Abstract:Vitrification is a promising treatment for municipal solid waste incineration fly ash (MSWI-FA); however, high energy consumption due to the high MSWI-FA fusion temperature limits the development and application of this technique. In this study, fine slag ash (FSA) derived from coal gasification and coal gangue ash (CGA) were mixed with MSWI-FA to reduce the ash fusion temperature. The transformation of minerals in ash during thermal treatment was examined via X-ray diffraction and thermodynamic equilibrium calculations. The ash flow behaviour was observed using a thermal platform microscope, and the silicate structure was quantified using Raman spectra. The co-melting mechanisms for the mixed ash were systematically investigated. Results indicate that the flow temperature (FT) of the mixed ash exhibited an initial decrease and subsequent increase as a function of the addition ratio of FSA or CGA. Lowest ash FT of 1215 °C and 1223 °C were recorded for addition of 50% FSA and 50% CGA, respectively; further, these temperatures were lowered by > 285 °C and >277 °C respectively, relative to FT of the MSWI-FA. The transformation of minerals and silicate structure during mixed ash heating was responsible for the variation in the ash fusion temperature. CaO in MSWI-FA tended to react with mullite, quartz and haematite in FSA and CGA, forming minerals such as anorthite, gehlenite, and andradite with relatively low melting points. The addition of FSA or CGA caused changes in the silicate network structure of the mixed ash. In particular, 50% FSA incorporation caused the transformation of Q4 and Q3 to Q2, whereas 50% CGA introduction resulted in the conversion of Q4 and Q2 into Q3 and Q1 + Q0, respectively. The silicate network depolymerised, causing reduction in the ash fusion temperature and increasing the melting rate.

Experimental Study on Coal Gasification-Swirling Melting Technology for Integrated Treatment of MSWI Fly Ash

Stabilization of Heavy Metals in Municipal Solid Waste Circulating Fluidized Bed Incineration Fly Ash by Fusion–hydrothermal Method

Swirling Melting Characteristics of Fly Ashes from Co-Firing of MSWI in China

Microwave-Assisted Hydrothermal Treatment with Soluble Phosphate Added for Heavy Metals Solidification in MSWI Fly Ash

Leaching of Heavy Metals from MSWI Fly Ash: Experiments Vs. Simulation

Immobilization Mechanism of Heavy Metals by Crystals and Liquid Phase During Melting Treatment of MSWI Fly Ash

Effects of Hydrothermal Treatment on the Major Heavy Metals in Fly Ash from Municipal Solid Waste Incineration

Mineralogy and Surface Properties of Melting Slag of MSWI Fly Ash in Swirling Furnace

Effect of Additive and Washing Pre-treatment on Heavy Metal Vaporization During Sintering Process of MSWI Fly Ash

Mineral transformation and solidification of heavy metals during co-melting of MSWI fly ash with coal fly ash

High temperature melting of municipal solid waste incineration (MSWI) fly ash and co-disposal technology with blast furnaces

Melting Characteristics During the Vitrification of MSW Incinerator Fly Ash by Swirling Melting Treatment

Stabilization of Heavy Metals in Municipal Solid Waste Incineration Fly Ash in Circulating Fluidized Bed by Microwave-Assisted Hydrothermal Treatment with Additives

An Experimental Study on the Melting Solidification of Municipal Solid Waste Incineration Fly Ash

Behaviour study of Cr during melting separation process of MSW incineration fly ash

Progress in Characteristics of Heavy Metals During Melting of Fly Ashes from Municipal Solid Waste Incinerator

Experimental study on MSW gasification and melting technology

Co-melting mechanisms for municipal solid waste incineration fly ash with fine slag from coal gasification and coal gangue

Microstructures and Thermal Properties of Municipal Solid Waste Incineration Fly Ash

Chromium behaviour during iron-bath melting separation process of MSW incineration fly ash

SEM/EDS and XRD characterization of raw and washed MSWI fly ash sintered at different temperatures.