Abstract:Author(s): Xia, Yi | Advisor(s): Ozolins, Vidvuds | Abstract: Thermoelectric materials, which enable direct conversion between thermal and electrical energy, provide an alternative for power generation and refrigeration. The key parameter that defines the efficiency of thermoelectric materials is the ‘dimensionless figure of merit’ ZT, which is composed of the Seebeck coefficient, electrical conductivity and total thermal conductivity respectively. Ideally, to achieve high ZT both the Seebeck coefficient and electrical conductivity should be large, while total thermal conductivity must be minimized. In this thesis, first-principles calculations of the Seebeck coefficient, lattice thermal conductivity and electrical conductivity are performed to study mechanisms and factors that gives rise to high ZT.One effective way to enhance ZT is through direct reduction of lattice thermal conductivity. We perform calculation and analysis of lattice thermal conductivity for thermoelectric materials by solving the Boltzmann transport equation iteratively in the framework of perturbation theory. The second- and third-order interatomic force constants are extracted using the recently developed CSLD (compressive sensing lattice dynamics) method. Afterwards, we evaluate opportunities to achieve further reduction of lattice thermal conductivity. Our first study of ternary zinc-blende-based mineral compounds famatinite (Cu3SbS4) and permingeatite (Cu3SbSe4) shows that optical modes in these two compounds contribute a sizable portion of the total lattice thermal conductivity and thus cannot be neglected. Due to the fact that phonon modes with mean free paths larger than 10 nm carry about 80% of the heat, nanostructuring, which reduces the mean free path, is a promising way to reduce the lattice thermal conductivity by reducing the characteristic length. In addition, our simple alloying model including mass disorder reproduces experimental findings that forming solid solutions rapidly decreases the lattice thermal conductivity. An alternative way to reduce lattice thermal conductivity is to introduce guest atoms in host cage structures. Our study of type-I Si clathrates containing guest atoms Na and Ba shows that Na tends to form incoherent localized phonon mode while Ba coherently couples with the host cages. The low lattice thermal conductivities of Na- and Ba-filled Si clathrates should be attributed to the dramatic reductions in both phonon lifetime and group velocity. Analysis of phonon scattering process reveals that localized modes can be effectively emitted and absorbed, thus dramatically enhancing overall scattering rates.Another widely adopted approach to achieve high ZT is through maintaining a high power factor. To accurately determine the Seebeck coefficient and electrical conductivity, we estimate carrier lifetime due to electron-phonon interaction under relaxation time approximation using the electron-phonon Wannier interpolation technique. Our study of noble metals Cu and Ag shows that their positive Seebeck coefficients can be mostly attributed to the negative energy dependence of carrier lifetime. In contrast to the previous study of positive Seebeck in Li, which is due to the deviation of electronic behavior from that in free electron model, it is the nontrivial energy dependence of electron-phonon interaction vertex that leads to the positive Seebeck coefficient. Intermetallic compound B20-type CoSi has drawn considerable attention due to its exceptionally high power factor and large Seebeck coefficient. Our study shows that the large negative Seebeck coefficient of the pristine CoSi is mostly due to the strong energy dependence of carrier lifetime, which together with the high electrical conductivity leads to the high power factor. For heat transport, both electron-phonon and phonon-phonon interactions contribute significantly to phonon scattering at temperatures lower than 200 K. While at temperatures higher than 300 K, phonon-phonon interaction dominates over electron-phonon interaction. Based on the optimized power factor with properly adjusted carrier concentration, we predict that the maximum ZTs at 300 and 600 K are about 0.11 and 0.25 respectively without further reducing the total thermal conductivity.Known good thermoelectric materials often are comprised of elements that are in low abundance, toxic and require careful doping and complex synthesis procedures. High performance thermoelectricity has been reported in earth-abundant compounds based on natural mineral tetrahedrite (Cu12Sb4S13). Our first-principles electronic structure calculations of Cu12Sb4S13 show that Cu atoms are all in the monovalent state, creating two free hole states per formula unit of the pristine compound. Optimal thermoelectric performance can be achieved via electron doping. Substituting transition metals on Cu 12d sites does the job. Detailed analysis shows that Zn and Fe substitutions tend to fill the empty hole states, while Ni substitution introduces an additional hole to the valence band by forming ferromagnetic configuration. Experimentally observed extremely low lattice thermal conductivity can be attributed to the out-of-plane vibrations of the three-fold Cu ions. This is further verified by the large Gruneisen parameter calculated.

Thermoelectrics: from Bonding Asymmetry to Anharmonic Rattling in Cu12Sb4S13 Tetrahedrites: when Lone‐Pair Electrons Are Not So Lonely (adv. Funct. Mater. 24/2015)

From Bonding Asymmetry to Anharmonic Rattling in Cu12Sb4S13 Tetrahedrites: when Lone‐Pair Electrons Are Not So Lonely

Structure Change and Rattling Dynamics in Cu12Sb4S13 Tetrahedrite: an NMR Study.

Rattling and Band-Filling Effects in Substituted Tetrahedrites: an NMR Study

Achieving Both Low Lattice Thermal Conductivity and High Hardness by the Design of Bonding Structure

Cu4Bi4Se9: A Thermoelectric Symphony of Rattling, Anharmonic Lone-pair, and Structural Complexity.

Remarkably Weakened Atomic Bonds from Dimeric Antibonding Hybridization and Enhanced Thermoelectric Performance of CdTe2

Chemical Bonding Engineering for High-Symmetry Cu2S-based Materials with High Thermoelectric Performance

Weak Bonding and Anharmonicity in Thermoelectric ZnSb

Cr2ge2te6: High Thermoelectric Performance from Layered Structure with High Symmetry

Remarkably Weakened Atomic Bonds from Dimeric Antibonding Hybridization and Enhanced Thermoelectric Performance of CdTe 2

Achieving High Average Power Factor in Tetrahedrite Cu12Sb4S13 Via Regulating Electron-Phonon Coupling Strength

Low thermal conductivity and promising thermoelectric performance induced by resonant bonding in a two-dimensional lead-tin-selenide ordered alloy

Electronic Transport and Thermoelectric Properties of Cu12-xZnxSb4S13 Tetrahedrites Prepared by Mechanical Alloying and Hot Pressing

Erratum: Strong Phonon-Phonon Interactions Securing Extraordinary Thermoelectric Ge1- xSbxTe with Zn-Alloying-Induced Band Alignment (J. Am. Chem. Soc. (2019) 141 (1742-1748) DOI: 10.1021/jacs.8b12624)

First-Principles Studies of Phonons and Electrons in Bulk Thermoelectrics

Band Modification Towards High Thermoelectric Performance of SnSb2Te4 with Strong Anharmonicity Driven by Cation Disorder

Improved Thermoelectric Performance of Cu 12 Sb 4 S 13 through Gd-Substitution Induced Enhancement of Electronic Density of States and Phonon Scattering

Observation of High Seebeck Coefficient and Low Thermal Conductivity in [Sro]-Intercalated CuSbSe2 Compound

Colloidal Synthetic Environmental Design Towards High-Density Twin Boundaries and Boosted Thermoelectric Performance in Cu5FeS4 Icosahedrons

Functional-Unit-Based Material Design: Ultralow Thermal Conductivity in Thermoelectrics with Linear Triatomic Resonant Bonds