Abstract:Recently, sodium ion batteries (NIBs) gained increasing attention, because of its abundant reserves and relatively even geological distribution. However, the development of NIBs is greatly hampered because of the lack of appropriate active materials for both cathodes and anodes. Since the Na ion is ca. 55% larger than the Li ion, finding suitable host materials with sufficiently large interstitial space to accommodate sodium ions and to allow reversible and rapid ion insertion and extraction is very difficult. NASICON-type Na3V2(PO4)3 has recently been considered as a prospective cathode material for NIBs, because of its highly covalent 3D framework crystalline structure, high energy density (~400 Wh/kg) and good thermal stability. For anode materials, disordered carbon is particularly attractive because of their large interlayer distance and disordered structure that could accommodate sodium ions. Here, we briefly present porous carbon based electrodes for NIBs with excellent rate performance: (1) Carbon-coated nanosized Na3V2(PO4)3 embedded in the porous carbon matrix (abbreviated as CC-NVP@PCM); (2) Nitrogen-doped activated porous carbon fibers (ACFs); (3)Flexible free-standing porous carbon nanofibers (P-CNFs) with three-dimensional (3D) interconnected structure. The CC-NVP@PCM was prepared by using a facile soft-chemistry based method with post heat-treatment. It shows high rate performance (44 mAhg-1at 200C ). This ultrahigh rate performance is comparable to that of supercapacitor, but with much higher energy density. The ACFs were synthesized by pyrolysis of Ppy nanofiber precursor. It shows excellent capacity retention and extraordinary rate performance. The reversible capacity at 0.05 Ag-1 is 296 mAhg-1 and could still maintain as 72 mAg-1 at a current of 10 Ag-1. In case of the P-CNFs electrode prepared by electrospinning, it delivers a reversible capacity of 266 mAh.g-1 after 100 cycles at 0.2C, corresponding to 80.3 % of the initial charge capacity. When cycled at a current density as high as 500 mAg-1 (2C), it still delivers a reversible capacity of ~140 mAh.g-1after 1000 cycles. The improvement of electrochemical performance of these porous carbon based electrodes for NIBs is attributed to the special design and porous structure, which confined a variety of advantages: hierarchical porous channels enabling short transport length for ions and electrons, carbon coated structure resulting in low resistances, good mechanical properties leading to the excellent morphology stability.

High Energy Density CNT/NaI Composite Cathodes for Sodium‐Ion Batteries

Enhanced Silicon Diphosphide-Carbon Composite Anode for Long-Cycle, High-Efficient Sodium Ion Batteries

Rayleigh-Instability-Induced Bismuth Nanorod@Nitrogen-Doped Carbon Nanotubes As A Long Cycling and High Rate Anode for Sodium-Ion Batteries

A Novel NASICON-Type Na3.5MnCr0.5Ti0.5(PO4)3 Nanofiber with Multi-electron Reaction for High-Performance Sodium-Ion Batteries

Electrodes for Sodium-Ion Batteries with Excellent Rate Performance Using Porous Carbon Networks

A NASICON-type Na3.67Cu0.17Fe0.5V1.33(PO4)3 cathode with multi-electron reaction for high-energy sodium-ion battery

Fabricating Na/In/C Composite Anode with Natrophilic Na–In Alloy Enables Superior Na Ion Deposition in the EC/PC Electrolyte

Advanced Na-Ion Batteries Based on Porous Nanocarbon Composites and Hybrids

Double-Morphology CoS2 Anchored on N-Doped Multichannel Carbon Nanofibers As High-Performance Anode Materials for Na-Ion Batteries

A High-Voltage Honeycomb-Layered Na4niteo6 As Cathode Material for Na-Ion Batteries

High-Entropy-Stabilized Polyanionic Cathodes with Multiple Redox Reactions for Sodium-Ion Battery Applications

CNT-Decorated Na4Mn2Co(PO4)(2)P2O7 Microspheres As a Novel High-Voltage Cathode Material for Sodium-Ion Batteries

Carbon Coated Sodium-Titanate Nanotube As an Advanced Intercalation Anode Material for Sodium-Ion Batteries

Intercalation Pseudocapacitive Nanoscale Nickel Hexacyanoferrate@Carbon Nanotubes As a High-Rate Cathode Material for Aqueous Sodium-Ion Battery

Free-Standing Sandwich-Structured Flexible Film Electrode Composed of Na2Ti3O7 Nanowires@CNT and Reduced Graphene Oxide for Advanced Sodium-Ion Batteries

Synthesis and Electrochemical Investigation of O3-Type High-nickel NCM Cathodes for Sodium-ion Batteries

NiCo2S4 Nanoparticles Anchored in the 3D Interpenetrating Framework Composed of GNs and CNTs Toward Enhanced Sodium Storage Performance

Facile Ion Diffusion and High Electrical Conductivity Enable High-Energy and High-Power Sodium-Ion Batteries from a Layered Metal-Free Cathode

Design of coherent anode materials with 0D Ni3S2 nanoparticles self-assembled on 3D interconnected carbon networks for fast and reversible sodium storage

Core/Double-Shell Structured Na3V2(PO4)2F3@C Nanocomposite As the High Power and Long Lifespan Cathode for Sodium-Ion Batteries

Spatial Confinement of Co1.67Te2 Nanoparticles Within Porous Carbon Nanofibers Enabling Fast Kinetics and Stability for Sodium Dual-Ion Batteries