Abstract:Continuous basalt fiber (CBF) is a new type of performance outstanding inorganic nonmetallic material. In comparison with carbon fibers, basalt fibers exhibit greater failure strain as well as better impact and fire resistance with less poisonous fumes and 50% cost reduction. It is also known that basalt fibers display higher mechanical properties, better chemical stability and superior thermal and electrical insulation as compared with glass fibers. Basalt fiber has been widely used as a reinforcing composite material for construction industry and for preparation of polymer matrix composites. As high-performance low-cost reinforcements, basalt fibers should have a great potential for strengthening metal matrix composites (MMCs) and reducing their preparation cost. However, so far, few reports focused on the investigation on metal matrix composites reinforced by continuous basalt fibers, especially for lack of feasible fabrication technologies. Thus, in the present work, two-dimensional continuous basalt fiber cloth and Al12Si alloys foils were selected as raw materials and alternately stacked to obtain a sandwiched structure. Subsequently, vacuum pressure infiltration was utilized to fabricate aluminum matrix composites reinforced by continuous basalt fibers (CBF/Al) with volume fraction of 65% successfully. Influence of infiltration parameters on microstructure evolution of resulting aluminum matrix composites was investigated and formation mechanism of multi-layered structure of CBF/Al composite was clarified. Moreover, mechanical properties of the multi-layered CBF/Al composite were evaluated. The results showed that when the infiltration parameters were 660., 10 MPa and 10 min, fully dense CBF/Al composite could be achieved and the novel composite displayed a unique multi-layered structure, namely continuous basalt fibers in forms of cruciform crossing distributed within aluminum alloys matrix. It is noteworthy that no obvious chemical reaction happened between continuous basalt fibers and Al-12Si alloys, and sound metallurgical bonding interface between them was obtained due to the interdiffusion of Al and Si elements. Unfortunately, mechanical properties of multi-layered CBF/Al composite did not reach a desired level, which was attributed to (i) decreasing of effective load-carrying capacity due to the imperfect distribution manner of continuous basalt fibers and (ii) deteriorating of intrinsic mechanical properties at high temperature.

Study on the Mechanic Properties of Steel Wire-Continuous Basalt Fiber Composite Plates

Mechanical Behavior of BFRP-Steel Composite Plate under Axial Tension

Behavior of RC Beams Strengthened Using Steel-Wire-Carbon-Fiber-Reinforced Plates

Uniaxial Tensile Behavior of Anchored Carbon Fabric-Reinforced Cementitious Matrix Plates

Mechanical Properties and Microstructures of Steel-basalt Hybrid Fibers Reinforced Cement-based Composites Exposed to High Temperatures

Experimental Study on Basic Mechanical Properties of Basalt Fiber Reinforced Concrete

Enhancement of the Tensile Strength of Titanium/Aluminum Triple-layer Composite Panels Using Steel Fiber

Experimental Study of Steel Plate Composite Shear Wall Units under Cyclic Load

Experimental Research on Fatigue Behavior of RC Beams Strengthened with Steel Plate-Concrete Composite Technique

Mechanical Properties of Steel Crane Beam Strengthened by CFRP

Dynamic compressive failure strength analysis of CBF basalt fiber stiffened laminated plates

Study of A Reinforced Concrete Beam Strengthened Using A Combination of Sma Wire and Cfrp Plate

Fabrication and Mechanical Characteristics of Multi-Laminated Aluminum Matrix Composites Reinforced by Continuous Basalt Fibers

Mechanical Behavior and Crack Width Control of Hybrid Fiber Reinforced Ductile Cementitious Composites

Mechanical Characterization of Hybrid Steel Wire Mesh/Basalt/Epoxy Fiber-Reinforced Polymer Composite Laminates

Development of a Novel Anchorage and Tensioning System for Strengthening Steel Beams with Unbonded Prestressed CFRP Plates

Experimental study and model of steel plate concrete composite members under tension

Study on Mechanical Properties of Multi-Cavity Steel-Concrete Composite Beam

Flexural Behavior of Steel Plate-Concrete Composite Beams

Experimental and theoretical study on flexural behavior of steel-concrete composite beams strengthened by CFRP plates with unbonded retrofit systems

Strengthening RC Beams with Mid-Span Supporting Prestressed CFRP Plates: an Experimental Investigation