Abstract:Warm rotary draw bending provides a feasible method to form the large-diameter thin-walled (LDTW) TC4 bent tubes, which are widely used in the pneumatic system of aircrafts. An accurate prediction of flow behavior of TC4 tubes considering the couple effects of temperature, strain rate and strain is critical for understanding the deformation behavior of metals and optimizing the processing parameters in warm rotary draw bending of TC4 tubes. In this study, isothermal compression tests of TC4 tube alloy were performed from 573 to 873 K with an interval of 100 K and strain rates of 0.001, 0.010 and 0.100 s−1. The prediction of flow behavior was done using two constitutive models, namely modified Arrhenius model and artificial neural network (ANN) model. The predictions of these constitutive models were compared using statistical measures like correlation coefficient (R), average absolute relative error (AARE) and its variation with the deformation parameters (temperature, strain rate and strain). Analysis of statistical measures reveals that the two models show high predicted accuracy in terms of R and AARE. Comparatively speaking, the ANN model presents higher predicted accuracy than the modified Arrhenius model. In addition, the predicted accuracy of ANN model presents high stability at the whole deformation parameter ranges, whereas the predictability of the modified Arrhenius model has some fluctuation at different deformation conditions. It presents higher predicted accuracy at temperatures of 573–773 K, strain rates of 0.010–0.100 s−1 and strain of 0.04–0.32, while low accuracy at temperature of 873 K, strain rates of 0.001 s−1 and strain of 0.36–0.48. Thus, the application of modified Arrhenius model is limited by its relatively low predicted accuracy at some deformation conditions, while the ANN model presents very high predicted accuracy at all deformation conditions, which can be used to study the compression behavior of TC4 tube at the temperature range of 573–873 K and the strain rate of 0.001–0.100 s−1. It can provide guideline for the design of processing parameters in warm rotary draw bending of LDTW TC4 tubes.

A New Method to Determine Plastic Constitutive Parameters of Tube and Its Applications

Experimental study and capacity analysis of double-tapered rectangular steel tubes

Predicting Plastic Behavior of Magnesium Alloy Tube Bending with Comprehensive Constitutive Models

Research on Bending Forming Method of Large Diameter-Thickness Ratio Thin-Walled Tubes for Aerospace

Numerical and experimental study on in-plane bending of microchannel aluminum flat tube

Bending Strength of Thin-Walled Centrifugal Concrete-Filled Steel Tubes

Numerical Analysis and Design of Concrete-Filled Wire Arc Additively Manufactured Steel Tube under Axial Compression

Mechanical Modeling of Tube Bending Considering Elastoplastic Evolution of Tube Cross-Section

Experimental Investigation And Design Of Concrete-Filled Cold-Formed Thin-Walled Steel Tubes Subject To Bending

Plastic Limit Load Analysis of Pressure Pipes Containing Incomplete Welding Defects under Combined Loadings

High Precision of Tube Modal Analysis Considering of Tube Bending Effect

Plastic Limit Load Analysis for Pressure Pipe with Incomplete Welding Defects Based on the Extended Net Section Collapse Criteria

Numerical Study on Plastic Strain Distributions and Mechanical Behaviour of a Tube under Bending

Identification of Anisotropic Coefficients in the Non-Principal Axis Directions of Tubular Materials Using Hole Bulging Test

Constitutive modeling of compression behavior of TC4 tube based on modified Arrhenius and artificial neural network models

Non-linear Analysis on Cast Tubular T-joint Loaded by In-Plane Bending

Finite Element Analysis of Seamless Steel Tube NC Bending

Bending Process Parameters Optimization of the 316L Tube with Small R/D Ratio: A Physical Prior Knowledge Based Bayesian Optimization Approach

Finite-Elements Modeling and Simulation of Electrically-Assisted Rotary-Draw Bending Process for 6063 Aluminum Alloy Micro-Tube

Modeling and Experimental Investigation of U-R Relationship of AA6061-T6 Tubes Manufactured via Free Bending Forming Process

Influence of Tube Ends Constraint on Hydro-Bending of Thin-Walled Aluminum Tube