that were published already [Powder Technology, Volume 173, Issue 2, 19 April 2007, Pages 93-106]. Pressure drop evolution, cake height distribution evolution, cake patches area distribution and their characterization using fractal analysis on different needle felts are presented here. It is observed that concavity of pressure drop curve for membrane coated needle felt is principally caused by presence of inhomogeneous cake area load whereas it is inherent for heat treated media. Presence of residual cake enhances the concavity of pressure drop at the start of filtration cycle. Patchy cleaning is observed only when jet pulse pressure is too low and unable to provide the necessary force to detach the cake. The border line is very sharp. Based on experiments with limestone dust and three types of needle felts, for the jet pulse pressure above 4 bar and filtration velocity below 50 mm/s, cake is detached completely except a thin residual layer (100-200 μm). Uniformity and smoothness of residual cake depends on the surface characteristics of the filter media. Cake height distribution of residual cake and newly formed cake during filtration prevails. The patch size analysis and fractal analysis reveal that residual cake grow in size (latterly) following regeneration initially on the base with edges smearing out, however, the cake heights are not leveled off. Fractal dimension of cake patches boundary falls in the range of 1-1.4 and depends on vertical position as well as time of filtration. Cake height measurements with Polyimide (PI) needle felts were hampered on account of its photosensitive nature.

Simulation of the Formation of Dust Cake in Particulate Air Filtration

Development and Validation of Filtered Drag Models for Fluidization of Low-Density Geldart A Particles

Simulative Prediction of Ultrafine Particulate Matter Formation by Means of Different Pyrolysis Models

A Numerical Model for Predicting Particle Collection Efficiency of Electrostatic Precipitators

Numerical Simulation of the Flow and the Collection Mechanism Inside a Scale Hybrid Particulate Collector

Adjustable fiber structure design for precise aerosol filtration

Simulation of soot particle deposition inside porous walls based on lattice Boltzmann method for diesel particulate filter

Lumped model for evaluating dynamic filtration and pressure drop behaviour in diesel particulate filters

The pressure drop of fibrous surface filters for gas Filtration: Modeling and experimental studies

Analysis of filtration process of 3-D mesh spacer filter by using CFD-DEM simulation

Simulation and test of flow process in air filter

Numerical investigation of non-spherical particle deposition characteristics on filter media

Extended filtration model for diesel particulate filter based on diesel particulate matter morphology characteristics

Filtration efficiency analysis of fibrous filters: Experimental and theoretical study on the sampling of agglomerate particles emitted from a GDI engine

Study of structural factors of structure-resolved filter media on the particle loading performance with microscale simulation

Dust Removal Principle and Numerical Simulation of New Type Cyclone-bag Combined Dust Collector

Dust Collection's Efficiency of Low Reynolds Purifier via Computational Fluid Dynamic Simulation and Optimization

Enhancement of particle collection efficiency considering the structural interplay: particle motion characteristics analysis

Experimental study of cake formation on heat treated and membrane coated needle felts in a pilot scale pulse jet bag filter using optical in-situ cake height measurement

Particle Deposition in A Full Scale Hybrid Electrostatic-Filtration Collector

A Coupled CFD-DEM Model for Resolved Simulation of Filter Cake Formation during Solid-Liquid Separation