Abstract:As a new element of flame, tubular flame especially the swirl type has excellent flame characteristics such as negligible heat loss, aerodynamic stability and thermodynamic stability. The premixed swirl type tubular flame has been extensively studied through a variety of burners, and various applications have been proposed and demonstrated for determining the flammability limits, stabilizing a flame in a high speed flow, and obtaining a uniform and large-area laminar flame to heat iron slab or to reduce steel sheet surface. To avoid potential hazards of flame flash back even detonation in premixed mode, an inherently safe technique of rapidly mixed tubular flame combustion has proposed, in which the fuel and the oxidizer are individually and tangentially injected into a cylindrical burner from four rectangular slits. Recently this burner has been successfully adopted to investigate the characteristics of oxygen enhanced combustion of methane, which provides a useful tool to save energy and reduce emissions. The results illustrate that the mixing of fuel and oxidizer plays a vital role in obtaining a stable tubular flame. To fundamentally investigate the flow field especially the mixing process in the rapidly mixed tubular flame burner, a series of measurements have been made on the flow visualization and velocity distribution with a Particle Image Velocimetry (PIV) system. Two groups of optically accessible quartz burners were designed: in the first group, the width of the rectangular slit was maintained as 2 mm while the length varied from 8 to 64 mm, in which the swirl number (Sw) varied from 2.75 to 0.34; in the second group, the slit width increased from 1 to 3 through 2 mm while maintaining the slit length as 8 mm, in which the swirl number decreased from 5.89 to 1.70 through 2.75. The total flow rate and the mean injection velocity ratio of fuel inlet to oxidizer inlet were also varied to measure the mixing layer thickness through flow visualization in a cross section perpendicular to the tube axis around the center of the burner. Detailed observation shows that the mixing layer thickness around the inlet is dominated by a boundary layer type flow regardless of swirl number and injection velocity ratio. The coefficients for the thickness estimation based on the square root of injection velocity (in reverse relationship) have been summarized. In addition, for a constant total flow rate, the mixing is fastest when the mean injection velocity of each inlet is the same. The flow visualization and the axial velocity distribution in a plane containing the tube axis were also analyzed to illustrate the flow motion downstream of the injection slits. The results demonstrate that a reverse flow appears in the burners of swirl number larger than 0.60.

Study on Flow Field Characteristic of Petal Swirl Burner

Experimental and Numerical Study of a Two-Stage Swirl Burner

TEST STUDY ON OUTLET FLOW FIELD PERFORMANCE FROM WAVE-SHAPED COMBUSTION-STABILIZING BODY OF THE CONCENTRATION TUNABLE RICH/LEAN BURNERS

Numerical Simulation of Gas-Particle Flows with Different Swirl Numbers in a Swirl Burner

Experimental study on the effect of particle size on the exit flow field of a swirl burner

Experimental studies on gas-particle flows in a swirl burner by PDPA measurements

Experimental study on cold two-phase flow in swirl burner exit

Effect of swirl number on the number of particle impacts near a swirl burner outlet

Recirculating Structures and Combustion Characteristics in a Reverse-Jet Swirl Pulverized Coal Burner

Flamelet LES of a Swirl-Stabilized Multi-Stream Pulverized Coal Burner in Air and Oxy-Fuel Atmospheres with Pollutant Formation

Experimental study on combustion flow field characteristics of swirl combustor

Isothermal swirling flow characteristics and pressure drop analysis of a novel double swirl burner

Direct Numerical Simulations and Analysis of Three-Dimensional N-Heptane Spray Flames in a Model Swirl Combustor

Simulation of Turbulent Multiphase Flow and Pulverized Coal Combustion in Swirl Combustor

An Experimental Study on the Flow Visualization in Rapidly Mixed Tubular Flame Burners of Various Swirl Numbers

Study on the flow characteristics and oscillating mechanism of a swirl flame

Studies on a Swirling Heptane Spray Flame by Large-Eddy Simulation

Study on combustion characteristics of swirl premixed combustor

Experimental study of stratified swirl flame dynamics in a model gas turbine combustor

Experimental Study of Particle-Laden Turbulent Reacting Flow in a Swirl Combustor

The Effect of Inner Secondary Air on the Flow Field of a Swirl Burner